Sharp VL-E630U/T Manual de usuario

yp&yT

VL:E665Urr

SHARP SERVICE MANUAL

SYBASJL-E630U

LIQUID CRYSTAL CAMCORDER q

NTSC

VL-E630U/T

VL=E680U

MODELS VL-E685U/T

In the interests of user-safety (Required by safety regula-

tions in some countries) the set should be restored to its

original condition and only parts identical to those specified

be used.

CONTENTS

Page

2. SPECIFICATIONS .............................................................................................................................. 2

4. DISASSEMBLY OF THE SET ............................................................................................................. 3

5. MECHANISM ADJUSTMENT.. ........................................................................................................... 4

6. ADJUSTMENT OF VCR.. .................................................................................................................... 5

8. SCHEMATIC DIAGRAMS.. ................................................................................................................ 8

11 .REPLACEMENT PARTS LIST .......................................................................................................... 29

12.PACKlNG OF THE SET .................................................................................................................... 35

SHARP CORPORATlON This document has been published to be used for

after sales service only.

The contents are subject to change without notice.

~p3o~fr

VL:E685Un

2. SPECIFICATIONS

Signal System:

Recording System:

Cassette:

Recording/Playback Time:

Tape Speed:

Pickup Device:

Lens:

Lens Filter Diameter:

Monitor:

Microphone:

Color Temperature Compensation

Minimum Illumination:

Video Output Level:

Audio Output Level:

Speaker Output:

Power Requirement:

Power Consumption:

Operating Temperature:

Operating Humidity:

Storage Temperature:

Dimensions (approx.):

Weight (approx.):

NTSC standard

2 rotary heads, helical scanning system

8 mm video tape, MP type

120 minutes (P6- 120)

14.345 mm/second

l/4” (6.4mm, effective size: 4.5 mm) CCD image sensor with approx.

270,000 pixels including optical black

16 x power zoom lens (F1.4, f=4.0-64.0 mm) and full-range auto focus

46 mm

3” (7.5 cm)-full-color LCD screen (TFT active matrix)

Electret monaural microphone

Auto white balance

0.8 lux (5 lux measured by EIA standard) (with gain-up, F1.4)

1.OVp-p 75-ohm unbalanced

-8 dBs, impedance less than 2.2 kohms

200 mW

DC 3.6V

E630U:4.8W (during camera recording in full auto mode with zoom

motor off, and backlight in normal mode)

E680U/E685U:4.9W (during camera recording in full auto mode with

zoom motor off, Extend Zoom, DIS and Snapshot functions off, and

backlight in normal mode)

0°C to + 40°C (32°F to 104°F)

30% to 80%

-20°C to +6O”C (-4°F to 140°F)

7 5/32”(W) x 4 g/$ (H) x 3 7/~” (D)

[182 mm (W) x 109 mm (H) x 99 mm (D)]

1.52lbs (690g)

(without battery pack, lithium battery, video cassette, and lens cap)

AC Adapter/Battery Charger Battery Pack BT-H22

UADP-0274TAZZ(VL-E63OU/680U/685U)

UADP-0275TAZZ(VL-E63OT/685T) DC Output: 3.6V

Dimensions (approx.): 2 l/s” (W) x 3/4”(H) x 2 7/32”(D)

Power Requirement:

DC Output:

Power Consumption:

Dimensions (approx.):

AC 11O-240 V, 50160 Hz

4.5 v

16W

2 31/32” (W) x 2” (H) x 5 5/16”(D)

r/5mm(W)x51 mm(H)x

135 mm (D)]

0.65 Ibs (295 g)

k$,mmm(OJx19mm

O-4

Weight (approx.): 0.30 Ibs (136 g)

Weight (approx.):

Specifications are subject to change without notice.

SERVICE INFORMATION (For the U.S.)

For the location of the nearest Sharp Authorized Service, or to obtain product literature, accessories,

supplies or customer assistance, please call l -800-BE SHARP (l-800-237-4277) or visit SHARP’s

web site (http://www.sharp-usa.com)

4. DISASSEMBLY OFTHE SET

4-2. Disassembly of the VCR main body

1. Removal of the VCR lid shaft

(l)Remove one screw ((j)LX-HZ0063TAFC).

4-3. REPLACEMENT OF CCD SENSOR

4-3-l. BEFORE REPLACEMENT

1) The CCD image sensor is more sensitive to electrostatic breakage than C-MOS LSI. Therefore sufficient means to

prevent electrostatic damage must be taken when it is replaced.

l Ground the soldering iron.

l Ground also the human body, using the wrist strap(through an 1 Mohm resistor).

l Until the CCDsensor is mounted on the PWB, fit it to the conductive sponge, and short-circuit the foot lead.

2) Take utmost care so that the surface glass of CCD sensor and optical filter are not contaminated and damaged. Ifany

contamination is found, for example fingerprint, wipe it off with silicon paper or clean chamois skin.

3) When replacing the CCD sensor, use the antistaic grounded soldring iron, and perform quickly soldering.

Index Mark 1 7

SHARP

LZ2413H5

4-4. INITIAL SE-KING OF EzPROM IC

4-4-2. IC702(E*PROM)

When the IC702 has been replaced, make the following settings and adjustments.

Remove the backup battery (CR2029

Turn power switch to CAMERA

Setting up the V ADJ mode as follows.

After press the CONTINUE key, press the VCR ADJ key on service remote control

After setting the above data, clear the V ADJ mode and turn off the power by pull out the battery pack or DC cable.

Neglect about 30 seconds after turned of power, because data of address becomes effective after microcomputer is

reset.

(RRMCG0033TASA).

Now the setting of data is completion.

Adjustments to follow

Make the system controller servo, VCR, and LCD adjustments according to their respective instructions.

VL-E63olJ/l

VL-E68ou

VL-E685U/T

5. MECHANISM ADJUSTMENT

5-2. Items and timings of inspection and maintenance

5-2-l.Inspection and maintenance list -

Remarks

CheckingIvlaintenance point 5oo

t- Usag

1,000

, !

time

1,5oc hrs.) Possible symptom

?,OOO3,000 encountered

cl cl l

Lateral noise

Unclean head

Screen shaking

cl cl

no 00 l

Improper S/N ratio

No color appears.

* * l Tape does not run.

Tape slackens.

o q l

Screen shakes.

0 0

A A l Abnormal sound

Rollers

Ifabnormal rotation or

deflection (signifi-

cant) is found, replace

the roller.

Other than rollers

*Clean the tape con-

tacting areas. Besure

to use the specified

cleaning agent.

. Replace if failure is

found.

Timing belt

Pinch roller

Capstan D.D. motor

Relay Pulle shaft

Pulle gear shaft

Drive gear shaft

- A A

l-l l

Apply oil.

(Oil:

Note:

)

After oil is applied to

the drive gear shaft,

slightly wipe it off with

swab.

I I

Not ejectable l Replace if failure (ab-

*o 90 l

The specific modecan- normal sound) is de-

not be set. tected.

If conformance to the

standard is not en-

sured, replace part.

Abnormal sound sr

PBNS-REW take-up torque -

PBNS-REW back tension -

torque

Tu brake -

HC (Head Cleaner) -

I 1

* *

I I

* I * I

I I

0 : Replace.

0 : Clean. A : Apply oil.

+ : Check.

Oil:

Grease: MORYCOAT YM-103/X5-6020

Screw locking agent: THERE BOND 1401B

Cleaning liquid: Industrial-use ethyl alcohol

5-4. ADJUSTMENT OF MECHANISM TAPE TRAVEL SYSTEM

5-4-3.Adjusting the Si roller height

(2) Adjusting the Si roller

1 Playback the tape such to set the V/SR mode.

6. ADJUSTMENT OF VCR

6-1. ADJUSTMENT OF VCR SECTION

6-l-5. Y/C circuit adjustment method

3. Adjustment of playback Y level

5. Adjustment of Y-FM deviation

Measuringinstrument Oscilloscope

Mode REC/PB (self-playback/recording)

Input signal Color bar

Measuring point TL801

Adjustment address 34

Adjustment level 500 f 20 mVp-p

6-l-7. Adjustment of LCD display circuit

9. lnverter input voltage setting

Measuring point LCD panel display surface

Address 11,12

Mode VCR AV input

Adjusting method Set the data of address 11 and 12.

Adjustmentstandard 11=BD

12=8E

Remarks

6-2. ADJUSTMENT OF CAMERA SECTION

l Connections for Camera Section Servicing

LENS

F -

20pin i

k-----k

CCD PWB

SC3

* Preparation for 6-2-2-3-6-2-2-9; set up the camera signal adjustment mode. (Write 00 to the address 1FE.)

6-2-2-3.

Before starting these adjustments, set up the auto focus adjust.

l Sync level adjustment

Measuringinstrument Oscilloscope

Subject Anything

Tape -

Test point VIDEO OUT (Terminated in 75Q)

Adjustmentaddress 1FE

Adjustment level 286mVp-p

1) Connect the oscilloscope to the VIDEO-OUT. Adjust the

sync level to 286mVp-p.

6-2-2-9.

l Auto white balance adjustment

Measuringinstrument Vector scope

Subject Gray scale

Tape -

Test point VIDEO OUT (Terminated in 75 Q)

Adjustment address R-OUT DOOR 016

B-OUT DOOR 018

Adjustment level R-OUT DOOR; 0 + 3 %

B-OUT DOOR; 0 + 3 %

Video

R-Y

/ spot

1) Attach the color temperature conversion filter (JIGHOYA-LB165) to the front of the lens.

2) Using the addresses R-OUT DOOR 016 and B-OUT DOOR 018, adjust the spot to the center.

3) Take off the color temperature conversion filter.

Ir Write FF to the address 1FE to the address 1FE to exit the camera adjustment mode.

-MEMO-

_-_------___-------________________________-_------________-----______-------_____-------_

_____------_____----------______-------_________---__________-_-__________--_________-----

_-______---_______-----________---________________________________________________________

____------______-------____-_-----_____________________-_____________________--________---

_-----___-------___------------~~~----------~___--------____------~__--------~~__--_---~~~

------___--________----__---------________________________________________________________

_-_-_____--________----_____________________________________~________________--________---

~----___------__----------~~~~----------_____-----_____-----_______---______----_____-----

____------_---------__--------________________________________________________--__________

_-_--______-----____-_--------_______---_______---________--_________-________--_______---

______----______----____________________________________________________________________-_

___---________----______------___________________-________--________--_______---_____----~

8. SCHEMATIC DIAGRAM

8-2. POWER CIRCUIT SCHEMATIC DIAGRAM

I -

-f

VL-E63OWT

VL-E66OU

VL-E66!5U/T

‘t

/--I

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Videocámara de Sharp

Sharp

Sharp VN-EZ1U Manual de usuario

Sharp

Sharp ViewCam Slim VL-ME100E Manual de usuario

Sharp

Sharp VL-H400X Manual de usuario

Sharp

Sharp 8C-B30A Manual de instrucciones

Sharp

Sharp ViewCam VL-AH131E Manual de usuario

Sharp

Sharp ViewaCam VL-H29E Manual de usuario

Sharp

Sharp VL-AX1U Manual de usuario

Sharp

Sharp VL-C73SA Manual de usuario

Sharp

Sharp ViewcamZ VL-Z7S Manual de usuario

Sharp

Sharp ViewcamZ VL-Z950E-A Manual de usuario

Sharp

Sharp E630U Manual de usuario

Sharp

Sharp Viewcam VL-WD450S Hoja de especificaciones

Sharp

Sharp VL-E780U Manual de usuario

Sharp

Sharp ViewCam VL-E89E Manual de usuario

Sharp

Sharp VL-E78E Manual de usuario

Sharp

Sharp Viewcam Z VL-Z7U Manual de usuario

Sharp

Sharp Zoom 8 VL-E30S Manual de usuario

Sharp

Sharp ViewCam Slim VL-AX1H Manual de usuario

Sharp

Sharp VL Z 1 H Manual de usuario

Sharp

Sharp ViewCam VL-AH131S Manual de usuario

Sharp

Sharp ViewCam Slim VL-ME100S Manual de usuario

Sharp

Sharp ViewCam VL-WD450E Manual de usuario

Sharp

Sharp VL-Z950S Manual de usuario

Sharp

Sharp ViewCam VL-H850S Manual de usuario

Manuales populares de Videocámara de otras marcas

Toshiba

Toshiba CAMILEO Z100 Manual de usuario

Panasonic

Panasonic NV-VS40B Manual de usuario

Canon

Canon RC 260 Manual de usuario

Sony

Sony Handycam DCR-DVD7E Manual de usuario

Brinno

Brinno TimeLapse TLC200 Manual de usuario

JVC

JVC GR-SXM68AC Guía de inicio rápido

Panasonic

Panasonic AG-HMC152EN Manual de usuario

Insignia

Insignia NS-DCC5HB09 - Camcorder - 720p Manual de usuario

MYDLINK

MYDLINK DCS-6100LH Manual de usuario

Sony

Sony video Hi8 Handycam CCD-TR555 Manual de usuario

SECURECOM

SECURECOM V-5014B Manual de usuario

Panasonic

Panasonic HDC-SD100 Manual de usuario

Sharper Image

Sharper Image U-VIDEO Manual de usuario

JVC

JVC AA-V15EG Manual de usuario

Canon

Canon LEGRIA HV40 Manual de usuario

Sony

Sony Handycam DCR-VX2000 Manual de usuario

RCA

RCA CC616 Manual de usuario

Panasonic

Panasonic NVM40 Manual de usuario