Sharp QS-1760H Manual de usuario

QS-1760H

QS-2760H

QS-2770H

ELECTRONIC PRINTING CALCULATOR

CALCULADORA IMPRESORA ELECTRÓNICA

OPERATION

MANUAL

MANEJO

ENGLISH ....................................... Page 2

CALCULATION EXAMPLES ......... Page 28

ESPAÑOL ...................................... Página 15

EJEMPLOS DE CÁLCULOS ......... Página 28

Caution!

The socket outlet shall be installed near the equipment and shall be easily accessible.

Aviso!

El tomacorriente debe estar instalado cerca del equipo y debe quedar bien accesible.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

WARNING - FCC Regulations state that any unauthorized changes or modifications to this

equipment not expressly approved by the manufacturer could void the user’s authority to

operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV technician for help.

– 1 –

QS-2770H

QS-1760H

QS-2760H

, : QS-2770H only

Sólo en la QS-2770H

THE KEYBOARD EL TECLADO

– 2 –

Thank you for your purchase of the SHARP electronic calculator, model QS-1760H/

2760H/2770H. Your SHARP calculator is specially designed to save work and increase

efficiency in all business applications and general office calculations. Careful reading of

this manual will enable you to use your new SHARP to its fullest capability.

To insure trouble-free operation of your SHARP calculator, we recommend the following:

1. The calculator should be kept in areas free from extreme temperature changes,

moisture, and dust.

2. A soft, dry cloth should be used to clean the calculator. Do not use solvents or a wet

cloth.

3. Turn off the power switch prior to connecting or disconnecting the AC cord.

4. Since this product is not waterproof, do not use it or store it where fluids, for example

water, can splash onto it. Raindrops, water spray, juice, coffee, steam, perspiration,

etc. will also cause malfunction.

5. If you pull out the power cord to cut electricity completely, the presently stored tax

rate will be cleared.

6. If service should be required on this equipment, use only a SHARP servicing dealer,

a SHARP approved service facility or SHARP repair service where available.

7. Do not wind the AC cord around the body or otherwise forcibly bend or twist it.

Note: Unless otherwise specified, the text material applies to all three models.

SHARP will not be liable nor responsible for any incidental or consequential

economic or property damage caused by misuse and/or malfunctions of this product

and its peripherals, unless such liability is acknowledged by law.

WARNING

THE VOLTAGE USED MUST BE THE SAME AS SPECIFIED ON THIS

CALCULATOR. USING THIS CALCULATOR WITH A VOLTAGE HIGHER THAN

THAT SPECIFIED IS DANGEROUS AND MAY RESULT IN A FIRE OR OTHER

TYPE OF ACCIDENT CAUSING DAMAGE. SHARP WILL NOT BE HELD

RESPONSIBLE FOR ANY DAMAGE RESULTING FROM USE OF THIS

CALCULATOR WITH OTHER THAN THE SPECIFIED VOLTAGE.

ENGLISH

INTRODUCTION

OPERATIONAL NOTES

– 3 –

Page

•OPERATING CONTROLS .......................................................................................... 3

•INK RIBBON REPLACEMENT ................................................................................. 11

•PAPER ROLL REPLACEMENT ................................................................................ 12

•ERRORS ................................................................................................................... 13

•DECIMAL SYSTEM ................................................................................................... 13

•SPECIFICATIONS .................................................................................................... 14

•CALCULATION EXAMPLES ..................................................................................... 28

•TAX RATE CALCULATIONS ..................................................................................... 45

•SAMPLE APPLICATIONS ......................................................................................... 47

POWER SWITCH:

When the power switch is turned on, the calculator is ready for operation.

PRINT MODE SELECTOR:

“P” position: The calculator functions as a print/display calculator. (Print

mode)

“•” position: The calculator functions as a display calculator. (Non-print

mode)

Mode change print:

When changing the print mode selector, the following print will appear.

“• • • .... • • • –P” (red print): When changing the selector from P to •.

“• • • .... • • • +P” (red print): When changing the selector from •to P.

GRAND TOTAL / RATE SETTING MODE SELECTOR:

“GT” position: This selector will accumulate the following:

(The symbol “ +” will be printed.)

1. Addition and subtraction totals obtained with the or

key.

2. Product and quotient totals obtained with the or

key.

3. Answers obtained with the or key.

“•” position: Neutral, GT OFF

“ ” position: •Enter the adding tax rate, then press .

•To store a discount rate, press before pressing

CONTENTS

OPERATING CONTROLS

– 4 –

•A maximum of 4 digits can be stored (decimal point is

not counted as a digit).

Note: •Be sure to set this selector to the “•” position after storing an

each rate.

•Only one rate can be stored. If you enter a new rate, the previous

rate will be cleared.

ADD MODE SELECTOR:

“A/+” position – Effective only in addition and subtraction:

Use of the A/+ mode permits addition and subtraction of

numbers without an entry of the decimal point. When the

A/+ mode is activated, the decimal point is automatically

positioned according to the decimal selector setting.

EXAMPLES: Set A/+- •-A/x to A/+

A. Set decimal to 2

Enter 123456 Tape prints 1,234.56 +

B. Set decimal to 3

Enter 123456 Tape prints 123.456 +

Use of the , , and keys will automatically override

the Add mode and decimally correct answers will be

printed at the preset decimal position.

EXAMPLES: Set A/+- •-A/x to A/+, 5/4

A. Set decimal to 2

Enter .1234 Tape prints 0.1234 ×

100 100.=

12.34

B. Set decimal to 3

Enter 2 Tape prints 2.

3 3.=

0.667

C. Set decimal to 2

Enter 123 Tape prints 1.23 +

10 10.00 +

11.23

Note that decimal point was entered.

“A/x” position – Multiplication and division:

When the A/x mode is activated, the number entered

before or key will override the add mode. But the

➝

– 5 –

number entered following or key and before (or

, , , , ) key will obey the decimal setting. This

is useful for invoicing.

EXAMPLE: Set A/+- •-A/x to A/x

Set decimal to 2

Enter 7 Tape prints 7.×

3 0.03 =

0.21

Note: Use of the key will automatically override the A/x

mode.

Addition and subtraction:

The A/x mode functions same as the A/+ mode.

“•” position: Neutral

ITEM COUNT MODE SELECTOR:

“IC±” position: 1) The counter will count the number of times that the

key has been pressed in addition.

Note: •Each time the key is used in subtraction, 1

will be subtracted from the count.

•The count is printed when the calculated

result is obtained.

•Pressing of the , , , or key

clears the counter.

2) When the grand total mode selector is in the ON

position (GT), the counter will count the number of

times that the calculation results have been stored in

the grand total memory. To print and clear the count,

press the key.

3) The memory item counter will count the number of

times that the key has been pressed in the addition.

Note: •Each time the key is used in the

subtraction, 1 will be subtracted from the

count.

•The count is printed when the memory is

recalled.

•Pressing of the key clears the counter.

“IC+” position: 1) The counter will count the number of times that the

or has been pressed in addition and subtraction.

Note: •The count is printed when the calculated

result is obtained.

– 6 –

•Pressing of the , , , or key

clears the counter.

2) When the grand total mode selector is in the ON

position (GT), the counter will count the number of

times that the calculation results have been stored in

the grand total memory. To print and clear the count,

press the key.

3) The memory item counter will count the number of

times that the or key has been pressed in

addition and subtraction.

Note: •The count is printed when the memory is

recalled.

•Pressing of the key clears the counter.

“•” position: Neutral, counter is turned off.

Note: The counter has a maximum capacity of 3 digits (up to ±999). If the

count exceeds the maximum, the counter will recount from zero.

FIRST FACTOR ACCUMULATION SELECTOR: (Only QS-2770H)

“FΣ” position: The first factor is automatically added to or subtracted from

the memory. A first factor means the first number in multi-

plication and division and each number is printed with “×I”

and “

I” respectively.

Ex. 2 ×3 ×5

6 =

7 ×9 =

–56 ×4 ×0.5 =

“•” position: Neutral

CONSTANT MODE SELECTOR:

“K” position: The following constant functions will be performed:

Multiplication: The calculator will automatically remember the first

number entered (the multiplicand) and the instruction.

Division: The calculator will automatically remember the second

number entered (the divisor) and the instruction.

Add-on/Discount/Mark up:

The calculator will automatically remember the first

entered number and key functions for Add-on/Discount/

Mark up calculation.

“•” position: Neutral

ROUNDING SELECTOR:

“” position: An answer is rounded up.

“5/4” position: An answer is rounded off.

– 7 –

“” position: An answer is rounded down.

EXAMPLE: 10.005

5 = 2.001

Set decimal to 2,

10.005 5 →2.01

Set decimal to 2, 5/4

10.005 5 →2.00

Note: The decimal point floats during successive calculation by the use of

or key.

In floating decimal point system, an answer is rounded down.

DECIMAL SELECTOR:

Presets the number of decimal places in the answer.

In the “F” position, the answer is displayed in the floating decimal system.

PAPER FEED KEY:

When pressed, advances the paper roll.

Note: You can also pull the paper manually.

RIGHT SHIFT KEY:

Operation of this key in entered numbers or calculated results shifts the

number one digit to the right together with the decimal point. Used for one

digit correction.

GRAND TOTAL KEY:

Prints and clears the “GT” memory contents.

NON-ADD/SUBTOTAL KEY:

Non-add – When this key is pressed right after an entry of a number in the

Print mode, the entry is printed on the left-hand side with the

symbol “#”.

This key is used to print out numbers not subjects to calculation

such as code, date, etc.

Subtotal – Used to get subtotal(s) of additions and/or subtractions. When

pressed following the or key, the subtotal is printed with

the symbol “

◊

” and the calculation may be continued.

By pressing this key even in the Non-print mode, the displayed number

is printed with the symbol “P”.

TOTAL KEY:

Prints the total of addition and subtraction with the symbol “ ”. This key also

serves as a clear key for the calculation register and resets an error

condition.

– 8 –

CLEAR ENTRY KEY:

Clears number entered prior to use of a function key.

Also used to clear an overflow error caused by an entry.

Ex. 123 ×455 →123 ×456 =

Press 123 455 456

~NUMERAL KEYS

MINUS EQUALS KEY:

Prints the entered number with a “–” symbol and subtracts the number from

the contents of the calculation register. This key is also used to obtain the

product/quotient in negative multiplication and division and prints it with the

symbol “ ”.

PLUS EQUALS KEY:

Prints the entered number with a “+” symbol and adds the number to the

contents of the calculation register. This key is also used to obtain the results

in multiplication and division and prints the product/quotient with the symbol

“”.

PERCENT KEY

DIVISION KEY

MULTIPLICATION KEY

FIRST MEMORY PLUS KEY

FIRST MEMORY MINUS KEY

FIRST RECALL MEMORY KEY

FIRST RECALL AND CLEAR MEMORY KEY

SECOND RECALL AND CLEAR MEMORY KEY

SECOND RECALL MEMORY KEY

SECOND MEMORY MINUS KEY

SECOND MEMORY PLUS KEY

DATE KEY: (only QS-2770H)

Can be used to store and display/print or recall the date or any other factor

for repeated use in an application.

AVERAGE KEY:

Used to calculate the average.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Calculadora de Sharp

Sharp

Sharp Compet CS-2122H Manual de usuario

Sharp

Sharp el-9950 Manual de usuario

Sharp

Sharp EL-338G Manual de usuario

Sharp

Sharp EL-509G Manual de usuario

Sharp

Sharp EL1801C - Semi-Desktop 2-Color Printing... Manual de usuario

Sharp

Sharp ELSIMATE EL-782C Manual de usuario

Sharp

Sharp ELSIMATE EL-327S Manual de usuario

Sharp

Sharp EL-503W Manual de usuario

Sharp

Sharp EL1611P - 12 Digit Hand Held Calculator AC/DC... Manual de usuario

Sharp

Sharp EL-1750PII Manual de usuario

Sharp

Sharp ELSIMATE EL-M812 Manual de usuario

Sharp

Sharp Elsi Mate EL-R297 Manual de usuario

Sharp

Sharp EL-T100WB Manual de usuario

Sharp

Sharp WriteView EL-W535XG Manual de instalación

Sharp

Sharp EL-1750V Manual de usuario

Sharp

Sharp W Series Manual de usuario

Sharp

Sharp EL-9450 Manual del propietario

Sharp

Sharp EL-R277B-BK Manual de usuario

Sharp

Sharp Elsimate EL-337C Manual de usuario

Sharp

Sharp EL1611P - 12 Digit Hand Held Calculator AC/DC... Manual de usuario

Sharp

Sharp EL-240S Manual de usuario

Sharp

Sharp EL-9900 Manual de usuario

Sharp

Sharp ELSIMATE EL-341S Manual de usuario

Sharp

Sharp EL-1901 Manual de usuario

Manuales populares de Calculadora de otras marcas

HP 35s Manual

Casio

Casio CFX-9970G Manual de usuario

LEXIBOOK

LEXIBOOK EL350 Manual de usuario

HP HP-97 Manual de usuario

Citizen

Citizen SDC-414N Manual de usuario

Casio

Casio fx-3800P Manual de usuario

Canon

Canon P26-DHIII Manual de usuario

Citizen

Citizen 520DPA Manual de usuario

Casio

Casio FX-9860GII - SOFTWARE VERSION 2-00 Manual de usuario

Casio

Casio MS-7UC Manual de usuario

Casio

Casio FC-200 Manual de usuario

Casio

Casio fx-CG50 Manual de usuario

HP HP-67 Guía del usuario

Royal

Royal CBC2000 Manual de usuario

Heathkit

Heathkit IC-2009 Manual de usuario

Universal

Universal UNV-15907 Manual de usuario

Casio

Casio ALGEBRA FX 2.0 Manual de usuario

Casio

Casio CLASSPad300 - ClassPad 300 Touch-Screen Graphing Scientific... Manual de usuario