Sharp X-M200DK Manual de usuario

This document has been published to be used for

after sales service only.

The contents are subject to change without notice.

Parts marked with “ “ are important for maintaining the safety of the set.

Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

INSTALLATION MANUAL

SHARP CORPORATION

[ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

[ 2 ] CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

[ 3 ] MX-M200D/MX-M160D/MX-M160 . . . . . . . . . . . . . . . . . . . . . . . 3-1

[ 4 ] AR-SP10/AR-RP10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

[ 5 ] AR-D34/AR-D35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

[ 6 ] MX-FX10/AR-MM9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

[ 7 ] MX-NB10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

[ 8 ] MX-TR10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

[ 9 ] CHANGING THE COPY PAPER SIZE IN THE TRAY. . . . . . . . . 9-1

[10] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

[11] AR-PF1 BARCODE FONT KIT

AR-PF2 MACRO FONT FLASH ROM KIT . . . . . . . . . . . . . . . . 11-1

[12] MX-PK10 PS EXPANSION KIT. . . . . . . . . . . . . . . . . . . . . . . . . 12-1

[13] AR-SM5 256Mb EXPANSION MEMORY . . . . . . . . . . . . . . . . . 13-1

DIGITAL

MULTIFUNCTIONAL

SYSTEM

MX-M200D

MX-M200DK

MX-M160D

MX-M160DK

MX-M160

As for the content of the MX-M200DK/MX-M160DK, refer to the

content of the MX-M200D/MX-M160D as long as there is no

CODE : 00ZMXM200DI1E

MX-M200D

MX-M160D

MX-M160

CONTENTS

MODEL

This product is a class 1 laser product that complies with 21CFR 1040.10 and 1040.11 of the CDRH standard and IEC60825-1 Edition 1.2-2001.

1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as a unit, not as individual parts.

2) Do not look into the machine with the main switch turned on after removing the developer unit, toner cartridge, and drum cartridge.

Do not look into the laser beam exposure slit of the laser optical unit with the connector connected when removing and installing the optical

system.

4) The middle frame contains the safety interlock switch.

Do not defeat the safety interlock by inserting wedges or other items into the switch slot.

The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time of servicing.

This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved on the eye's retina, there is the danger of

spot damage to the retina.

This means that this machine does not produce hazardous laser radiation. The use of controls, adjustments or performance of procedures other

than those specified herein may result in hazardous radiation exposure.

CAUTION

Warning:

This is a Cla

Disconnect the AC cord before servicing the unit.

LASER WAVE - LENGTH: 785 nm + 10 nm/ 15 nm

Pulse times : (8.141 s 0.1 s/7 mm

Output power : 0.14 mW 0.22 mW

ss A product. In a domestic environment this product may cause radio interference in which case

the user may be required to take adequate measures.

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

MX-M160D GENERAL 1 - 1

[1] GENERAL

1. Note for servicing

Pictogram

The label ( ) in the fusing area of the machine indicates the

following:

: Caution, risk of danger

: Caution, hot surface

A. Warning for servicing

•The fusing area is hot. Exercise care in this area when removing misfed

paper.

•Do not look directly at the light source. Doing so may damage your

eyes.

B. Cautions for servicing

•Do not switch the machine rapidly on and off. After turning the machine

off, wait 10 to 15 seconds before turning it back on.

•Machine power must be turned off before installing any supplies.

•Place the machine on a firm, level surface.

•Do not install the machine in a humid or dusty location.

•When the machine is not used for a long time, for example, during

prolonged holidays, turn the power switch off and remove the power

cord from the outlet.

•When moving the machine, be sure to turn the power switch off and

remove the power cord from the outlet.

•Do not cover the machine with a dust cover, cloth or plastic film while

the power is on. Doing so may prevent heat dissipation, damaging the

machine.

•Use of controls or adjustments or performance of procedures other than

those specified herein may result in hazardous laser radiation

exposure.

•The socket-outlet shall be installed near the machine and shall be easily

accessible.

C. Note for installation place

Improper installation may damage the machine. Please note the

following during initial installation and whenever the machine is moved.

Caution : If the machine is moved from a cool place to a warm place,

condensation may form inside the machine. Operation in this

condition will cause poor copy quality and malfunctions. Leave

the machine at room temperature for at least 2 hours before

use.

Do not install your machine in areas that are:

•damp, humid, or very dusty

•poorly ventilated

•exposed to direct sunlight

•subject to extreme temperature or humidity changes, e.g., near an air

conditioner or heater.

The machine should be installed near an accessible power outlet for

easy connection and disconnection.

Be sure to connect the power cord only to a power outlet that meets the

specified voltage and current requirements. Also make certain the outlet

is properly grounded.

Note : Connect the machine to a power outlet which is not used for other

electric appliances. If a lighting fixture is connected to the same

outlet, the light may flicker.

Be sure to allow the required space around the machine for servicing

and proper ventilation.

20 cm

)

20 cm

)

20 cm (8

)

MX-M160D GENERAL 1 - 2

D. Note for handling PWB and electronic parts

When handling the PWB and the electronic parts, be sure to observe the

following precautions in order to prevent against damage by static

electricity.

1) When in transit or storing, put the parts in an anti-static bag or an

anti-static case and do not touch them with bare hands.

2) When and after removing the parts from an anti-static bag (case), use

an earth band as shown below:

• Put an earth band to your arm, and connect it to the machine.

3) When repairing or replacing an electronic part, perform the procedure

on an anti-static mat.

MX-M160D CONFIGURATION 2 - 1

[2] CONFIGURATION

1. System Configurations

2. Machine configuration

[MX-M200D] [MX-M160D] [MX-M160]

(250-sheet paper

feed unit)

(2 x 250-sheet paper

feed unit)

[AR-RP10]

[AR-D35] [AR-D34]

[MX-TR10]

AR-RP10

(REVERSING SINGLE PASS FEEDER)

[AR-SP10] [AR-VR7] [MX-NB10]

(SINGLE PASS FEEDER) (DOCUMENT COVER)

(JOB SEPARATOR)

[MX-FX10]

(FACSIMILE

EXPANSION KIT)

(NEWORK PRINTING /

SCANNING

EXPANSION KIT)

Standard for North America only

MX-M200D MX-M160D MX-M160

Copy STD STD STD

Color scanner STD STD STD

SPLC printer STD STD STD

PCL printer OPT OPT OPT

Fax OPT OPT OPT

Network OPT OPT OPT

Duplex STD STD N/A

Sort STD STD STD

Paper tray 2-stage 1-stage 1-stage

MX-M160D CONFIGURATION 2 - 2

3. Option list

: Option installation enable

: Option installation disable

Model name Name MX-M200D MX-M160D MX-M160 Product key

target

AR-RP10 REVERSING SINGLE PASS FEEDER North/South America: STD

Europe, Australia, Agency: OPT

OPT N/A —

AR-SP10 SINGLE PASS FEEDER North/South America: N/A

Europe, Australia, Agency: OPT

OPT OPT —

AR-VR7 DOCUMENT COVER North/South America:N/A

Europe, Australia, Agency: OPT

OPT STD —

AR-D34 250-SHEET PAPER FEED UNIT OPT OPT OPT —

AR-D35 2X250-SHEET PAPER FEED UNIT OPT OPT OPT —

MX-TR10 JOB SEPARATOR TRAY KIT OPT OPT OPT —

MX-NB10 NEWORK PRINTING / SCANNING

EXPANSION KIT

OPT OPT OPT —

MX-FX10 FACSIMILE EXPANSION KIT OPT OPT OPT —

AR-SM5 256MB EXPANTION MEMORY BOARD OPT OPT OPT —

AR-MM9 FAX EXPANTION MEMORY BOARD OPT OPT OPT —

AR-PF1 BARCODE FONT KIT OPT OPT OPT —

MX-PK10 PS3 EXPANSION KIT OPT OPT OPT Ye s

AR-PF2 MACRO FONT FLASH ROM KIT OPT OPT OPT —

MX-M200D/MX-M160D/MX-M160 3 - 1

[3] MX-M200D/MX-M160D/MX-M160

1.Installing conditions

A.Copier installation

Do not install your copier in areas that are:

•damp, humid, or very dusty

•exposed to direct sunlight

•poorly ventilated

•subject to extreme temperature or humidity changes, e.g., near an air

conditioner or heater.

•Be sure to allow the required space around the machine for servicing

and proper ventilation.

B.Power source

•Use an exclusive to dedicated power outlet. If the power plug of this

machine is inserted into a power outlet commonly used with other

illumination units, flickers of the lamp may be result. Use a power outlet

which is not used commonly with any illumination units.

•Avoid complex wiring.

C.Grounding wire connection.

•To avoid danger, the power outlet must be grounded. If no grounding

wire is connected and a leakage occurs, a fire or an electric shock may

be result.

2. Removal of protective material and fixing

screw

1) Remove all tapes and protective material.

•Remove all tapes, then open the document cover and remove the

protective material of sheet shape

2) Remove the fixing screw.

•Use a coin to remove the fixing screw.

•The fixing screw is required when transporting the machine. Keep it in

the tray. (Refer to the later description.)

3.Installing procedure

A.Developer cartridge installation

1) Open the bypass tray, and open the side cover.

2) Open the front cover.

•Hold the both sides and pull down to open.

3) Loosen the screw and remove the developer cartridge.

4) Remove the developer tank from the developer cartridge.

5) Shake the developer bag enough before opening it, and supply the

developer into the developer tank.

• While rotating the MG roller in the arrow direction, supply the

developer into the developer tank evenly so as not to overflow.

MG roller

MX-M200D/MX-M160D/MX-M160 3 - 2

6) Check that two hooks of the developer unit is hooked on the toner

cartridge guide, and secure the toner cartridge guide to the

developing unit.

* Check that the DV seal is free from the developer. If developer is

attached to the DV seal, clean it.

* After supplying developer, do not tilt or shake the developer

cartridge.

7) Attach the developer cartridge to the main unit, and secure it with

the screw.

B.Toner cartridge installation

1) Remove the new toner cartridge from the bag. Grasp the cartridge

on both sides and shake it horizontally four or five times.

2) Insert the toner cartridge along the guides until it locks in place while

pushing the lock release lever

•If there is any dirt or dust on the toner cartridge, remove it before

installing the cartridge..

C. Set the toner density reference control level

1) With the front cover open, turn ON the machine power and enter

SIM25-02.

Note: When the machine is not in the simulation mode, if the front

cover is closed and the machine power is turned ON, toner

may be supplied from the toner cartridge to the developer

cartridge.

Under this state, the toner density reference control level

adjustment cannot be made properly.

Therefore, if the front cover is closed and the machine power

is turned ON with the machine not in the simulation mode,

dispose developer and supply new developer and adjust the

toner density reference level.

2) Close the front cabinet.

3) Press [START] key, and execute SIM25-02.

Note: It takes about 3 minutes to execute SIM25-02 completely.

During execution of this simulation, the front cover must not be

opened and the machine power must not be turned OFF.

4. Removal and storage of fixing screw

1) Lift the knob and gently pull out the tray.

2) Hold the paper pressure plate and turn the fixing screw in the arrow

direction.

3) Store the fixing pin and the fixing screw in the tray.

•Store the fixing screw which was removed in the above procedure 2 and

the fixing screw which was removed in procedure 2 of 2.

•Removal of protective material and fixing screw in the storage place in

the tray.

hook

4 or 5 times

Screw

fixing

AR-SP10/AR-RP10 4 - 1

[4] AR-SP10/AR-RP10

1. Unpacking

For unpacking, refer to the figure below.

2. Installation

Turn the main switch of the copier to the “OFF” position and then

remove the power plug of the copier from the outlet.

1) Remove the document cover.

Lift the document cover from the copier and tilt it to the rear side to

remove it.

2) Remove the right cabinet.

Remove the screws and remove the right cabinet.

3) Remove the document glass and the right document glass holder.

Remove the screws, remove the document glass from the copier, and

then remove the right document glass holder.

4) Attach the SPF glass holder.

Fit the SPF glass holder to the document glass.

Attach the document glass to the copier and fix it with the screws.

AR-SP10/AR-RP10 4 - 2

5) Attach the right cabinet.

Reattach the right cabinet to its original position and fix it with the

screws.

6) Cut out the cut-out portion.

Cut out the cut-out portion of the rear cabinet with nippers or the like.

At this time, be careful about the orientation of the nippers so that the

cut plane of the rear cabinet is flat.

7) Attach the automatic document feeder.

Insert the hinge portions of the document feeder into the mounting por-

tions of the copier by holding the feeder at an angle toward the rear

side.

8) Connect the relay connector.

Connect the harness of the automatic document feeder to the connec-

tor of the copier and tighten the screws on the connector.

9) Remove the filament tape.

Remove the filament tape located in the positions shown in the illustra-

tion.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora todo en uno de Sharp

Sharp

Sharp DM-2000 Manual de usuario

Sharp

Sharp DM-2000 Manual de usuario

Sharp

Sharp AL-2030 Manual de usuario

Sharp

Sharp MX-M3071 Manual de instrucciones

Sharp

Sharp AR-810 Imager Manual de usuario

Sharp

Sharp AR-M550N Manual de usuario

Sharp

Sharp MX-M1204 Manual de usuario

Sharp

Sharp AR 168S - Digital Imager B/W Laser Manual de usuario

Sharp

Sharp AR-M455N Manual de usuario

Sharp

Sharp AR-5618 Guía

Sharp

Sharp AR-M237 IMAGERs Manual de usuario

Sharp

Sharp MX-7001N Series Manual de instalación y funcionamiento

Sharp

Sharp MX-3050N Manual de usuario

Sharp

Sharp AR-M276 Manual de usuario

Sharp

Sharp MX-C301W Manual de usuario

Sharp

Sharp AR-M236 Manual de usuario

Sharp

Sharp MX-2300G Manual de instalación y funcionamiento

Sharp

Sharp MX-C311 Manual de instalación y funcionamiento

Sharp

Sharp MX-M904 Manual de usuario

Sharp

Sharp MX-M850 Manual de usuario

Sharp

Sharp AR-C360P Manual de programación

Sharp

Sharp MX-C250E Guía

Sharp

Sharp AL-2021 Guía

Sharp

Sharp AL-1651CS Manual de usuario

Manuales populares de Impresora todo en uno de otras marcas

Triumph Adler

Triumph Adler DC 2016 Manual

Epson

Epson WorkForce WF-2510 Guía del usuario

Epson

Epson Stylus Scan 2000 Manual de instalación y operación

Epson

Epson PictureMate Snap PM 240 Manual de instrucciones

Konica Minolta

Konica Minolta bizhub C35 Manual de usuario

Brother

Brother MFC-J430w Manual de usuario

Konica Minolta

Konica Minolta BIZHUB 558 Manual de usuario

Lexmark

Lexmark MX710 Series Manual

Brother

Brother MFC-9760 Manual de usuario

Lexmark

Lexmark XC8155 Manual de usuario

Lexmark

Lexmark X642E Manual de usuario

Aficio

Aficio 200 Manual de usuario

Canon

Canon ImageCLASS 2300 Manual

Ricoh

Ricoh Pro C900 Manual de usuario

Lexmark

Lexmark X925 Manual de usuario

Brother

Brother Business Smart MFC-J4510dw Manual de usuario

Epson

Epson Stylus CX8400 Series Manual de usuario

Oce

Oce VarioLink 5022 Manual de usuario