Servpro AIR SCRUBBER 892 Instrucciones de funcionamiento

INFORMATION

OPERATING

INSTRUCTIONS

#892 AIR SCRUBBER

120V

56041841

IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY

1. NEVER use the Air Scrubber without both the HEPA and the primary filter installed.

2. Use the Air Scrubber indoors only, and only for its designed purpose.

3. Always follow EPA approved guildelines for site preparation and contaminant disposal.

4. NEVER clean or re-use a HEPA filter. Handle and dispose of the HEPA filter as you would

other hazardous waste.

5. Keep the air inlet and outlet at least one foot from walls or other obstructions.

6. Plug the machine into a grounded 15 amp or greater outlet.

CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ

ALL SECTIONS OF THIS INSTRUCTION MANUAL

2-8-2010

IMPORTANT SAFETY INSTRUCTIONS

This machine is only suitable for commercial use, for example in hotels, schools, hospitals,

factories, shops and offices other than normal residential housekeeping purposes.

When using any electrical appliance, basic precautions should always be followed, including the

following:

NOTE: Read all instructions before using this machine.

WARNING!

To reduce the risk of fire, electric shock, or injury:

•Connect to a properly grounded outlet only.

•Exhausting air from an area containing open flame appliances (fireplace, gas hot water

heater or furnace, etc) can cause a “back-draft” effect. An air pressure differential can

cause the flames to burn low without consuming all the gas. This can contaminate the area

with hazardous gases, as well as cause a potentially explosive condition. When in this

situation you must (1) seriously limit the amount of air exhausting from the area to prevent

a negative pressure. Open flame appliances must be closely monitored to insure that no

back-draft occurs while the Patriot is being used, or (2) allow, or direct, the outlet air back

into the area with the open flame device. This will keep the pressure in the treatment area

normal and prevent a back-draft situation.

•Do not leave the machine unattended when it is plugged in. Unplug the unit from the outlet

when not in use and before servicing.

•To avoid electric shock, do not expose to rain or snow. Store, and use, indoors.

•Do not allow to be used as a toy. Close attention is necessary when used near children.

•Do not use with damaged cord or plug. If the machine is not working as it should, has been

dropped, damaged, left outdoors or flooded witlh liquid, return it to a service center.

•Do not handle the plug, the cord, or the machine with wet hands.

•Extension cords must be 12/3 and no longer than 50 feet.

•Do not put any object into openings. Do not use with any opening blocked.

•Keep loose clothing, hair, fingers, and all parts of body away from openings and moving

parts.

•Turn off all controls before unplugging.

Record the serial number and model of your new machine here:

(and be sure to register your purchase to active your warranty)

Serial Number: __________________ Model: Air Scrubber, #892

Purchase Date:_____________

Write the name and phone number of your distributor:

INSPECTION:

Carefully unpack and inspect the Air Scrubber for shipping damage. Each unit is

tested and inspected before shipment. Any damage incurred during shipping is the

responsibility of the carrier, whom you should notify immediately.

FILTERS:

The Air Filter must be used with the HEPA air filter and the Primary Filter. The

HEPA Filter has an efficiency rating of 99.97% in the removal of particles as small

as 0.3 microns. The Primary filter catches larger particles to prevent the early

loading of the HEPA filter. Additionally, two optional Filters are available: a

Secondary 2” Pleated Filter can be used between the Primary and HEPA Filters for

increased large particle reduction, and a 2” Carbon Filter may be used between the

Primary Filter and the Secondary (pleated) Filter. NOTE: always use the Secondary

Pleated Filter between the Carbon Filter and the HEPA filter to avoid premature

loading of the HEPA filter.

MAINTENANCE:

Change filters as needed. Check the red “Check Filter” light while the Air Scrubber

is running on high speed. Do not allow dirty filters to recontaminate area.

Before each job, inspect filters and gaskets to make sure they are ready for use.

Clean the body with an all purpose detergent, and protect it with a common auto

interior protectant. Lubricate the wheels as needed.

After setting up the treatment area and the Patriot -- according to EPA guidelines -- prepare

to turn the machine on.

CAUTION: Occupants of the treatment area must evacuate or wear approved protective

covering.

1. Turn the power switch OFF.

2. Check the filters and the gaskets to ensure proper installation, cleanliness, and seal.

Change filters as necessary -- indicated by the “Check Filter” light or as

directed by the Hygienist.

3. Close the lid and secure it tightly with the latches.

4. Connect the power cord to the receptacle in the control panel. Inspect for damage. Do

not use the cord if it is damaged. CAUTION: Make sure the switch is OFF before

connecting the cord.

5. Route the power cord so it is out of the way, out of any water, and not rubbing anything.

6. Plug the cord to a grounded, 120V outlet.

7. Set the switch to HIGH or LOW for either 1400 CFM or 2200 CFM.

WARNING: Always turn the machine off and disconnect the power cord before

changing filters.

WARNING: Wear NIOSH approved respirator and other protective covering.

CAUTION: Filters must be changed inside the treatment area, and disposed of properly.

HIGH / LOW SWITCH (2): This is the main power switch; it has three positons:

HIGH / OFF / LOW. The fan is turned OFF when the switch

is in the center position. Set the fan for 2200 CFM by

selecting HIGH and select 1400 CFM by setting the switch to

LOW.

CHECK FILTER LIGHT (1): This light will come on when the filters are loaded and need

to be replaced. Always check the light with the switch on

the HIGH setting. Turn the machine off to change filters.

CORD RECEPTACLE (3): This is where you connect the power cord. Connect the cord

here before connecting it to a wall outlet. Make sure the

switch is in the OFF (center) position when connecting power.

CHECK

LOW

HIGH

OFF

#1 #2

SET-UP:

The Air Scrubber can be operated while sitting flat on the floor (#1) or in an upright position

(#2), as shown below. Place the machine as shown in Figure 1 for large, open areas, or

locations near the same height as the machine. Use the upright position for areas that are

high above the location of the machine, such as ceiling ductwork or attic areas.

Use either wire reinforced ducting or layflat plastic tubing for Inlet and outlet air ducting, as

needed.

NOTE: The exhaust air must not be allowed to flow into uncontaminated or

occupied areas.

VENTILATION:

The Environmental Protection Agency (EPA) recommends one air exchange every fifteen

minutes (four times each hour). To establish the total air flow requirements:

Calculate the total volume of the contaminated area. Multiply width X length X height.

Example

: 60 ft long, 30 feet wide, 10 feet high

60 X 30 X 10 = 18000 cubic feet

18000/15 minutes = 1200 cubic feet per minute (CFM)

This is the minimum recommended rate at which the air should flow through the Air Scrubber.

The machine has two speeds, High (2200 CFM) and Low (1400 CFM). Use this calculation to

determine which setting to use.

Intake air

WARNING: exhausting air from an area containing open flame appliances (fireplace,

gas hot water heater or furnace, etc) can cause a “back-draft” effect. An air pressure

differential can cause the flames to burn low without consuming all the gas. This can

contaminate the area with hazardous gases, as well as cause a potentially explosive

condition. When in this situation you must (1) seriously limit the amount of air

exhausting from the area to prevent a negative pressure -- CAUTION: open flame

appliances must be closely monitored to insure that no back-draft occurs while the Patriot

is being used, or (2) allow, or direct, the outlet air back into the area with the open flame

device. This will keep the pressure in the treatement area normal and prevent a back-

draft situation.

Intake air

Exhaust

air

27A

28A

29B

29A

44 45

37 38

#892 Air Scrubber

02-08-2010

#892 AIR SCRUBBER

120V

PART LIST

1 1 ASFH-2 Filter Housing, green

1A 1 1014A Extrusion

2 1 1017 Guard, wire form, 18”

2A 4 5 Bolt, 1/4-20 # 3/4”

2B 4 8 Lock nut, 1/4-20

3 4 21C Screw, 8-32 X 5/8”

5 4 325 Lock nut, 8-32

6 2 908 Latch

7 4 1036A Rod, filter retaining, 14-1/2”

8 4 1043 Bracket, filter retaining

9 4 9 Nut, wing,1/4-20”

10 1 1015 Filter, pre, ring pan, 24” X 24” X 1”

11 1 1014C Filter, HEPA, 23-3/8” X 23-3/8”

12 1 AS-Lid- SP Lid, white

13 1 183 Plug, for lid

14 1 1043A Gasket, 3/8” X 94”

15 1 1007A Blower and Housing

16 2 79 Wire tie

17 1 1013 Capacitor, 30μfd

18 4 1012A Mounting leg, motor

19 1 1011A Band, leg mounting, four position

20 1 1006 Motor, 1-3/4 HP, 2-Speed, 115Volt

21 4 7 Lock nut, 5/16 X 4”

22 4 1032 Bolt, 5/16-24 # 2”

23 4 1010 Foot pad, rubber

27 1 1008A Mount leg, fan housing, left

27A 1 1008 Mount leg, fan housing, right

28 1 1020L Brace, fan housing, left

28A 1 1020R Brace, fan housing, right

29 1 ASFAN-2 Fan Housing

ITEM QTY PART No. DESCRIPTION

29A 1 002050 Gasket, 1/4” X 92”

29B 1 2050B Gasket, 3/8” X 44”

30 1 N/A Part of Fan Housing

31 1 910-22.63”Axle, 1/2” O.D. X 22.63”

32 2 2003 Wheel, 8”

33 2 27A Axle cap

34 1 1019 Guard, wire form, 12”

35 1 1002 Switch plate

36 6 1009 Screw, 1/4-20 X 5/8”

37 2 16 Lock nut

38 1 230 Cord retainer

39 1 1027 Hose Barb

40 1 1003 Recepticle, power cord

41 2 1152 Screw, 6-32 X 1/2”

42 1 1004 Sensor, pressure

43 1.5” 416 Tubing, 3/16” I.D.

44 1 78B Light, red, 115V

45 1 1005 Switch, ON-OFF-ON

ITEM QTY PART No. DESCRIPTION

MISCELLANEOUS ASSEMBLIES/PARTS

FP266 Duct Kit

1016 2” Pleated Pre-Filter

1042 Filter, carbon

1021A Label

NOTE: items in kits not sold separately

SPECIFICATIONS:

Hepa Filter:

Blower:

Blower Motor:

Weight:

Dimensions:

Warranty:

Warranty on Body:

Transport:

DOP Certified 99.97

Two speed 1400/2200 CFM

1-3/4 hp, 14 amp peak

130 lbs.

51L x 15-1/4W x 19-1/2H inches

1 year limited - parts

Lifetime

8 Inch transport wheel w/dolly design

#892 AIR SCRUBBER

120V

NOTES:

Tabla de contenidos

Otros manuales de Depurador de Servpro

Servpro

Servpro 879 Manual de usuario

Servpro

Servpro HVE3000 Manual de usuario

Manuales populares de Depurador de otras marcas

Olympus

Olympus M200H Manual de usuario

Clarke

Clarke BEXT 100H Manual de instalación y funcionamiento

JOHNY VAC

JOHNY VAC JVC70BCT Manual de usuario

RCm

RCm Elan Series Manual

Kärcher

Kärcher B 120 W Manual de usuario

Truvox

Truvox Orbis MotorScrubber 20 Manual de usuario

Numatic

Numatic TTB 4045/100 Manual de usuario

U.S. Products

U.S. Products PEX 500-C-TICK Instrucciones de funcionamiento

Mclennan

Mclennan C510 Manual de usuario

Tennant

Tennant T20 LPG Manual de usuario

Columbus

Columbus ARA 66 BM 100 Manual de usuario

Numatic

Numatic TTV 678G / 300T Manual de usuario

American-Lincoln

American-Lincoln 505-945 Manual de usuario

FIORENTINI

FIORENTINI ET 65-75 Manual de usuario

Floorpul

Floorpul ruby 48 blt Guía del usuario

Onyx

Onyx RX-34 Manual de usuario

Dustbane

Dustbane Hurricane 400 Manual de usuario

Sana

Sana EUJ-702 Manual de usuario