Sercomm xCAM Manual de usuario
xCAM
User’s Guide
i
Table of Contents
CHAPTER 1 INTRODUCTION..............................................................................................1
Overview ............................................................................................................................1
Physical Details - xCAM...................................................................................................2
Physical Details - XW3......................................................................................................4
Package Contents ..............................................................................................................5
CHAPTER 2 BASIC SETUP ...................................................................................................6
System Requirements........................................................................................................6
Installation .........................................................................................................................6
Wall Mounting...................................................................................................................9
APPENDIX A SPECIFICATIONS........................................................................................11
Spec...................................................................................................................................11
Regulatory Approvals.....................................................................................................12
Copyright ©2015. All Rights Reserved.
Document Version: 1.0
All trademarks and trade names are the properties of their respective owners.
1
Chapter 1
Introduction
This Chapter provides information of the xCAM's features, components and
capabilities.
Overview
Congratulations on the purchase of your new xCAM. The xCAM is a True Day/Night IP
camera that features high definition 1280 x 720p video resolution and 802.11n WiFi
connectivity.
Features
•Standalone Design. The xCAM is a standalone system with built-in CPU and Video
encoder. It requires only a power source and a connection to your touch screen.
•Dual Video Compressions. The xCAM supports H.264 and MJEPG video for different
image compressions.
•Suitable for Home, Business or Public Facilities. Whether for Home, Business or
Public Facility surveillance, or just for entertainment and fun, the xCAM has the features
you need.
•IR LED Support. Each xCAM has two infrared LED. The LEDs can provide
illumination around 5 meters long, that can help to output a better video quality while
under low-light conditions such as indoors, on cloudy days, or in the morning or evening.
Wireless Features
•Supports 802.11n Wireless Standard. The 802.11n standard provides backward
compatibility with the 802.11b and g standards. The xCAM can work with all 802.11n,
802.11b and 802.11g Wireless stations.
•Wired and Wireless Network. The xCAM can be connected either with wire or
wirelessly to your network.
1
2
Physical Details - xCAM
Front - xCAM
Figure 1: Front Panel
IR LEDs IR LEDs provide illumination at night or in a dark environment.
Lens No physical adjustment is required or possible for the lens, but you
should ensure that the lens cover remain clean. The image quality is
degraded if the lens cover is dirty or smudged.
POWER indicator
(Blue/Yellow) On (Blue) - The xCAM is paired.
Flashing (Blue) - The xCAM is connected to router but not paired.
Flashing (Yellow) - The xCAM is not connected to XW3 or XW3 is
not connected to a router.
3
Rear - xCAM
Figure 2: Rear Panel
RJ-45 Jack This RJ-45 connector is used for power connection when the camera
is under wireless mode. A customized PoE (Power over Ethernet)
splitter, as a Y-cable, is provided to allow connection to PC for
setup and pairing.
Reset Button This button has two (2) functions:
•Reboot. When pressed and released, the xCAM will reboot
(restart).
•Clear All Data. This button can also be used to clear ALL data
and restore ALL settings to the factory default values.
To Clear All Data and restore the factory default values:
1. Power On.
2. Keep holding the Reset Button down for 8 seconds.
3. Release the Reset Button. The xCAM is now using the factory
default values.
Microphone The built-in microphone is located on the rear of the device.
4
Physical Details - XW3
XW3
LAN Port To be connected to the RJ-45 jack of xCAM for power feed and data
exchange.
Reset Button This button has the following function:
•Reset to manufacturer default valued and reboot. When
pressed and held over 10 seconds, the settings of the XW3 will
be set to their default values.
WPS Button Push the WPS button on the device and on your other wireless
device to perform WPS function that easily creates an encryption-
secured wireless connection automatically.
POWER indicator
(Blue/Yellow) On (Blue) - The XW3 is connected to a router.
Rapid Flashing (Blue) - WPS association is in process.
Slow Flashing (Blue) - The XW3 is not configured or trying to
connect to a router.
Flashing (Yellow) - The XW3 is not connected to a router.
5
Package Contents
The following items should be included in the package: If any of these items are damaged or
missing, please contact your dealer immediately.
•xCAM Unit (with Stand and Ethernet RJ-45 pigtail) * 1
•Y-cable * 1
•Screw/Anchor x 2
•XW3 Unit * 1
6
Chapter 2
Basic Setup
This Chapter provides information on how to install and configure the xCAM.
System Requirements
•To use the Wireless interface on the wireless model, other Wireless devices must be
compliant with the IEEE802.11n, IEEE802.11b or IEEE802.11g specifications. All
Wireless stations must use compatible settings.
Mode: Infrastructure
SSID: ANY
Wireless Security: Disabled
Domain: USA
Channel No.: Auto
Installation
You must complete the following installation procedure when using the xCAM for the first
time.
Step 1 - Adding an xCAM to your network
Make sure the Router and the Touch Panel are both powered on and synchronized before
adding your xCAM. This step is required when an xCAM is used for the FIRST time. It only
needs to be done ONCE in order to configure the wireless settings for the xCAM.
Note: Skip this section if the xCAM has been set up already.
1.On the Touch Panel, click on Setting icon on the home page.
2.Enter the "Master"code.
3. Enter the "Technical code/ID", then click the "Done" button.
4. Select "Home Devices". Then choose "Cameras-> Add a Camera".
5. Click the "Next" button to check network.
2
Tabla de contenidos
Otros manuales de Cámara IP de Sercomm
