LEARNING OF TRANSMITTER CODE
The control panel has an incorporated two-channel receiver at 433,92 Mhz which allows to remotely drive the gate
through transmitters at dip-switches - OG/02 and OG/04 - and also self-learning transmitters OG/62, OG/64,
OG/52, OG/54, OG/82/1 and OG/84. The first channel of the receiver works like a start, while the second channel
works like “pedestrian” start.
ERASING OF THE STORED CODES
Keep pressed the button A (SET) for about 10sec. Until the LED DL10 switches off.
!ATTENTION: - before using a transmitter, it is compulsory to program it
- the max number of codes is 32 for the START function and 32 for the
PEDESTRIAN function (different combination are not possible: for ex. 40 start + 24
pedestrian NOT POSSIBLE).
Some examples of the possible combinations:
32 self-learning transmitters- example A: OG/62, OG/64, OG/28, OG/48, OG/52,
OG/54, OG/82/1 or OG/84 as (for ex. the left push-button)+
OG/62, OG/64, OG/28, OG/48, OG/52, OG/54,
OG/82/1 or OG/84 as (for ex. the right push-button)
- example B: OG/62, OG/64, OG/28, OG/48, OG/52,
OG/54, OG/82/1 or OG/84 as (for ex. the left push-button) +
OG/02, OG/04 as (it is not necessary to program
the other OG/02 or OG/04 since it is enough to set the dip-switches in the
same position) + OG/62, OG/64, OG/28,
OG/48, OG/52, OG/54, OG/82/1 or OG/84 as (for ex. the right
push-button) + OG/02, OG/04 as (it
is not necessary to program the other OG/02 or OG/04 since it is enough
to set the dip-switches in the same position)
start 32 self-
learning transmitters
pedestrian
31 self-learning transmitters
start 1 dip-
switch transmitter start
31 self-learning transmitters
pedestrian
1 dip-switch transmitter pedestrian
!
DAL 1965
Page 9/10
LEARNING OF THE START CODE
- Control panel ON, gate closed. the button A (SET) to enter into programming. LED DL10 starts
flashing. The programming phase begins.
- Press the button in the transmitter (for ex. the left button) and keep it pressed until LED DL10 switches OFF. The
control panel has memorised the code and it quit automatically from programming.
- Repeat the same step if you need to program other transmitters.
Press one time
LEARNING OF THE PEDESTRIAN CODE
- Control panel ON, gate closed. the button A (SET) to enter into programming. LED DL10 starts
flashing. The programming phase begins.
- the button A press the button in the transmitter (for ex. the right button) and keep them pressed
until LED DL10 switches OFF. The control panel has memorised the code and it quit automatically from
programming.
- Repeat the same step if you need to program other transmitters.
Press one time
Keeping pressed
12 3 4 56 7 8910
!
CHANGE THE FACTORY SET-UP
TO AVOID NOT WANTED DRIVES
DIP-SWITCH SET-UP ONLY FOR TRANSMITTERS OG/02 AND OG/04
Only in the event that the dip-switches transmitters OG/02 or OG/04 are used, it is necessary to change the dip-
switch set-up before the programming, in order to change the factory set-up.
ATTENTION:before proceeding with the programming or the erasing of the transmitters it is
necessary to disconnect temporarily the antenna to avoid that the receiver during these phases
acquires other signals which may cause the uncorrect functionning of the system.
Connect the antenna as soon as finished.
CR/41 E
