Sentry SE series Manual de usuario
SE Series DVR Manual
SE Series DVR Manual
2
SE Series DVR Manual
3
Table of Contents
General
Safety Precautions 4
AboutThisManual 5
FrontPanelLayout 7
RearPanelLayout 8
MainScreenLayout 9
MouseControl 10
Operation using Front Panel Buttons/IR Remote Control 11
Settings and Configurations
1-CameraSettings 12
2-RecordSettings 13
3-AlarmDetectionSettings 14
4-MotionDetectionSettings 15
5-ScreenSettings 16
6-AudioSettings 17
7-SecurityProtectionSettings 17
8-TimeSetup 18
9-DwellTimeSetup 18
10-NetworkSettings 19
11-DNS/DDNSSetup 20
12-RS-485Setup 24
13-PTZCameraSetup 25
14-Video Search and Playback 26
15-VideoBackup 28
16-RemoteClientSoftware 30
Specifications 36
SE Series DVR Manual
4
CAUTION
RISK OF ELECTRICAL
SHOCK. DO NOT OPEN !
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER (OR BACK), NO USER
SERVICEABLE PARTS REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
Safety Precautions
The lightning flash with arrowhead symbol within an equilateral
triangle, is intended to alert the user that insulated dangerous Voltage
is contained within the product’s enclosure. This may be of sufficient
magnitude to constitute risk of electrical shock to persons opening the
enclosure.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operation and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE UNITS TO RAIN OR MOISTURE.
Attention: installation should be performed by qualified service
Personnel only, in accordance with the National Electrical Code or
applicable local codes.
Power Disconnect. Units with or without ON-OFF switches have
power supplied to the unit whenever the power cord is inserted into
the power source; however, the unit is operational only when the
ON-OFF switch is the ON position. The power cord is the main power
disconnect for all unites.
There are no serviceable parts for this unit, call for your agent for
details.
Warranty
and Service
SE Series DVR Manual
5
Before installing this embedded DVR, be sure to thoroughly review and follow the instructions in this User Manual. Pay
particular attention to the parts that are marked NOTICE.
Also, when connecting with external devices, first turn the power OFF and follow the instruction manual for appropriate
installation.
1. This document is intended for both the administrator and users of the SE DVR.
2. This manual contains information for configuring, managing and using the SE DVR.
3. To prevent fire or electrical shock, do not expose the product to heat or moisture
4. Be sure to read this manual before using the SE DVR.
5. For questions and technical assistance of this product, contact your local dealer.
►It is strongly recommended on installation of the DVR unit, that::
1. Check that electrical power is stable and meets our power requirements at the DVR installation site. Unstable
electricity can cause malfunction of the unit or even critically damage the unit.
2. Several chips on the main board of the DVR unit and hard disk drive inside the unit generate heat which must
be properly exhausted. Do not block the exhaust port (fan) on the left side of the unit and do not block the fresh
air in-take on the right side of the unit..
3. Locate the DVR in a well-ventilated place and do not put any heat-generating objects on the unit. If it is installed
in a 19 inch mounting rack together with other devices, please check that the built-in ventilation fan of the rack is
running properly.
About this Manual
Before Installing the DVR
SE Series DVR Manual
6
FCC Statement:
WARNING
This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference. (2) This device must accept any interference received including interference
that may cause undesired operation."
* Federal Communications Commission (FCC) Statement
WARNING
This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
* You are cautioned that changes or modifications not expressly approved by the party responsible for compliance
could void your authority to operate the equipment.
SE Series DVR Manual
7
USB 2.0 Port
for
Backup Drive
Quad Screen
Display
Channel 1
FullScreen Channel 3
FullScreen
Channel 2
FullScreen Channel 4
FullScreen
Key Lock
Function
Audio
On/Off
Auto Sequence
Mode
File
Backup
Setup
Menu Menu
Exit Playback
Record
Search/Select
Recordings
byTime
Decrease
Changeable
Menu Items
Increase
Changeable
Menu Item
s
Enter/
Accept
Changes
Move Down Menu/
Pause Playback
Move Up Menu/
Stop Playback
Reverse Playback/
Change Rewind
Speed
Choose Playback/
Change Playback
Speed
FRONT PANEL
SE Series DVR Manual
8
VGAOut
Port
RJ-45
LAN/Internet
Connector Audio In
Jack PS2 Mouse
Connector
Alarm In/
Alarm Out/
RS-485
Connections 12V DC/5A
Power In
Jac
k
Power
On/Off
Switch
Composite
Monitor/TV
BNCConnector
Audio Out
Jack
Up to 16 BNC
Camera Input
Connectors
RS-232
(Serial)
Connector
REAR PANEL
SE Series DVR Manual
9
Main Screen Layout
Recording icon
Overwrite
Motion
Alarm
Event (Motion / Alarm)
Video loss
Keypad lock *111111 is the default password
Live screen
SE Series DVR Manual
10
Mouse Control
○
1Screen display 1. With the mouse pointer on the desired camera in a
multi-camera screen, double-click the left mouse button
to full screen that particular camera
2. Double-click the left button on a full screen camera to
return to multi-camera screen
○
3Menu display 1. Single-click the right button to go to the menu OSD
2. Right-click in Menu to go to last OSD page displayed
(OSD = On Screen Display)
○
1To Select 1. Left-click on a specific menu item
2. Left-click on the value of item
3. Left-click on Exit to quit and save menu
4. Drag mouse from upper right corner to lower left corner
of a specific area on each camera to set the motion
detect area.
○
1 ○
2 ○
3
Tabla de contenidos
Otros manuales de DVR de Sentry
