Senso KSK2 Manual de usuario

DEVELOPEMENT

MANUAL

CMOS BARCODE SCANNER

Version: v2.0.10

KSK2

CONTENT

1Brief description.....................................................................................................1

2System Setting .......................................................................................................1

2.1 Setting code switch.................................................................................1

2.2 Switch for setting code data output......................................................1

2.3 Parameters setting....................................................................................1

2.4 Device information ..................................................................................2

2.4.1 Firmware version..............................................................................2

2.4.2 Unique identification code of device.............................................2

2.5 Custom product model............................................................................2

2.5.1 Set custom product model number ................................................2

2.5.2 Read custom product model number .............................................3

2.6 Restart.......................................................................................................3

3Communication setting..........................................................................................4

3.1 Interface settings......................................................................................4

3.1.1 UARTserial output ............................................................................4

3.1.2 UART serial port work settings .....................................................4

3.1.3 UART serial port baud rate setting ...............................................5

3.1.4 USB HID keyboard output..............................................................5

3.1.5 USB HID keyboard output Chinese settings ................................6

3.1.6 USB HID keyboard output interval time ......................................6

3.1.7 USB HID virtual keyboard numeric keyboard selection.............7

3.1.8 USB HID keyboard layout..............................................................7

3.1.9 USB virtual serial port output........................................................8

3.1.10 USB HID POS output.....................................................................9

3.2 Host command response mode ..............................................................9

3.3 Heartbeat query......................................................................................10

3.3.1 1 Heartbeat mode 1.........................................................................10

3.3.2 Heartbeat mode 2.....................................................................................10

4 Reading parameter settings....................................................................................11

4.1 Reading mode ........................................................................................11

4.1.1 Auto-sensing mode .........................................................................11

4.1.2 Continuous Mode............................................................................11

4.1.3 Manual mode(button/key mode)....................................................11

4.1.4 Command trigger mode .................................................................12

4.2 Automatic sensing sensitivity...............................................................12

4.3 Auto-sensing restart delay setting........................................................13

4.4 Auto-sensing button mode（for engine）...........................................13

4.5 Time of single reading .........................................................................14

4.6 The choice after reading is completed(In auto-sensing mode)..............15

4.7 Manual query of motion detection status.................................................15

4.8 Motion detection status is automatically sent..........................................16

4.9 Interval of barcode reading........................................................................16

5 Fill-Light and Aiming-Light..................................................................................18

5.1 Fill-Light.................................................................................................18

5.1.1 Mode of fill-light............................................................................18

5.1.2 Control method of fill-light...........................................................18

5.1.3 Set fill-light in level-mode............................................................19

5.1.4 Lighting brightness setting.............................................................19

5.1.5 Automatically turn on the fill light in dark environment.........20

5.1.6 Automatic fill light threshold..........................................................20

5.1.7 Time interval of auto fill-light on .................................................20

5.2 Aiming-Light ..........................................................................................21

5.2.1 Aiming-Light mode ........................................................................21

5.2.2 Aiming light flashes.......................................................................22

6 Prompt during output.............................................................................................23

6.1 Power-on prompt ...................................................................................23

6.2 Buzzer prompt when reading...............................................................23

6.3 Buzzer prompt when setting ................................................................23

6.4 LED Indicator light...............................................................................24

6.4.1 LED Indicator light ON/OFF........................................................24

6.4.2 Set the working level of the reading result indicator...............24

6.5 Fill-Light control signal output............................................................24

6.6 Power-on command prompt..................................................................25

6.7 Buzzer sound duration ..........................................................................25

6.8 Buzzer signal output mode...................................................................25

6.9 Buzzer frequency...................................................................................26

6.10 Buzzer loudness adjustment..................................................................26

6.11 Buzzer working level............................................................................27

7 Data editing.............................................................................................................28

7.1 Remove original data settings..............................................................28

7.1.1 Example 1 Remove the first 20 bytes of user data..................28

7.1.2 Cancel remove the previous data.................................................28

7.1.3 Example 2 Remove the 20 bytes of data after the data..........29

7.1.4 Cancel to remove the data of end...............................................29

7.2 Only output data at both ends(remove middle data)........................29

7.2.1 Example 1 Only output the first 20 bytes of data .....................30

7.2.2 Cancel only output the first end data ...........................................30

7.2.3 Example 2 Only output the last 20 bytes of data ......................30

7.2.4 Cancel only output backend data...................................................31

7.3 Add prefix..............................................................................................31

7.3.1 Add prefix example1 example2......................................................31

7.3.2 Clear prefix .......................................................................................32

7.4 Add suffix ..............................................................................................32

7.4.1 Add suffix example1 example2 ......................................................32

7.4.2 Clear suffix........................................................................................33

7.5 Data filtering rule settings....................................................................33

7.5.1 example 1 Filter a0 in the data.....................................................33

7.5.2 Clear filter rules ...............................................................................34

7.6 CRC Check ............................................................................................34

7.7 Terminator...............................................................................................35

7.8 Barcode type character output .............................................................35

7.9 Case output settings ..............................................................................36

7.10 Prohibit URL output..............................................................................36

8 Barcode reading configuration...............................................................................37

8.1 All barcode configurations....................................................................37

8.2 Single barcode configuration................................................................37

8.2.1 CODE 128.......................................................................................38

8.2.2 GS1_128 ..........................................................................................39

8.2.3 CODE39...........................................................................................39

8.2.4 Interleaved 2 of 5..........................................................................41

8.2.5 Straight 2 of 5 industrial ..............................................................42

8.2.6 Straight 2 of 5 IATA.....................................................................43

8.2.7 Matrix 2 of 5 .................................................................................43

8.2.8 Grid Matrix .....................................................................................44

8.2.9 CODE 93.........................................................................................45

8.2.10 CODE 11.........................................................................................45

8.2.11 CODABAR......................................................................................46

8.2.12 TELEPEN........................................................................................47

8.2.13 MSI ..................................................................................................48

8.2.14 GS1 DataBar(RSS) .........................................................................48

8.2.15 PDF417............................................................................................49

8.2.16 MICRO PDF...................................................................................50

8.2.17 Aztec Code......................................................................................50

8.2.18 MaxiCode.........................................................................................51

8.2.19 MICRO QR.....................................................................................51

8.2.20 Han Xin code .................................................................................51

8.2.21 China Post (Hong Kong 2 of 5) .................................................52

8.2.22 Data Matrix.....................................................................................52

8.2.23 NEC 2 of 5....................................................................................53

8.2.24 UPC-A..............................................................................................54

8.2.25 UPC-E0 & UPC-E1 .......................................................................55

8.2.26 EAN/JAN-13....................................................................................57

8.2.27 EAN/JAN-8......................................................................................59

Appendix 1 Barcode Type Output Character List..................................................61

Appendix 2 Digital Code ..........................................................................................61

Appendix 3 CODE39 FULL ASCII Correspondence Table..................................63

Appendix 4 Test Barcode..........................................................................................64

1Brief description

This manual mainly provides various function setting commands for barcod

e reading equipment. By familiarizing with the introduction of various function

commands in this manual, users can change the function parameters of the ba

rcode reading device by scanning the setting code or sending setting commands

through the interface. The product has provided parameter configuration suitab

le for most common application functions at the factory. In most cases, the us

er can put it into use without adjustment. The factory default is UART serial

port output, and the default baud rate is 9600.

REMARK：

(1) All setting parameters with * are system default parameters;

(2) The CRC included in the commands in this document uses CRC16_XMOD

EM, polynomial x16+x12+x5+1 (0x1021), the data is reversed to MSB First, a

nd the data format is a string format configuration. For example, a command i

s: $xxxxxx-yyyy, the 4 digits of yyyyare the check code, and $xxxxxx-the 8 d

igits are the content for calculating the checksum.

2System Setting

2.1Setting code switch

This function is whether the user can set up the device by scanning the settin

g code. After the setting code is turned off, the parameter configuration cannot be

performed by scanning the setting code. The setting code is regarded as a normal

barcode; after the setting code is turned on, the parameter configuration can be p

erformed by scanning the setting code. The default is that the switch is on

Command for off setting code switch：$010000-525C

Command for on setting code switch：$010001-616D

Note: These two commands can only be set by sending commands throug

h UART and other interfaces

2.2Switch for setting code data output

This function is whether the user outputs the scanned setting code content thr

ough the UART interface.

2.3Parameters setting

Rest to factory default

Restore all parameters to the factory default, the device will automatically rest

art after this operation.

$010100-24E8

（*No output）

$010101-17D9

（Output）

$010200-BF34

（Reset）

2.4Device information

2.4.1 Firmware version

2.4.2 Unique identification code of device

After reading successfully, the device will return a string of 12 bytes to the h

ost. Can be used to identify products.

2.5Custom product model

2.5.1 Set custom product model number

Under this function, the user can name the product model number by himself, an

d then it can be read by the read command. The steps to set a custom product model

are as follows:

(1) Set the custom product model number by scan following setting codes：

$010300-C980

（Output firmware version）

$0103A0-26B8

Read the unique code of the device (12 characters)

$010204-73F0 Enter the setting state of custom product model name

（2）Make a non-setting QR code of a customized product model number and sca

n the code. The buzzer sounds three times to indicate the setting is successful, an

d the buzzer sounds once to indicate the setting failed. as follows:

Custom product model number test code, scan the following code after setting

in step (1), the custom product model will be set to CUSTOM PRODUCT MOD

EL TEST, scan 2.5.2 to read the command code of the custom product model or

send a command It can be read out.

Notice:

a. The total characters of the customized product model number cannot excee

d 100 bytes, otherwise the setting will fail;

b. After the setting fails, you need to restart the setting from step (1);

c. After the setting is successful, if you want to modify the setting model, dir

ectly restart the setting from step (1), and the original setting model will be cleare

d; d. After the setting is successful, restoring the factory settings will also retain

the set model number.

2.5.2 Read custom product model number

Read the customized product model number set by the user

2.6 Restart

The device will restart immediately after scanning the setting code or sending

the setting command.

$010205-40C1 （read customized product model number）

$010500-EE19 （Restart）

3Communication setting

3.1Interface settings

The factory default is UART interface output. If you need other interface

output, scan the enable code of the corresponding interface to switch, the settin

g will not take effect immediately, you need to manually restart the device to

take effect, and the set interface will not be restored after scanning and restori

ng the factory settings. Keep the original settings unchanged.

3.1.1 UARTserial output

If the data output interface is switched to UART serial output, it will not

take effect immediately, and it needs to be manually restarted to take effect.

The default output configuration of the serial port is: baud rate-9600bps, s

top bit-1 bit, data bit-8 bits, parity bit-none, no flow control. The baud rate ca

n be changed according to the setting in section 3.1.3.

3.1.2 UART serial port work settings

By default, the UART serial port keeps sending no matter what interface o

utput mode it is in. The receiving will be turned off in the USB virtual serial

port output mode, and it will be turned on in other modes. It can be set to

only use the serial port to transmit data in the UART serial port output mode.

(Note: The default parameter of v4.x.39, v6.0.9 and higher version is "only

work in UART serial output mode", the default parameter before v4.x.39, v6.

0.9 is "no matter what interface Keep working in output mode".)

$020003-C9EF

UART serial output

3.1.3 UART serial port baud rate setting

The baud rate of the serial port is adjustable, and the default bit is 9600, whi

ch will take effect immediately after setting.

3.1.4 USB HID keyboard output

$020503-75AA（Baud rate2400）

$020504-EC3D（Baud rate4800）

$020505-DF0C （* Baud rate9600）

$020506-8A5F（Baud rate19200）

$020507-B96E （Baud rate38400）

$020508-A950（Baud rate57600）

$020509-9A61（Baud rate115200）

$020E01-51BD

Keep working regardless of interface out

put mode

$020E00-628C

*Only work in UART serial port output

mode

Tabla de contenidos

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario