- 1-
SAFETY PRECAUTIONS
* SEE BOTTOM OF UNIT FOR GRAPHIC SYMBOLS *
This product contains a low
power laser device.
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH
CANADIAN ICES-003.
WARNING: T O R E D U C E T H E R I S K O F
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE. DO NOT PLACE OBJECTS FILLED WITH
LIQUIDS ON OR NEAR THIS UNIT.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS
INCORRECTLY REPLACED. REPLACE ONLY WITH THE
SAME OR EQUIVALENT TYPE.
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN.
AVOID EXPOSURE TO BEAM.
The lightning flash with an arrowhead symbol,
within the equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous
voltage” within the product's enclosure that may be
of sufficient magnitude to cause an electric shock.
The exclamation point within the equilateral
triangle is intended to alert the user to the presence
of important operating and maintenance (servicing)
instructions in this owner’s manual.
WARNING: Should any trouble occur, disconnect the AC power adapter and refer servicing to a qualified technician.
On Placement
• Donotusetheunitinplacesthatareextremelyhot,cold,dusty,orhumid.
• Placetheunitonaatandevensurface.
• Donotrestricttheairowoftheunitbyplacing it in a place with poor air ow,bycoveringitwithacloth,orbyplacingiton
carpeting.
• Toavoidmagnetized,donotplacetheunitnearspeakerormagnet.
• Donotusethisunitindirectsunlightorleavetheunitinaclosedautomobile(oryacht,etc)whereitwouldbeexposedtohigh
temperatures above 104°F (40°C).
• NonakedamesourcessuchaslightedcandlesshouldbeplacedontheACpoweradapterandmainunit.
• The apparatus shall not be exposed to dripping or splashing and that no objects lled with liquids, such as vases, shall be
placed on apparatus.
On Safety
• WhenconnectingordisconnectingtheACpoweradapter,griptheplugandnotthecorditself.Pullingthecordmaydamageit
andcreateahazard.
• Whenyouarenotgoingtousetheunitforalongperiodoftime,disconnecttheACpoweradapter.
On Condensation
• Whenleftinaheatedroomwhereitiswarmanddamp,waterdropletsorcondensationmayforminsidetheunit.Whenthereis
condensation inside the unit, the unit may not function normally. Let the unit stand for 1 to 2 hours before turning the power on,
or gradually heat the room and allow the unit to dry before use.
Ventilation Warning
• Donotblocktheventilationopeningsorholes.(Iftheventilationopeningsorholesareblockedbyanewspaperorcloth,etc.,the
heat may not be able to get out.)
• Donotoperatetheunitinaconnedspace,suchasabookcaseorbuilt-incabinet,allowabout4inch(10cm)offreespaceall
around the unit for adequate ventilation.
Rating Plate Location
• Theratingplateislocatedonthebottomofunit.
FCC Statements
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
