Senix GTBCU4QL-M Manual de usuario
4-Cycle 1.9 cu in. (31 cc) Engine Gasoline
Powered Grass Trimmer/Brush Cutter 2 in 1
Model: GTBCU4QL-M
Operator's manual
TM
For customer support, please call 1-800-261-3981 or send email to:
SAVE THIS MANUAL FOR FUTURE REFERENCE
EN - 2 WWW.SENIXTOOLS.COM
4
2
1
3
8
6
5
9
7
15
16
18
17
12
19
13
11
10
14
1
23
Mount Bracket
Mounting Disc
Blade
Washer
Floating Disc
Locknut
Screw
Tab
Cutting Head Shield
3 - EN
WWW.SENIXTOOLS.COM
4
6
98
7
5
Mounting Disc
Cutting Head
Upper Fixed Cover
Tighten
Loosen
Knob
Lower Fixed Cover
Locating Hole
Low Shaft
Coupler
Knob
Locating Button
Oil Fill Plug
O-Ring
Oil Fill Hole
Handle Support
EN - 4 WWW.SENIXTOOLS.COM
滚滚长江东逝水
滚滚长江东逝水
Starter rope
10
13
15
12
14
On/Off Switch
Throttle Lockout
Choke Button
Throttle Control
Primer Bulb
Starter Rope
Base of Fuel Tank Spout
11
5 - EN
WWW.SENIXTOOLS.COM
17
19
19
21
21
18
18
20
20
Bump Knob
Holding Slot
Split Wall
Oil Visible on First Thread
16
Eyelet
Spring
Washer
Spool Retainer
Holding Slots
Eyelet
Tabs
EN - 6 WWW.SENIXTOOLS.COM
22
24
23
Idle Speed Screw
0.60mm - 0.80mm
0.025in. - 0.031in.
Primer Bulb
Cover Rotary Knob
Air Filter Housing Air Filter Cover
Air Filter
7 - EN
WWW.SENIXTOOLS.COM
TABLE OF CONTENTS
SAFETY & INTERNATIONAL SYMBOLS ...........................7
SAFETY INSTRUCTIONS...................................................8
KNOW YOUR UNIT............................................................13
SPECIFICATIONS*............................................................13
ASSEMBLY.........................................................................13
OIL AND FUEL...................................................................14
OPERATION.......................................................................15
MAINTENANCE..................................................................17
TROUBLESHOOTING.......................................................20
PARTS................................................................................21
WARRANTY.......................................................................23
SAFETY & INTERNATIONAL
SYMBOLS
Explanation of Safety & international symbols describes
safety and international symbols and pictographs that may
appear on this product. Read the operator’s manual for
complete safety, assembly, operating and maintenance and
repair information.
This graphic accompanied by the words
WARNING, DANGER OR CAUTION calls
attention to an act of a condition which can
lead to SERIOUS INJURY.
Read the operator’s manual(s) and follow all
warnings and safety instructions. Failure to do
so can result in serious injury to the operator
and/or bystanders.
Always wear eye protection, ear protection and
head protection meeting ANSI Z87.1 standards.
Wear gloves.
Wear foot protection.
Beware of foot injury by cutting attachment.
Keep 15 meters or 50 feet away from any other
person.
Beware of objects ung by cutting
attachments.
Never use without properly mounted protection
guard.
Beware of objects ung by cutting
attachments.
Never use without properly mounted protection
guard.
Don’t install or use any type of blade on the unit
displaying this symbol.
Bystander sound pressure level: 75dB(A).
Maximum permitted revolutions of the cutting
head.
Maximum permitted revolutions of the blade.
75dB(A)
MEASURED AT 50FT. (15M)
PER ANSI B175.3
5700
5700
EN - 8 WWW.SENIXTOOLS.COM
SAFETY INSTRUCTIONS
WARNING!
Signals a SERIOUS hazard.
Failure to obey a safety WARNING
symbol CAN result in serious injury
to yourself or to others.
NOTE:
Advises you of information or
instructions vital to the operation or
maintenance of the equipment.
WARNING!
Crude oil, gasoline, diesel fuel
and other petroleum products can
expose you to chemicals including
toluene and benzene, which are
known to the State of California to
cause cancer and birth defects or
other reproductive harm. These
exposures can occur in and around
oil elds, reneries, chemical plants,
transport and storage operations
such as pipelines, marine terminals,
tank trucks and other facilities and
equipment. For more information
go to: www.P65Warnings.ca.gov/
petroleum.
WARNING!
CALIFORNIA PROPOSITION 65
This product contains a chemical
known to the state of California to
cause cancer, birth defects or other
reproductive harm.
Read the operator’s manual and
follow all warnings and safety
instructions. Failure to do so
can result in serious injury to the
operator and/or bystanders.
SAFETY WARNINGS
1. Proper safety precautions must
be observed. Like all power
equipment this unit must be
handled carefully. DO NOT
EXPOSE YOURSELF OR
OTHERS TO DANGER. Follow
these general rules. Do not
permit others to use this unit
unless they are thoroughly
responsible and have read, and
understood the string trimmer
manual and are trained in its
operation.
2. Always wear heavy, long pants,
boots, gloves, and a long-sleeve
shirt. Do not wear loose clothing,
jewelry, short pants, sandals, or
go barefoot. Secure hair so it is
above shoulder level.
3. Inspect unit before each use.
Replace damaged parts.
Check for fuel leaks. Make
sure all fasteners are in place
and secure. Replace cutting
attachment parts that are
cracked, chipped, or damaged in
any way. Make sure the cutting
9 - EN
WWW.SENIXTOOLS.COM
7. Do not operate the unit in
insufcient lighting conditions.
8. Do not operate this unit when
tired, ill, or under the inuence of
alcohol, drugs, or medication.
9. Always use proper handles when
trimming.
10. Do not smoke while lling tank.
11. Do not ll fuel in an enclosed
room or near open ames.
Ensure adequte ventilation.
12. Always store fuel in a properly
marked container that is
approved by local codes and
ordinances for such usage.
13. Never remove the fuel tank cap
while the engine is running.
14. Do not operate the unit inside
a closed environment, such as
a room or building; breathing
carbon monoxide from exhaust
fumes can kill.
15. Never attempt to make engine
adjustments while the unit is
running. Always make engine
adjustments with the unit resting
on a at, clear surface.
16. Do not use the unit if it is
damaged or poorly adjusted.
Never remove the unit’s guard.
Serious injury to the operator or
bystanders could result as well
as damage to the machine.
17. Clear the area to be cut before
attachment is properly installed
and securely fastened. Be sure
the cutting attachment shield
is properly attached and in the
position recommended by the
manufacturer. Use only exible,
nonmetallic line recommended
by the manufacturer. Never use,
for example, wire or wire-rope,
which can break off and become
a dangerous projectile.
4. DO NOT USE any attachment
with this power head other than
the ones recommended by the
manufacturer. Serious injury to
the operator or bystanders could
result as well as damage to the
machine.
5. The handles shall be mounted
in accordance with the
manufacturer’s instructions.
Do not attach any blade to a
unit without proper installation
of all required parts. Failure
to use the proper parts can
cause the blade to y off and
seriously injure the operator and/
or bystanders. Discard blades
that are bent, warped, cracked,
broken, or damaged in any way.
Use a sharp blade. A dull blade
is more likely to snag and thrust.
6. Keep the handles free from oil
and fuel.
EN - 10 WWW.SENIXTOOLS.COM
each use. Remove all objects
such as rocks, broken glass,
nails, wire, or string, which can
be thrown or become entangled
in the cutting attachment. Clear
the area of children, bystanders
and pets. At a minimum, keep
all children, bystanders and pets
outside a 15 m (50 ft) radius;
outside the 15 m (50 ft) zone,
there is still a risk of injury from
thrown objects. Bystanders
should be encouraged to wear
eye protection.
18. Never leave the unit unattended
while the engine is running.
19. Do not use this unit for any job
other than those for which it is
intended as described in this
manual.
20. Maintain rm footing and
balance. Do not over-reach.
Keep cutting attachment below
waist level. Maintain all parts of
your body away from the rotating
cutting attachment and hot
surfaces.
21. Do not use this type of unit for
sweeping away debris.
22. Use nylon cutting head which
is free of damage. If a stone
or any other obstacle is hit,
stop the engine and check the
nylon cutting head. A broken or
unbalanced nylon cutting head
must never be used.
23. FOLLOW INSTRUCTIONS for
assembling and operation.
24. Do not store the unit in a closed
area where fuel vapors can
reach an open ame from hot
water heaters, furnaces, etc.
Store in a locked, well ventilated
area only.
25. Ensure safe and proper
performance of your unit. Please
only use original accessories.
The use of any other
accessories or attachments
may cause a potential hazard or
injury to the user, damage to the
unit, and void the warranty.
26. If the unit will not be used for
a long time, clean the unit
completely, especially the fuel/oil
tank, its surroundings, and the
air lter.
27. When refueling, stop the engine
and conrm that it is cooled
down. Never refuel when the
engine is running or hot. When
gasoline spills, be sure to wipe
it up completely and dispose of
those materials before starting
the engine.
28. Mix and pour fuel outdoors
where there are no sparks and
flames. Slowly remove the fuel
Tabla de contenidos
Idiomas:
Otros manuales de Recortadora de Senix
Senix
Senix GTE2.5-L-EU Manual de usuario
Senix
Senix HTPX2-M Manual de usuario
Senix
Senix HTE3.8-L Manual de usuario
Senix
Senix GTSX5-M-0 Manual de usuario
Senix
Senix GTC4QL-L Manual de usuario
Senix
Senix HT4QL-L Manual de usuario
Senix
Senix HTX2-M Manual de usuario
Senix
Senix GTS4QL-M2 Manual de usuario
Senix
Senix GTX2-M Manual de usuario
Senix
Senix HTX5-M Manual de usuario
