Senco SFT10XP Manual de usuario

Operating Instructions

SFT10XP

Fine Wire Stapler



Employer must enforce compliance

with the safety warnings and all

other instructions which accompany

this tool as shipped from the

manufacturer.

Keep this manual available for use

by all people assigned to the use of

this tool.

For personal safety and proper

operation of this tool, read and

understand all of these instructions

carefully.



Employer’s Responsibilities....................... 2

Safety Warnings ........................................ 3

Tool Use .................................................... 7

Maintenance.............................................. 9

Troubleshooting....................................... 10

Accessories ............................................. 10

Technical Specications.......................... 11

Fastener Specications ........................... 11

Limited Warranty ..................................... 12





 Read and understand tool labels

and manual. Failure to follow

warnings could result in DEATH

or SERIOUS INJURY.



 Use safety equipment. Always

wear ANSI Z87.1 safety glasses

with permanently attached side

shields. Dust mask, non-skid

safety shoes, hard hat, or hear-

ing protection must be used for

appropriate conditions. Failure

to do so could result in personal

injury.

Personal Safety

 Stay alert, watch what you are

doing, and use common sense

when operating a power tool. Do

not use tool while tired or under

the inﬂuence of drugs, alco-

hol, or medication. A moment

of inattention while operating

power tools may result in serious

personal injury.



 Never use tool in an explosive

atmosphere or in the presence

of combustible materials such as

ﬂammable liquids, gases or dust.

 Never use oxygen, carbon

dioxide or any other bottled gas

as a power source for this tool;

the tool will explode and cause

serious injury.

 Always remove nger from trig-

ger when not driving fasteners.

Never carry the tool with nger

on or under trigger.

 





 Always assume the tool con-

tains fasteners. No horseplay.

Respect the tool as a working

implement.

 Keep tool pointed away from

yourself and others and connect

air to tool.

 Tools shall be operated at the

lowest pressure needed for the

application. This will reduce

noise levels, part wear, and

energy use.



 Drive fasteners into work surface

only; never into materials too

hard to penetrate.

 Do not drive fasteners on top of

other fasteners or with the tool

at too steep of an angle; the

fasteners can ricochet and hurt

someone.

 Do not drive fasteners close to

the edge of the work surface.

The workpiece is likely to split

and the fastener could ﬂy free or

ricochet and hit someone.

 Tool may eject a fastener when

connected to air supply; there-

fore, remove all fasteners from

tool before connecting air.

 Never use tool if trigger or

springs have become inopera-

ble, missing or damaged. Do not

tamper with or remove trigger or

springs.

 Disconnect tool from air before

doing tool maintenance, clearing

a jammed fastener, leaving work

area, moving tool to another

location, or handing the tool to

another person.



 Make sure all screws and caps

are securely tightened at all

times. Make daily inspections for

free movement of trigger. Never

use the tool if parts are missing

or damaged.

 Never use a tool that leaks air or

needs repair.

 Use only parts, fasteners, and

accessories recommended or

sold by SENCO. Do not modify

tool without authorization from

SENCO.

 Use only clean, dry, regulated

compressed air at recommended

pressure.

200 psig

13.7 bar

 Do not connect tools to air pres-

sure that potentially exceeds 200

psig or 13.7 bar.

 Air compressors used to supply

compressed air to this tool must

comply with requirement ANSI/

ASME B 19.1–1995 (U.S.),

“Safety Standard For Air Com-

pressor Systems.”

 Air hose must have a minimum

working pressure rating of 150

psig (10.3 bar) or 150% of the

maximum pressure produced in

the system, whichever is higher.



 The tool and air supply hose

must have a hose coupling such

that all pressure is removed from

the tool when the coupling joint

is disconnected.

 Do not load fasteners with trig-

ger depressed.

(1) Read and understand tool labels and manual. Failure to follow

warnings could result in DEATH or SERIOUS INJURY. (2) Operators and

others in work area MUST wear safety glasses with side shields. (3) Keep fingers AWAY from trigger

when not driving fasteners to avoid accidental firing. (4) See manual for triggering instructions.

(5) NEVER point tool at yourself or others in work area. (6) NEVER use oxygen or other bottled gases. Explosion may occur.

(7) MAX AIR PRESS. 120 PSI (8.3 BAR)

 Do not use tool without danger

label on tool. If label is missing,

damaged or unreadable, contact

your SENCO representative to

obtain a new label.

 Always place yourself in a rmly

balanced position when using or

handling the tool.

 For information on the “SENCO

Safety First Program,” contact

your SENCO representative.



 Read section titled “Safety

Warnings,” before using tool.



①Push latch.

②Slide rail open.

 Connect air supply and lay strip

of staples into magazine.

Use only genuine SENCO fas-

teners (see Parts Chart).

 -



 Push rail forward until it latches.



①Position tool against work

surface.

②Pull trigger.

 



-











 Disconnect air supply.

①Depress latch.

②Slide rail open.

 Remove staples.

 Remove jammed fastener.

 Connect air supply and lay strip

of staples into magazine.

Use only genuine SENCO fas-

teners (see Parts Chart).

 



 Push rail forward until it latches.





 This tool is equipped with a drive

rate adjustment to adjust the

speed.

 Rotate the screw, not more than

three turns, counter-clockwise

(Q) to increase the drive rate.

Rotate the screw clockwise (P),

not more than three turns, to

slow the drive rate.

 For single shot operation, pull

trigger only partially. For auto-

matic operation, pull trigger fully.





 Repairs other than those

described here should be per-

formed only by trained,

qualified personnel.

 Read section titled “Safety

Warnings” before maintaining

tool.

 All screws should be kept tight.

Loose screws result in unsafe

operation and parts breakage.

 With tool disconnected, make

daily inspection to assure free

movement of trigger. Do not use

tool if trigger sticks or binds.

 Squirt Senco pneumatic oil (5 to

10 drops) into the air inlet daily

(depending on frequency of tool

use). Other oils may damage

O-rings and other tool parts.

 Wipe tool clean daily and

inspect for wear. Use non-ﬂam-

mable cleaning solutions only if

necessary.

 DO NOT SOAK.

 Caution: Such solutions may

damage O–rings and other tool

parts.





Air leak near top of tool /

Sluggish operation



Verify air supply /

Tighten screws or install Firing

System Kit Ⓐ.



Air leak near bottom of tool /

Poor return. 

Clean tool / tighten screws or install

Piston Stop Kit Ⓑ.

3

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual