Senco RoofPro 445XP Manual de usuario

Operating Instructions

RoofPro 445XP

Coil Roofing Nailer



Employer must enforce compliance

with the safety warnings and all other

instructions which accompany this

tool as shipped from the manufacturer.

Keep this manual available for use

by all people assigned to the use of

this tool.

For personal safety and proper

operation of this tool, read and

understand all of these instructions

carefully.





EmployEr’srEsponsibilitiEs......................... 2

safEty Warnings ........................................ 3

tool UsE .................................................... 7

maintEnancE ............................................... 9

troUblEshooting....................................... 10

accEssoriEs.............................................. 10

options .................................................... 10

tEchnical spEcifications ............................11

spEcifications ............................................11

limitEd Warranty...................................... 12





 Read and understand tool labels

and manual. Failure to follow

warnings could result in DEATH

or SERIOUS INJURY.



 Use safety equipment. Always

wear ANSI Z87.1 safety glasses

with permanently attached side

shields. Dust mask, non-skid

safety shoes, hard hat, or hear-

ing protection must be used for

appropriate conditions. Failure

to do so could result in personal

injury.



 Stay alert, watch what you are

doing, and use common sense

when operating a power tool. Do

not use tool while tired or under

the inﬂuence of drugs, alco-

hol, or medication. A moment

of inattention while operating

power tools may result in serious

personal injury.



 Never use tool in an explosive

atmosphere or in the presence

of combustible materials such as

ﬂammable liquids, gases or dust.

 Never use oxygen, carbon

dioxide or any other bottled gas

as a power source for this tool;

the tool will explode and cause

serious injury.

RoofPRO

 Always remove nger from trig-

ger when not driving fasteners.

Never carry the tool with nger

on or under trigger. Tool will eject

a fastener if the workpiece con-

tact (safety element) is bumped.

RoofPRO

 Always assume the tool contains

fasteners. No horseplay. Respect

the tool as a working implement.

 Keep tool pointed away from

yourself and others and connect

air to tool.

 Tools shall be operated at the

lowest pressure needed for the

application. This will reduce

noise levels, part wear, and

energy use.



RoofPRO

 Drive fasteners into work surface

only; never into materials too

hard to penetrate.

RoofPRO

 Do not drive fasteners on top of

other fasteners or with the tool at

too steep of an angle; the fasteners

can ricochet and hurt someone.

RoofPRO

 When using tool, care should be

taken due to possibility of tool

recoil after a fastener is driven.

If workpiece contact (safety

element) is unintentionally al-

lowed to re-contact work surface

following a recoil, an unwanted

fastener will be driven. Therefore,

allow tool to recoil completely

off work surface after a fastener

is driven to avoid this condition.

Do not push workpiece contact

(safety element) on work sur-

face until a second fastener is

desired.

RoofPRO

 Do not drive fasteners close to

the edge of the work surface.

The workpiece is likely to split

and the fastener could ﬂy free or

ricochet and hit someone.

RoofPRO

 Never use any part of the tool

(i.e., the cap or mainbody ) as a

hammer. The tool may activate or

become damaged and result in

an unsafe condition.

RoofPRO

 Keep hands and other body

parts away from the area shown

in the circle to avoid possible

injury during operation.

RoofPRO

 Tool may eject a fastener

when connected to air supply;

therefore,

jremove all fasteners from tool

before kconnecting air.









RoofPRO

 Never use tool if workpiece con-

tact (safety element), trigger or

springs have become inoperable,

missing or damaged. Do not

tamper with or remove workpiece

contact (safety element), trigger,

or springs.

RoofPRO

 Disconnect tool from air before

doing tool maintenance, clearing

a jammed fastener, leaving work

area, moving tool to another

location, or handing the tool to

another person.

RoofPRO

 Make sure all screws and caps

are securely tightened at all

times. Make daily inspections

for free movement of trigger and

workpiece contact (safety ele-

ment). Never use the tool if parts

are missing or damaged.

RoofPRO

 Store idle tools out of reach of mi-

nors and other untrained persons.

Tools are dangerous in the hands

of untrained users.

 Use only parts, fasteners, and ac-

cessories recommended or sold by

SENCO. Do not modify tool without

authorization from SENCO.

 Use only clean, dry, regulated

compressed air at recommended

pressure.

200 psig

13.7 bar

 Do not connect tools to air pressure

that potentially exceeds 200 psig

or 13.7 bar.



 Air compressors used to supply

compressed air to this tool must

comply with requirement ANSI/

ASME B 19.1–1995 (U.S.),

“Safety Standard For Air Com-

pressor Systems.”

 Air hose must have a minimum

working pressure rating of 150

psig (10.3 bar) or 150% of the

maximum pressure produced in

the system, whichever is higher.

RoofPRO

 The tool and air supply hose

must have a hose coupling such

that all pressure is removed from

the tool when the coupling joint

is disconnected.

RoofPRO

 Do not load fasteners with trigger

or workpiece contact (safety ele-

ment) depressed.

RoofPRO

 Never use a tool that leaks air or

needs repair.

(1) Read and understand tool labels and manual. Failure to follow

warnings could result in DEATH or SERIOUS INJURY. (2) Operators and

others in work area MUST wear safety glasses with side shields. (3) Keep fingers AWAY from trigger

when not driving fasteners to avoid accidental firing. (4) See manual for triggering instructions.

(5) NEVER point tool at yourself or others in work area. (6) NEVER use oxygen or other bottled gases. Explosion may occur.

(7) MAX AIR PRESS. 120 PSI (8.3 BAR)

 Do not use tool without danger

label on tool. If label is missing,

damaged or unreadable, contact

your SENCO representative to

obtain a new label.

RoofPRO

 Always place yourself in a rmly

balanced position when using or

handling the tool.

 For information on the “SENCO

Safety First Program,” contact

your SENCO representative.



 Read section titled “Safety Warn-

ings,” before using tool.

RoofPRO



 jSqueeze the gate latch and

lift open gate.

 kOpen Magazine.

 Lift and shift nail disk to accept

different length nails.

 Reference points on

magazine coincide with nail

lengths.

RoofPRO

 Place the nail coil in the maga-

zine.

 Always adjust magazine to

provide fasteners with correct

driving alignment. Failure to ad-

just the magazine will cause the

fasteners to not drive properly

and could result in injuries to

yourself and others.

RoofPRO

 Close magazine cover and gate.

Make sure gate is fully latched.

RoofPRO

 With a Contact-Actuation

(“Dual-Action”) trigger, nails can

be driven two ways:

AjPosition workpiece contact

(safety element) against work

surface then

kpull trigger.

RoofPRO

BjPull trigger, then

kpush workpiece contact

(safety element) against work

surface. Each time you push

the workpiece contact (safety

element) against the work

surface, a fastener is driven.

This mode of operation is

preferred when you desire

high production, rapid fastener

placement.

RoofPRO

 With a Sequential Actuation

(Restrictive) trigger, fasteners

can only be driven one way.

 jPosition workpiece contact

(safety element) against work

surface, then

kpull trigger.

This mode of operation is help-

ful when you require precise

fastener placement.





































RoofPRO





 First disconnect the air supply.

 Using your thumb or index

nger, rotate wheel to adjust the

Depth Control workpiece contact

(safety element) to achieve

desired depth.

RoofPRO



 Disconnect air supply.

RoofPRO

 Press down on the gate latch

and lift open gate.

 Extract bent nail from rear of

guide body.

RoofPRO



 Insert a rod and push the point

of the nail back up and into the

guide body bore.

 Extract the nail with pliers or, if

the nail is loose, turn the tool

upside-down and shake it out.





 Repairs other than those

described here should be per-

formed only by trained, qualied

personnel. Contact SENCO for

information at:

1-800-543-4596.

 Read section titled “Safety Warn-

ings” before maintaining tool.

RoofPRO

 All screws should be kept tight.

Loose screws result in unsafe

operation and parts breakage.

RoofPRO

 With tool disconnected, make

daily inspection to assure free

movement of workpiece contact

(safety element) and trigger. Do

not use tool if workpiece contact

(safety element) or trigger sticks

or binds.

 Squirt Senco pneumatic oil (5 to

10 drops) into the air inlet twice

daily (depending on frequency

of tool use). Other oils may dam-

age O-rings and other tool parts.

RoofPRO

 Wipe tool clean daily and inspect

for wear. Use non-ﬂammable

cleaning solutions only if neces-

sary.

 

  Such solutions may

damage O–rings and other tool

parts.









Air leak near top of tool /

Sluggish operation.



Verify air supply / Tighten screws or

install Repair Kit YK0865.





Air leak near bottom of tool / Poor

return. 

Clean tool / Tighten screws or install

Repair Kit YK0865.



Manuales populares de Pistola de clavos de otras marcas

Performance Tool

Performance Tool M643 Manual de usuario

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Grizzly

Grizzly G1847 Manual de usuario

Ryobi

Ryobi R18N18G Manual de usuario

Black & Decker

Black & Decker 492848-00 Manual de usuario

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Manual de usuario

Metabo HPT

Metabo HPT NR 3690DC Manual de instrucciones

Surtek

Surtek CN650 Dimensiones y guía de instalación

Makita

Makita GF600 Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Freeman

Freeman P50LSLW Manual de usuario

Aicon PRO

Aicon PRO DAC4507 Manual de usuario

DAJ

DAJ XR150A Manual de usuario

Makita

Makita AN923 Manual de usuario

Grizzly

Grizzly T20644 Manual de usuario

Black & Decker

Black & Decker 90514937 Manual de usuario

Alfamacchine

Alfamacchine Minigraf 4 Manual