SEM Breaktank Manual de usuario

The specialist for safe & clean swimming water

SEM Waterbehandeling

B.V.

De Run 4420

5503 LR Veldhoven

Netherlands

Telefoon: +31 (0) 40 257 03 40

[email protected]

www.semwaterbehandeling.nl

Handbook

SEM Compact Breaktank

with Level Control

Breaktank

6-2015

art.nr.:2502925

EN1717/EN13077

BREAKTANK HA N D B O O K

06/2015 V4.0 1

Content

FOR INFORMATION .......................................................................................................................................... 2

1. INTRODUCTION ............................................................................................................................................ 4

2. CONTROL ...................................................................................................................................................... 5

2.1 DISPLAY AND BUTTONS ........................................................................................................................................ 5

2.2. SERVICE MENU .................................................................................................................................................. 7

2.3 SETUP MENU ..................................................................................................................................................... 8

2.4 SCHEMATIC REPRESENTATION OF MENU STRUCTURE ................................................................................................ 10

3. INSTALLATION GUIDELINES ........................................................................................................................ 11

3.2 ELECTRICAL INSTALLATION .................................................................................................................................. 12

3.4 SETTING PARAMETERS ....................................................................................................................................... 15

4. MAINTENANCE AND SERVICE ..................................................................................................................... 16

5. FAILURES .................................................................................................................................................... 17

6. TECHNICAL SPECIFICATIONS ....................................................................................................................... 18

SEM BREAKTANK ART.NR.:2502925 ........................................................................................................................ 18

7.SPARE PARTS ............................................................................................................................................... 18

8. ASSEMBLE AND START USING OPTIONS ..................................................................................................... 19

BREAKTANK HA N D B O O K

06/2015 V4.0 2

For information

The Breaktank of SEM water treatment B.V.is a universal breaktank that is specially designed for the

supplementation (adding fresh water) of swimming pools. This break tank ensures the necessary

interruption between (drinking) water and swimming pool water. Under no circumstances can water

flow from the pool back into the water supply network, not even when the pressure on the grid

ceases. The SEM Breaktank meets the following standards:

EN1717

Backflow, siphoning and counter pressure are the greatest risks for the quality of drinking water. The

new European standard EN1717 is set up to prevent contaminated water entering the distribution

network of drinking water.

EN1377

A free outlet type "AB" provides a vertical and permanent interruption between the lowest point of

the feed opening and the critical level. The overflow must be non-circular and must be able to

discharge the maximum inlet flow rate under error conditions at positive pressure. Backflow of waste

water (sewage water) into the drinking water network is therefore also excluded

BREAKTANK HA N D B O O K

06/2015 V4.0 3

The SEM Breaktank can be used for the supplementation of a pool. By default, the SEM break tank is

equipped with a universal level control which can measure 1 level. A float switch is supplied to

measure the level in the skimmer or measuring tube. The lift pump has a capacity of 5 to 45 l / min at

11 to 28 m and is protected against dry running. The capacity of the break tank is about 0.8 m³ / hour

with the built-in mechanical float to fill the tank. Optionally, a solenoid valve is available which

increases the filling capacity to 1.5 m³ / hour.

The SEM Breaktank is supplied as standard with a mechanical float to fill the tank and the capacity

is 0.8m³ / hour. See attachment accessories and parts.

This manual contains all information to commission and maintain a SEM Breaktank.

Because the maximum make-up capacity depends on the connection size of the water pipe and the

required head, there may be differences between the capacities mentioned in this manual and the

capacity in your situation.

Warranty limitation

This documentation is provided by SEM Waterbehandeling B.V. She is in no way liable for damage,

direct or indirect, caused by the use of this documentation.

No guarantee is given for suitability for any special applications and parameter settings. SEM Water

treatment B.V. limited visibility to the replacement of parts or documentation to the extent that the

defects are not caused by improper use. For more information see our general delivery and payment

conditions. The guarantee period on this product is 1 year after the date of purchase.

Document rights

This documentation is the property of SEM Waterbehandeling B.V. located in Veldhoven. No part of

this manual may be reproduced or transferred by means of printing, photocopying, electronic

registration or in any manner whatsoever without the prior written permission of the publisher.

BREAKTANK HA N D B O O K

06/2015 V4.0 4

1. Introduction

The SEM Breaktank has been developed for refilling fresh water (supplementation) in a swimming

pool. The water level of the pool is measured with a level switch in eg the buffer, skimmer or level

pipe. If the level is too low, the pump will start and fresh water will be added. The construction of the

Breaktank is such that swimming pool water can never flow back into the pipeline network

(mandatory by the water company). The water supply network must never be operated by a closed

system connected to the pool. This must always be done by means of an open connection.

Specifications of the Breaktank:

• Complete interruption between pool and tap water according to European standard;

• Built-in level control for 1 pool.

• Switch-on delay 15 sec. and switch-off delay of 10 sec. for the level control. Both are adjustable.

This prevents oscillation of the delivery pump due to wave action in the pool.

• Clear display shows status (Run, Standby, Error);

• Simple menu structure (service and setup menu) with LED display and 3 push buttons;

• High Impact Polystyrene (HIPS) reservoir with a capacity of 15 liters;

• Level measurement of the reservoir by means of a pressure sensor. Level is readable in

millimeters in service menu.

• Mechanical float ½ "(approx. 0.8 m³ / hour) or solenoid valve ½" to fill the reservoir (approx. 1.5

m³ / hour).

• Low level protection to protect the feed pump against dry running.

• The self-priming feed pump (0.37kW) has a capacity of 5-45 l / min

 with a head from 10 to 28m (with a counter pressure of 1 bar approx. 2.5 m³ / hour). The pump

is equipped with a non-return valve and pressure gauge. Pump is switched with an electronic

relay,

 so no danger of sparking or sticking contacts.

• Print is equipped with a relay that switches on water demand. External systems can be

connected to this (max 3A / 230V).

• Glass fuse for electronics (250V / 160mA T) and for pump (250V / 3A T)

• Does not overflow circular, 40x140mm;

• Overflow connection ¾ "F;

• Empty connection with plug ½ ".

• Filling connection 1/2 "F PVC;

• Screw connection for all cabling with removable plugs.

• The Breaktank may only be used for cold water applications, maximum water

temperature 20 ° c.

BREAKTANK HA N D B O O K

06/2015 V4.0 5

2. Control

The Breaktank works completely automatically. Once in operation, the make-up can only be stopped

by shutting down the supply tap if necessary, or by switching off the supply voltage. Of course, the

float switch placed in the pool can also be "manually" influenced by placing it higher or lower relative

to the water level. This will shift the switching point and will eventually change the level of the bath.

The level control is equipped with a switch-on and switch-off delay so that the feed pump can never

"shuttle".

It is also important that the feed pump always runs with a back pressure of at least 1 bar. This is

necessary to let the pump run in its Q / H curve and does not suffer any damage due to overload or

cavitation. The pump pressure can be read on the mounted pressure gauge.

2.1 Display and buttons

The SEM Compact Breaktank is equipped with a digital display. The display shows all relevant

information.

Switch on the power supply:

After switching on the mains voltage, the break tank will show the software version on the display for

3 seconds. Changed settings will always be remembered after a power failure.

Normal operation:

The operating mode is shown on the display, followed by the speed of the pump in%.

StBy = Standby, break tank is standby

RUN= Pump of the break tank is in operation and replenishes the pool

RESET

LOAD

StBy

RUN

1.3

STATUS

BREAKTANK HA N D B O O K

06/2015 V4.0 6

Alarm notifications:

All alarm messages can be reset by pressing and at the same time, as soon as the fault

has been rectified.

Status light:

The status light is green when the pump is in operation. In the event of a fault, this light will flash red.

= green, pump in operation

= red flashing, fault, the fault code on the display indicates the nature of the fault.

ERR1= water level in the break tank is high, tank is running

ERR2= water level in the break tank is low, pump is blocked against running dry.

ERR3= settings in setup menu are incorrect. Adjust the values of HA, HB, HC, LA, Lb or

Lc.

ERR 1

300

ERR 2

ERR 3

BREAKTANK HA N D B O O K

06/2015 V4.0 7

2.2. Service menu

The service menu is opened by the button press for > 3 seconds. The decimal point on the

right of the display flashes to indicate that the service menu is active. The menu can be followed by a

short press on the button. The service menu is automatically closed after 10 seconds (except

in menu options L, i1 and i2)

Menuopti

Description

Explanation

Operating weeks

Number of weeks that the pump has been in operation

Operating hours

Number of hours the pump has been in operation.

Parameter ‘B’ and ‘U’ together gives the operating time

of the pump. (1 week = 168 hours)

Seri

al number

Serial number of the control board

ater

level

(Level)

The water level in the break tank is shown measured in

millimeters from the bottom of the tank.

In this mode, the setup menu is not automatically reset

after 10 seconds. so that the water level can be

followed while performing service work.

Input level switch 1

The input level of the input is displayed

0 = contact open (float up)

1 = contact closed (float down)

In this mode, the service menu is not automatically

reset after 10 seconds. so that the input signal can be

followed while performing service work.

Input level switch 2

The input level of the input is

displayed

0 = contact open (float up)

1 = contact closed (float down)

In this mode, the service menu is not automatically

reset after 10 seconds. so that the input signal can be

followed while performing service work.

Input 2 is for optional extensions and not used with the

standard versions

b. xxx

u. xxx

S. xxx

L. xxx

. x

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipos industriales de SEM

SEM

SEM SSD1-HS Manual de usuario

SEM

SEM 3000 Manual de usuario

SEM

SEM SSD2-HS Manual de usuario

SEM

SEM EMP-1000HS Manual

Manuales populares de Equipos industriales de otras marcas

ABB

ABB Unifix AD Manual

Mark 7

Mark 7 Evolution Manual de usuario

Husky

Husky HyPET Manual de usuario

bora

bora PM-1800 Manual de usuario

Grizzly

Grizzly T32428 Manual de usuario

Siemens

Siemens 8MF1 Series Manual de usuario

ABB

ABB HT610965 Manual de usuario

ABB

ABB SafeLink Manual de usuario

Phoenix

Phoenix PHX-150 Manual de usuario

ABB

ABB A165-L32 Manual de usuario

ABB

ABB HT842936 Manual de usuario

Rioned

Rioned UrbanJet Manual de usuario

Hermetica

Hermetica 10 Series Manual de usuario

HORNER

HORNER OEE Solution Manual de usuario

Hammerhead

Hammerhead HG375 Manual de usuario

SCHUNK

SCHUNK VERO-S NSE-A3 138 Instrucciones de uso

ABB

ABB HT566657 Manual de usuario

Webasto

Webasto GSE CAN Manual de usuario