Selkirk CF Sentinel Manual de usuario

SELKIRK CANADA CORPORATION

950 South Service Road, Second Floor

Stoney Creek, ON L8E 6A2

1-888-SELKIRK (735-5475)

Fax: 1-866-835-9624

www.selkirkcorp.ca

[email protected]

2021 CF Sentinel 3009214 02/12/21

(6” to 8” dia.)

FACTORY-BUILT

INSULATED CHIMNEY

Installer: It is of the utmost importance that these instructions are

left with the homeowner.

Homeowner: Keep these instructions and maintenance guide in a safe

place for future reference.

INSTALLATION I NSTRUCTIONS

MAINTENANCE G UIDE

Tested to Standard

CAN/ULC-S629

UL 103 Type HT

PLEASE READ ALL INSTRUCTIONS

BEFORE BEGINNING YOUR

INSTALLATION.

FAILURE TO INSTALL THIS SYSTEM IN

ACCORDANCE WITH THESE

INSTRUCTIONS WILL VOID THE

CONDITIONS OF CERTIFICATION AND

THE MANUFACTURER'S WARRANTY.

A MAJOR CAUSE OF

CHIMNEY RELATED FIRES IS

FAILURE TO MAINTAIN

REQUIRED CLEARANCES

(AIR SPACES) TO COMBUSTI-

BLE MATERIALS.

IT IS OF THE UTMOST

IMPORTANCE THAT THIS

CHIMNEY SYSTEM BE

INSTALLED ONLY IN

ACCORDANCE WITH THESE

INSTRUCTIONS.

Model CF

LISTED

6, 7

7, 8

8, 9

10, 11

12, 13

13, 14

15, 16

17, 18

CERTIFICATIONLABELS

TYPES OF APPLIANCES

PRE-INSTALLATIONGUIDELINES

TOOLS

CFSENTINELJOINTSECURITY

FRAMING DETAILS

CEILINGSUPPORTINSTALLATION

SMOKE PIPE ADAPTER

FIRESTOPJOISTSHIELD

ATTICINSULATIONSHIELDINSTALLATION

ELBOWINSTALLATION

WALLSUPPORTINSTALLATION

WALL BAND

CATHEDRALCEILINGSUPPORTINSTALLATION

ROOFSUPPORTINSTALLATION

ROOFFLASHINGINSTALLATION

ROOFBRACEKITINSTALLATION

ROUNDTOP

SPARK ARRESTER

MAINTENANCEANDCLEANINGOFCHIMNEY

REPLACEMENTPARTSLIST

ANCHORPLATEFORMASONRYFIREPLACE

CHART1-OFFSETCHIMNEYINSTALLATION

CHART2-CHIMNEYHEIGHTABOVEROOF

CHART 3 - CONNECTOR PIPE CLEARANCE

INSTALLATIONRECORD

TABLE OF CONTENTS

CERTIFICATIONLABELS

10pds.

2pds.

min.

3 pds.

min. 2 pds.

Authorities require that the chimney extend not less than 3 feet

(900mm)abovethehighestpointwhereitpassesthroughtheroof

of a building and not less than 2 feet (600 mm) above any portion

of the building within 10 feet (3 m). See figure 1 and Chart 2.

The ideal location for your chimney is within the building

envelope. In cold climates, the use of external chimneys may

result in operational problems such as poor draft, excessive

condensation of combustion products and rapid accumulation of

creosote. Under these circumstances, the installation of the

chimney within the building is strongly recommended.

If the chimney must be installed on an exterior wall it is

recommended that the chimney be enclosed below the roof line

to protect the chimney from cold outdoor temperatures, this may

helpreducecondensation,creosoteformationandenhancedraft.

Provide an access door by the Tee Plug for chimney inspection

andcleaning. Theexteriorenclosuremaybeinsulated,maintaining

the required minimum air space clearance of 2" (50mm) to any

part of the chimney. Consult local building codes for cold climate

applications.

Do not install the chimney directly at the outlet of the appliance.

Interconnecting smoke pipe is required unless the appliance is

specifically approved for that type of installation.

Use only with an appliance listed by a recognized testing

authority such as Underwriters Laboratories Inc., Underwriters

Laboratories of Canada, Intertek Testing Services, Warnock

Hersey or ICBO.

The flue diameter of gas or oil fired appliances should comply

with the appropriate Installation Codes such as CAN/CSA-B139

or CAN/CSA-B149 when installed in Canada, and the Installation

Codes NFPA 54, ANSI Z223.1 and NFPA 31 in the United States.

WARNING: DONOTPLACE ANY INSULATING MATERIALSOR RUN ANY ELECTRICAL

WIRINGWITHIN THE REQUIRED AIR CLEARANCE SPACESURROUNDING THE CHIMNEY.

MAINTAIN A2"MINIMUM AIR SPACE CLEARANCE BETWEEN

INSULATED CHIMNEYSECTIONSANDCOMBUSTIBLEMATERIALS.

YourCFSentinelchimneyandconnecting stovepipediametershould

be sized in accordance with the appliance manufacturer’s

recommendations.

Plan the installation of your appliance and chimney in such a way that

both your chimney and your chimney connector (stovepipe) run is as

short and straight as possible. By having too long and / or multiple

bend installations you can reduce system draft which can affect the

operation, and or performance of your appliance and or the chimney

system. Thechimney shouldbelocatedwithinthebuildingastoavoid

cutting or altering load bearing members such as joists, rafters, studs,

etc. Ifyouhavetocutoralteranexistingloadbearingmember,special

reframing methods are required which often include doubling of

adjacent members. If such a case arises, contact your local Building

Code Official regarding local regulations and proper installation

methods.

Before commencing the installation ensure that you obtain any

necessary building permits, and that your installation will conform with

all federal and municipal building codes requirement.

Sections of the CF Sentinel chimney which pass through accessible

areasof thebuildingsuch asthroughclosets,storageareas,occupied

spaces or any place where the surface of the chimney could be

contacted by persons or combustible materials must be enclosed in

a chase. The chase may be fabricated using standard building

materials. Drywall mounted on 2” x 4” studs is typically used in this

situation. Except for installation in single and two family dwelling,

factory-built chimneys shall be enclosed with approved walls having

a fire resistance rating equal or greater than that of the floor or roof

assemblies through which they pass. The space between the outer

wall of the chimney and the enclosure shall be at least 2 inches.

TYPES OF APPLIANCES

PRE-INSTALLATION GUIDELINES

If you have a basic knowledge of carpentry and how to use hand

tools, taking on the task of installing your new venting system will

beeasy. However,itisimportantthattheseinstallationinstructions

are followed. If you choose to have your product professionally

installed, we recommend these products be installed by

professionals who are certified in Canada by WETT (Wood

Energy Technology Transfer) or l'APC (l'association des

professionels du chauffage) or NFI in the US.

Be sure that ladders are in good condition and always rest on a

level firm surface.

Be sure that electrically powered tools are properly grounded.

YOUR CHIMNEY HAS BEEN TESTED, AND LISTED USING

ALL OF THE SUPPORTS, SHIELDS, ETC., DESCRIBED HEREIN.

DELETION OR MODIFICATION OF ANY OF THE REQUIRED PARTS OR

MATERIALS MAY SERIOUSLY IMPAIR THE SAFETY OF YOUR INSTALLATION,

AND VOID THE CERTIFICATION AND OR WARRANTY OF THIS CHIMNEY.

FIGURE 1

3 ft.

min.

CANADAAPPLICATIONS

Your CF Sentinel chimney has been tested per CAN/ULC-S629

as an all fuel chimney. As such it is code approved for connection

to solid, liquid or gas fueled residential type appliances and

building heating appliances in which the maximum continuous

flue gases temperatures do not exceed 650°C (1200°F). It has

also been tested and approved to withstand temperatures of up

to 2100°F for three thirty minutes intervals.

The installation should be in accordance with the Installation

Code CAN/CSA-B365 (Solid-Fuel-Burning Appliances and

Equipment) and / or the National Building Code of Canada and

Provincial Building Code, etc. should be consulted.

May also be used with specific factory-built fireplaces listed to

UL 127 and CAN/ULC-S610 when specified in the fireplace

manufacturer's installation instructions.

U.S.A. APPLICATIONS

The CF Sentinel chimney has been tested per UL-103 as "Type

HT". As such it is code approved for connection to solid, liquid

or gas fueled residential type appliances and building heating

appliances in which the maximum continuous flue gases

temperatures do not exceed 1000°F. It has also been tested and

approved to withstand temperatures of up to 2100°F for three ten

minutes intervals.

Theinstallationshould be in accordancewith NFPA211(Standard

for Chimneys, Fireplaces, Vents and Solid Fuel fired Appliances),

and / or local and regional codes such as the International

Mechanical Code and Uniform Mechanical Code, etc.

WEAR SAFETY GLOVES WHEN HANDLING

SHEET METAL PARTS WITH SHARP EDGES

CONTACT LOCAL BUILDINGOR FIREOFFICIALS ABOUT RESTRICTIONS AND

INSTALLATIONINSPECTION INYOURAREA.

6" 141/4" x 14/4"

362mm x 362mm

141/2" x 141/2"

369mm x 369mm 141/2" x 141/2"

369mm x 369mm

141/4" x 14/4"

362mm x 362mm

141/4" x 14/4"

362mm x 362mm 153/4" x 153/4"

400mm x 400mm 153/4" x 153/4"

400mm x 400mm

17" x 17"

432mm x 432mm 17" x 17"

432mm x 432mm

WebCoupler*

*Not exactly as shown.

Situate the chimney in the structure so that it can be installed

without cutting joists, sills, plates or load bearing partitions or

members.

Connect only one appliance to a chimney.

There should be no draft regulators on solid fuel equipment and

smoke pipe connector.

A minimum smoke pipe connector length of 3 feet (1 m) between

appliance and chimney is recommended.

Your CF Sentinel chimney system is designed for installation

using standard building materials and procedures. The following

tools may be required:

TOOLS

-safety gloves

-safety goggles

-hammer and nails

-tin snips

-tape measure

-screwdriver and pliers

-plumb line and level

-square

-keyhole saw or power jig saw

-caulking gun

Other tools or equipment may be required, depending on your

chimney location and the structure in which it is to be installed.

CF SENTINEL JOINT SECURITY:

High internal gas temperatures in a chimney force the internal

pipe to expand or lengthen. This, in turn, may cause the joints

to separate if they are not securely locked. The use of a chimney

cleaning brush may also cause the joints to separate if not

securely locked.

INSULATION COMPRESSION OF THE CF SENTINEL

Beforeassembling chimney lengths to one another, the insulation

on the female end (held in place with a plastic retainer) should be

below the outer bead so that it can compress during assembly.

The upper side (male end), should be full of insulation (held in

place with a white paper retainer and a web coupler) to the top of

the length. Once you have assembled the lengths together, a

locking band must be installed. With the insulation being

compressed, this will provide insulation to insulation contact (see

Figure 2).

NOTE: Whentheinsulation retainersmeltorvolatilize duringhigh

temperature operation, the compressed insulation will fill in.

FIGURE 2

Insulation

Locking Band

SeatedAll

Around

InsulationtoInsulation

Contact

InsulationCompressed

Outer Bead

SuspendedLength

Stainless Steel

SheetMetal

Screws FIGURE 4

Plan your installation carefully. If possible, position the stove so

that the flue outlet is centered between joists or rafters. Drop a

plumb line to the center of the flue outlet and mark this center

point on the ceiling. Lay out and frame in all openings ensuring

the specified 2” clearance to combustibles is maintained. Refer

to Table 1 or applicable Tables for framing dimensions and mark

the appropriate cutting lines around the center point.

FRAMINGDETAILS:

2. To remove the lockband, the clasp is pushed in and then

unhooked (see Figure 3B). Lift the clasp with a screwdriver if

necessary.

3. When a chimney section is suspended e.g: below a Cathedral

Ceiling Support, the band(s) and the joints must be fastened

using two (2) #6 x 1/2" stainless steel sheet metal screws (see

Figure 4).

FIGURE 3

INSTALLING THE LOCKING BAND:

NOTE: The chimney pipe and fittings must be assembled only

with the locking bands as furnished.

1. The clasp lockbands are simply seated in the beads of the

joints and clipped together (see Figure 2 & 3A). Typical Roof

Joist Framing

FIGURE 5

Typical Joist

Framing

2"Min.

FIGURE 6

TABLE1

*Note: The clearance to combustibles obtained with a correctly

installed Ceiling Support Assembly in the framed opening

specified above has been tested. The 2 inch clearance does

not apply at this location.

*Ceiling

Support Wall

(Support)

Thimble

FramingDimensions

All Other

Framing

Chimney

Flue

Diameter

Trim Plate

Ceiling

Support

Nailing Holes

3 Nails per Sides

(4 sides)

CEILING SUPPORT (CBSP)

- Suitable lengths of Chimney: - The chimney diameter should be

sized to suit the appliance.

- 15oor 30oChimney Elbow: - and suitable supports; resupport

assembly or roof support if required.

- Round Top: - To exclude rain and/or debris into the chim-

ney.

To complete a proper Ceiling Support installation, the following

parts will or may be required:

- Ceiling Support: - Required when supporting chimney with a flat

ceiling.

- Attic Insulation Shield: - Required where a chimney passes into

an unoccupied attic space.

- Firestop Joist Shield: - Required where a chimney passes from

a lower living space into an upper living space or occupied attic

space

- Roof Flashing Assembly: - Required where the chimney

penetrates a roof.

INSTALLATION PROCEDURES:

TheCFSentinel Ceiling Support will support up to 40feet(12.2m)

of chimney sections, all of which must be installed above the

support. Figures 10 & 11 illustrates the 2 most common types

of Ceiling Support Installation.

Frame (on all 4 sides) a level square opening with the inside

dimensions 14-1/4" (362 mm) square.

With the Lower Bucket removed, place the Ceiling Support

Assembly into the framed opening from below at the ceiling level

(see Figure 7).

The stub end (crimped) of the Smoke Pipe Adapter is intended

to fit inside of the connector pipe from a solid fuel appliance, thus

preventing condensate drips at the chimney connection.

Install inter-connecting stove pipe following appliance

manufactruer's instructions and appropriate building code re-

quirements keeping in mind that the stove pipe run should be as

short and straight as possible and secured in place with a

minimumof 3sheetmetalscrews per joint. Generally, for a wood

burning appliance installation, an 18" minimum clearance to

combustibles must be maintained for the stove pipe. NOTE: The

exception to this is a double wall stove pipe, such as Selkirk's

Model DSP which can be installed at reduced clearances to

combustibles. See separate installation instructions for more

details.

FIGURE8

SMOKE PIPE ADAPTER (SPA)

FIGURE 7

Basecap w/ Built-In

Smoke Pipe Adapter

Chimney

Length

Finish nailing through all the pre-punched holes (12 nails total)

and fasten the finishing plate onto the ceiling with the 4 supplied

black wood screws. Replace the Lower Bucket into the Ceiling

Support (see Figure 8).

Drive one nail, 1-1/2" common or spiral, part way into each of the

four (4) nailing areas of the support. Check that the trim plate is

level and flush (see Figure 7). You may substitute in lieu of nails

#8 x 1-1/2" wood screws.

Lower Bucket

Insert the Lower

Bucket into the

Ceiling Support

BEFORE LOWERING THE FIRST CHIMNEY LENGTH:

The Basecap Assembly with the short crimped Smoke Pipe

Adapter must be inserted into the female end of the first length

(see Figure 9a).

-Insertthe short portion of the short crimped Smoke PipeAdapter

into the Basecap.

- Ensure the Basecap portion is located on the inside of the

exterior casing of the insulated chimney (flush to the bottom of

the inward bead) and the Smoke Pipe portion is located over the

inner liner of the Chimney Length (see diagram 9b).

FIGURE9a

Installed Ceiling Support

All openings should be square (all four sides), plumb and in

perfect alignment with each other (see figure 5).

Forslopingroofsand/orceilings,ensurethattheframingdimension

is measured in the horizontal plane (see figure 6).

4-1/8"

2-1/2"

4-1/8"

FIGURE11

Floor, Ceiling Joist

(Framed all 4 sides)

Lower Bucket

FIGURE9c

TrimPlate

Smoke Pipe Adapter

Lower Bucket

CeilingSupport

Lower the prepared Chimney Length into the Lower Bucket.

Ensure that the Chimney Length rests on the Lower Bucket into

the Ceiling Support (see Figure 9c).

NOTE: Any length of CF Sentinel Chimney can be used.

There is no special "Starter" length required with the

Ceiling Support. Make sure the length is long enough to be

above the floor level or above the Attic Insulation Shield.

Continue adding chimney lengths until a height of about 2 feet

below the next ceiling level is achieved.

Chimney

Length

Inner Liner

of Chimney

Length

Insulation between

Outer Casing and Inner

Liner of Chimney

Length

Basecap Portion

(painted black)

Short crimped Smoke

Pipe Adapter Portion

Outer Casing of

Chimney Length

FIGURE9b

Inward bead of

outer casing

Beveled Portion Up

Crimpedend

Towards Appliance

FIRESTOP JOIST SHIELD (JS)

A Firestop Joist Shield (JS) must be installed where the

chimney passes from one living space to another living space as

shown in figure 11. It is designed to provide proper firestopping

between floors and to keep direct radiation from the chimney away

from the joist framing.

RoundTop

StormCollar RoofFlashing

Attic Insulation

Shield

FramedEnclosure2"(50mm)

clearance from chimney to

combustiblewall

ChimneySections

Living Space

Attic Space

Floor, Ceiling Joist

(Framed all 4 sides)

Floor, Ceiling Joist

(Framed all 4 sides)

Roof Joist

(Framed all 4 sides)

Two Story

Basement Installation

CeilingSupport

Living Space

FramedEnclosure2"

(50mm)clearancefrom

chimney to combustible

wall

Smoke Pipe Adapter

Firestop Joist Shield

FIGURE10

Firestop Joist

ShieldPositioned

intoFramingfrom

below

CloseBox Corners

UsingTabs

ChimneyLength

NailSideFlanges

Securely To Bottom

ofFraming

FIRESTOPPING

Firestopping is required at every joist level. Wherever a chimney

passes through a ceiling or floor, through a wall, or into an

enclosure, it must be firestopped. No firestopping is required in

conjunction with a Ceiling Support installed as shown in Figures

11, the Ceiling Support provides the firestopping.

A fire stop performs the following essential functions for both

dwelling and the chimney:

- Together with a fully framed opening (all four sides), it controls

vertical and horizontal spread of any fire external to the chimney.

- It stabilizes the chimney in the framed opening and defines and

maintains the required AIR SPACE clearance to combustibles.

- It reduces heat losses from the dwelling by blocking vertical air

circulation in the spae around the chimney.

- When located at a ceiling below a roof flashing (or below a roof

support) it helps provide stability for chimney extending above the

roof.

- At the level where the chimney penetrates the air/vapour bariier,

special attention is required. Seal the vapour barrier to the Ceiling

Support, Attic Shield (Joist Shield if the chimney is enclosed in the

attic) or Wall Thimble using an appropriate caulking compound as

per the requirement of local authorities.

14-1/4 x14-1/4

362 x 362 16-3/4 x16-3/4

426 x 426

15-1/2 x15-1/2

394 x 394

6" 7" 8"

The Attic Insulation Shield (AIS) provides 2 features: it comes

fully assembled with a built-in telescoping bottom shield,

eliminating the need for field assembly.The function of the Attic

InsulationShield(or a complete enclosure) is to keep insulation from

coming into contact with the chimney. Certain insulations made

of cellulose fiber (old newspapers, processed wood) may ignite

and smolder due to heat trapped by contact with the chimney.

When this smoldering fire reaches ordinary wood framing, a

flaming fire may resuilt. However, even without a flame, a

smoldering fire may create noxious gases and cause great

property damage.

An Attic Insulation Shield (AIS) must be installed where the chimney

enters an attic space. The Attic Insulation Shield is designed to

keep insulation materials from coming into contact with the chimney

and will protect up to a 10 inch 250mm) thickness of insulation plus

thedepth of the ceiling joists. If insulation is blown in and adheres

to the chimney pipe, it should be brushed off to eliminate any

possible contact of this material with the chimney when it is in

use.

The height of the AIS must accomodate the amount of insulation

as required by the National Building Code. Where height

restrictions will not permit the use of the Attic Insulation Shield, it is

permissible to construct an enclosure with the required minimum

air space clearance of 2" (50mm) to the chimney all the way to the

underside of the roof deck. In this application you will install a

Firestop Joist Shield (JS) at the ceiling level, with the exception of

a Single Story Installation (see Figure 13).

ATTIC INSULATION SHIELD (AIS)

Nail the AIS base to the framing dimensions with at least 2 per

side using 2d (1") spiral nails or 1" x #8 wood screws.

FramingDimensions

forAtticInsulationShield

DIAMETER

OFCHIMNEY

TABLE2

FRAMED

OPENING

Single Story

Installation

Attic Space

Roof Flashing

SmokePipeAdapter

RoundTop

StormCollar

ChimneySections

Attic Insulation Shield

CeilingSupport

Ceiling Joist

(Framed all 4 sides)

FIGURE13

Roof Joist

(Framed all 4 sides)

Lower Bucket

FIGURE 14 - Attic Insulation Shield

Fully frame a level square opening (all four sides) for 2" ( 50mm)

clearance from the outside of the chimney to the inside of the

frame. Place the Firestop Joist Shield (JS) up into the framed

opening from below the joist framing and nail in place using 1"

spiral nails as per Figure 10. Ensure no insulation or debris is

within the 2" air space clearance around the chimney. This

includes the air spaces between the Firestop Joist Shield (JS)

and the joist framing.

When the chimney is enclosed in the attic area, a Firestop Joist

Shield (JS) must be installed at the ceiling level. If the base of the

Firestop Joist Shield (JS) does not fit flush with the ceiling frame,

measure the distance that the base is sitting below the framing

and trim that amount off the top of the Firestop Joist Shield (JS)

before securing into place.

Attic Insulation

Shield(AIS)

Telescoping

Joist Shield

Nail Base to

Framing

Base (Fire Stop)

FIGURE12

Attic Insulation Shield

Intergrated Storm Collar

Telescoping Joist Shield Chimney Section

Attic space

For proper installation, the attic opening must be fully framed at

2 inches of clearance to the chimney pipe with framing material

of the same dimension as the ceiling joists (as per Framing

Dimension Table 2). The tabs on the base plate of the AIS are

inserted in the framed opening around the chimney. NOTE: This

only applies to the 6" AIS. On the 7" and 8" AIS, the tabs will

require to be flattened out and the AIS centered over the

framed opening.

When an Attic Insulation Shield is required above the Ceiling

Support into an attic as shown in Figure 13, ensure that the base

of the shield is flush with the top of the joist framing and nailed in

place. The telescoping portion of the AIS will eliminate the need

to trim the bottom when installed immediately above this support.

When fully exended, the AIS will also provide joist shielding when

installed in a 2 story main floor or basement applications (see

Figures 11 & 15).

SmokePipeAdapter

Elbow

ElbowSupportBand

Locking Bands

Elbow

Ceiling Joist

(Framed all 4 sides)

Floor, Ceiling Joist

(Framed all 4 sides)

RoundTop

StormCollar Roof Flashing

ChimneySections

Roof Joist

(Framed all 4 sides)

Elbow Support Straps

Locking Bands

CeilingSupport

Living Space

Attic Space Attic Insulation Shield

Offset(Elbow)Installation

FIGURE16

Lower Bucket

FramedEnclosure2"(50mm)

clearance from chimney to

combustiblewall

Install a Resupport Assembly on the vertical length just above the

highest elbow. Securely clamp the Support Band to the chimney

just above the locking band at the joint. Attach the Support Straps

to the Support Band assembly and nail the Support Straps to the

framingusing 1-1/2”nailsor#8x1-1/2"woodscrews (2perstraps).

See Figures 17 and 18.

The weight carrying capacity of the support, which depends on

the angle of the straps, and the security of attachment is

adequate for 9 m (30') of Model CF Chimney pipe.

ELBOW INSTALLATION

Framed Enclosure 2" (50mm)

clearance from chimney to

combustible wall

Living Space

Roof Flashing

CeilingSupport

Smoke Pipe Adapter

RoundTop

Storm Collar

Floor, Ceiling Joist

(Framed all 4 sides)

Ceiling Joist

(Framed all 4 sides)

Attic Insulation Shield

Attic Space

Chimney Sections

Two Story

Main Floor Installation

Roof Joist

(Framed all 4 sides)

Lower Bucket

NOTE:Toreducecoldairinfiltrationintothedwelling you can

installtheoptionalUniversalShieldingInsulation(SUSI)

into the Attic Insulation Shield. See separate installation

instructions.

FIGURE15

NOTE: At the level where the chimney penetrates the air / vapour

barrier,specialattentionisrequired. Sealthevapourbarriertothe

Ceiling Plate of the Ceiling Support, Wall Thimble or Attic

Insulation Shield using an appropriate caulking compound as per

the requirement of local authorities.

StainlessSteel

SheetMetal

Screws

FIGURE18

Two pairs (four) of 15oor 30oelbows may be used in an interior

installation to provide an offset in order to avoid cutting of joists and

to clear other obstructions.

Locking bands must be used at each joints. For added security

when forming an offset, it is required to fsten the joints using two

(2) X6 x 1/2" stainless steel sheet metal screws through the pro-

punched holes in the locking bands (see Figure 16).

The maximum permissible angle with solid fuel CF installation is 30

degrees. Combiningoffsetsforgreaterangleisnotpermitted. The

vertical run of chimney above an offset must be supported using an

Interior Resupport Assembly. Each Interior Resupport Assembly

will support 30 feet (9 m) of chimney and the maximum length of

chimney allowed between the elbows is 6 feet.

See Chart 1 for Offset Chimney Installation at the back of these

instructions for more information.

Never install an elbow in a joist area. Chimney sections must

pass vertically through a framed joist areas.

During installation provide supplementary support for the offset

section to avoid undue stress on connected elbows.

SupportBand

Straps

Locate Support

BandBelow

Locking Band at

Joint

Bend Straps

Over Framing,

Nail Securely

FIGURE17

11-1/2" (292mm)

12-3/4" (324mm)

14" (356mm)

14-1/2" (369mm)

15-3/4" (400mm)

17" (432mm)

10-5/8" (270mm)

11-7/8" (302mm)

13-1/8" (334mm)

WALL SUPPORT (WSP)

To complete a proper Wall Support installation, the following parts

may be required:

- Wall Support Package: - Intended for a through-the-wall installa-

tion where the chimney has a lateral connection.

- Adjustable Roof Flashing: - Required when the chimney

penetrates a roof or a roof overhang.

- Insulated Tee: - Required when the chimney is installed through

and along a vertical wall either on the exterior or interior.

- Wall Bands: - Required to provide lateral support to the chimney.

- Suitable lengths of chimney: - The chimney diameter should be

sized to suit the appliance.

- Interior Wall Plate and Exterior Wall Plate: - Required when going

through a combustible wall.

- Insulated Wall Thimble: - Required to satisfy through-the-wall

installation where framing an opening may not be practical.

- Round Top: - To exclude rain and/or leaves into the chimney.

The CF Sentinel Adjustable Wall Support will support up to 40 feet

(12.2 m) of chimney, all of which must be above the support.

1. Determine the center line of the lateral connection (horizontal

length through the wall) and frame in your opening to the dimen-

sions specified in Table 3. For a non-combustible wall (concrete

blockor pouredfoundation),cutahole 1/8"greaterthantheoutside

diameter of the chimney as per Table 3. DO NOT PLACE ANY

LOOSE INSULATION around the horizontal chimney length within

the framed opening when using a Wall Plate Spacer or Insulated

Wall Plate Spacer. Maintain the required minimum 2" (50mm) air

space clearance to combustible materials.

2. Assemble braces, brackets and angles to the base plate using 1/

4" nuts and bolts, with braces up or down as necessary (DOWN IF

CHIMNEY GOES THROUGH WALL) as per Figure 19 & 20a and if

it is an interior wall support installation (Figure 20b).

3. Nailbracketsand angles to framing temporarily making sure that

the base plate is level (and positioned to allow for the installation

of the wall plates, if the chimney goes through the wall).

TABLE3

Chimney

Size Hole

Non Combustible Framed Opening

Combustible Framing

For Bracing

Framingforthroughthewall

InsulatedTee

FramingforTeefacingaway

fromthewall

6. If the Tee is located on an outdoor wall, place the exterior wall

plate over the horizontal Tee branch, and attach an appropriate

insulated chimney length to the Tee branch. Secure in place with

the supplied locking band. Ensure that the clasp of the locking

band is facing down to prevent any water from collecting in the

lockingbandiflockingbandispositioned on the exterior of the wall.

NOTE: Interior or Exterior Plates can be substituted with the

Insulated Wall Thimble. In a combustible wall the opening must

be framed in (see Table 3).

Round Top

Storm Collar

Roof Flashing

Wall Plate Spacer

Wall Band

Locking Band

Exterior Wall

Plate (Louvered)

Insulated Tee

Angle Bracket

FIGURE19

4. Mark, and drill 5/32" pilot holes in the framing for the lag screw

location, or install masonry anchors in proper locations.

5. Remove nails, install lag screws or anchor bolts in all the holes

and tighten all bolts in the assembly.

FIGURE20A

ExteriorWallSupport Installation

Base Plate

Bolts

Angle Brace

Wall Bracket

Wall Angle secured to studs

with lag screws

Lag screws

Insulated Tee

Locking Band

Tee Plug with lugs

Exterior Wall Plate (louvered)

Maintain 2"

(50mm)

Min. clearance

Wall Plate Spacer

Locking

Band

9" Pipe Section

Min.

3" (76mm) Min.

39" (990mm) Max.

NOTE: THE CHIMNEY MUST EXTEND AT LEAST

3” (75 MM) INTO THE LIVING SPACE WHERE THE

SMOKE PIPE ADAPTER WILL BE ATTACHED TO THE

CHIMNEY BRANCH.

Locking Band

Smoke Pipe

Adapter

Tabla de contenidos

Otros manuales de Campana de ventilación de Selkirk

Selkirk

Selkirk UltimateOne Manual de usuario

Selkirk

Selkirk ULTRA-TEMP Instrucciones de uso

Selkirk

Selkirk SUPERVENT 2100 Instrucciones de uso

Manuales populares de Campana de ventilación de otras marcas

emmeti

emmeti RECUPA MED A-140 Guía

Nibe

Nibe F135 Manual de usuario

Kuppersberg

Kuppersberg INTRO 60 Instrucciones de instalación y mantenimiento

Zephyr

Zephyr Spruce AK9834BS Guía de instalación

Hisense

Hisense MH6INBG Manual de usuario

Miele

Miele DA 1255 Manual de usuario

Broan

Broan 46000 Manual de usuario

GE Profile PV977 Instrucciones originales

FALMEC

FALMEC FFRIA24W5FS Manual de usuario

Whirlpool

Whirlpool RH2600XL-1 SERIES Manual de usuario

Küppersbusch

Küppersbusch DX ISLA Manual de usuario

ETNA

ETNA AV360RVS Manual de usuario

JUNO

JUNO JDF603E6 Manual de usuario

Miele

Miele DA 6708 D Manual de usuario

Tricity Bendix

Tricity Bendix LE 150 Manual

AEG

AEG X68163BV1 Manual de usuario

AEG

AEG 125 D Manual de usuario

Smeg

Smeg KSEV97X Manual de usuario