Segway 1689500001 Guía de referencia

Customer Installable Parts

Upper Cargo Structure & Bag

e Series and i Series Models Only

Kit Number: 1689500001 Contents

·1 handlebar bag

·1 bag lid

·1 wire mounting frame

·1 control shaft clamp

·1 clamp screw

·2 button head screws

Specifications

·10 lb. maximum carrying capacity

·Polypropylene and polyethylene construction

·Polyester and mesh soft-sided pockets with cord locks

·Stainless steel snaps on bag lid

·Hook and loop attachment straps

·Powder-coated stainless steel wire mounting frame

Tools Required

·2.5mm hex wrench

·4mm hex wrench

WARNING

Always shut down your Segway HT and unplug the charge cord before performing any maintenance or installing any part or

accessory.

Follow these instructions carefully. Failure to follow these instructions carefully could damage your Segway HT and render it

unsafe to use.

Before you begin:

Do not use the parking stand to support the Segway HT while performing this procedure. The parking stand

is not designed to withstand the forces that may be generated. Instead, lay the Segway HT down on its back

side or support it with other objects so that you have easy access to the front of the handlebar and control

shaft.

Installation

Step 1

If present, remove the two button head

screws located on the bottom of the

handlebar using a 4mm hex wrench.

Step 2

Align the holes in the wire frame with the

screw locations in the bottom of the

handlebar so that the frame is on the front

side of the control shaft.

Step 3

Install the two button head screws through

the holes in the wire frame and into the

bottom of the handlebar using a 4mm hex

wrench and torque to 7.5 N-m.

Step 4

Install the clamp on the control shaft just

above the height adjustment collar with the

hook facing forward and up.

Note

Replace any fasteners you remove when performing this

installation with the new fasteners included in this kit .

Step 5

Slide the clamp up to the wire frame so that the wire frame rests in the hook.

Step 6

Install the clamp screw and with a 2.5mm hex wrench torque to 1.5 N-m. (The gap between the halves of the

clamp should be about 4mm.)

Step 7

Lightly tap the wire frame so that it snaps in the hook of the clamp.

Step 8

Drape the cargo bag over the handlebar so that the Display and Key Port are not obstructed.

Step 9

Secure the hook and loop straps around the wire frame at the bottom and sides of the bag.

LIMITED WARRANTY The Segway HT Upper Cargo Structure and Bag is an accessory covered by the SegwayTM

Human Transporter Limited Warranty (copy delivered with this kit).

Questions?

If you are missing a part, or if you need to return the product please contact Segway Customer

Service at 866.4SEGWAY (866.473.4929) or on our website at

www.segway.com/support/contact_us.html.

Tabla de contenidos

Otros manuales de Scooter de Segway

Segway

Segway Ninebot KickScooter Manual de usuario

Segway

Segway 12.0 Handlebar Bag Manual de usuario

Segway

Segway KickScooter Manual de usuario

Segway

Segway D18E Manual de usuario

Segway

Segway NINEBOT ONE S1 Manual de usuario

Segway

Segway RMP 210 V3 Manual de usuario

Segway

Segway MINILITE Manual de usuario

Segway

Segway E Series Manual de usuario

Segway

Segway i2 SE Manual de usuario

Segway

Segway i Series Manual de usuario

Segway

Segway Ninebot D18W Manual de usuario

Segway

Segway SE-3 Patroller Manual de usuario

Segway

Segway eMoped C80 Manual de usuario

Segway

Segway Ninebot KickScooter Manual de usuario

Segway

Segway i2 Patroller Guía de instalación

Segway

Segway Ninebot Gokart Pro Manual de usuario

Segway

Segway Ninebot Mecha Kit Manual de usuario

Segway

Segway Ninebot KickScooter F25I Manual de usuario

Segway

Segway i2 SE Manual de usuario

Segway

Segway i2 SE Manual de usuario

Segway

Segway E300SE Manual de usuario

Segway

Segway Ninebot KickScooter F2 E Manual de usuario

Segway

Segway x2 Turf Manual de funcionamiento

Segway

Segway Ninebot KickScooter F20A Manual de usuario

Manuales populares de Scooter de otras marcas

TEKTRO

TEKTRO CHEETAH Manual de usuario

Douglas

Douglas Vespa Sprint Guía de instalación

PLAYTIVE

PLAYTIVE AS-2448 Manual de usuario

Ebinger

Ebinger DONKEY XL Manual de usuario

Flyer

Flyer Mountain Guía del usuario

BackCountry eBikes

BackCountry eBikes Storm Manual de usuario

equipmed

equipmed FreeRoam II Manual de usuario

Yoto

Yoto Lion Manual de usuario

WESTHILL BIKES

WESTHILL BIKES LINK Manual de usuario

BAnff

BAnff eProdigy series Manual de usuario

Winther

Winther 475 Manual de usuario

Jetson

Jetson JBZL17 Manual de usuario

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Manual de usuario

Carrera

Carrera impel Manual de usuario

Afikim

Afikim Superlight SL-3 Manual de usuario

CareCo

CareCo ZOOM Manual de usuario

Douglas

Douglas Vespa G.S. Manual de usuario

Gazelle

Gazelle with BOSCH System Manual de usuario