Seeed studio Grove Manual de referencia

Grove - Loudness Sensor

Introduction

3.3V 5.0V Analog

The Grove - Loudness Sensor is designed to detect the loudness of environmental

sound. Based on amplifier LM2904 and a built-in microphone, it amplifies and filters

the high frequency signal that received from the microphone, and outputs a positive

envelop. This will make for Arduino’s signal acquisition. The output value depends on

the level of sound input. In order to avoid unnecessary signal disturbances, input

signal will go through two times’ filtering inside the module. Lastly, there is a screw

potentiometer that enables manual adjustments to the output gain.

Previous Version: v0.9b

Specifications

•Voltage ：3.5~10 VDC

•Working Frequency ：50~2000 Hz

•Sensitivity : -48~66 dB

•Signal-to-noise Ratio : >58 dB

•Output Signal range : Analog Signal (0-1023)

Tip

More details about Grove modules please refer to Grove System

Platforms Supported

Arduino Wio BeagleBone

Raspberry

LinkIt

ONE

Caution

The platforms mentioned above as supported is/are an indication of the module's hardware or theoritical compatibility. We only

provide software library or code examples for Arduino platform in most cases. It is not possible to provide software library /

demo code for all possible MCU platforms. Hence, users have to write their own software library.

Demonstration

With Arduino

This module uses the chip LM2904 to amplify the electronic signal produced by the

mini microphone. At last, you’ll get the analog-to-digital conversion value. Let’s try to

read the output value.

•As the picture on the below indicates, the Loudness sensor is connected to analog port

A0 of the Grove - Base Shield.

•Connect Arduino/Seeeduino to PC by using a USB cable.

•Copy and paste code below to a new Arduino sketch.

int val;

void setup()

{

Serial.begin(9600);

}

void loop()

{

analogRead(0);

delay(10);

val = analogRead(0);

Serial.println(val);

delay(200);

}

•Upload the code.

•Then open the serial monitor to observe the output results. There will be a significant

change when blow to the sensor.

The blue line is the original signal from microphone and the yellow is the sig pin of

Loudness Sensor. It is the original signal envelope that the module outputs. Here is

the test screenshot from the oscilloscope.

Blowing to the sensor:

Speaking to the sensor：

With Raspberry Pi

1.You should have a raspberry pi and a grovepi or grovepi+.

2.You should have completed configuring the development enviroment, otherwise

follow here.

3.Connection

•Plug the sensor to grovepi socket A0 by using a grove cable.

4.Navigate to the demos’ directory:

cd yourpath/GrovePi/Software/Python/

•To see the code

nano grove_loudness_sensor.py # "Ctrl+x" to exit #

import time

import grovepi

# Connect the Grove Loudness Sensor to analog port A0

# SIG,NC,VCC,GND

loudness_sensor = 0

while True:

try:

# Read the sound level

sensor_value = grovepi.analogRead(loudness_sensor)

print "sensor_value =", sensor_value

time.sleep(.5)

except IOError:

print "Error"

5.Run the demo.

sudo python grove_loudness_sensor.py

Otros manuales para Grove

Tabla de contenidos

Otros manuales de Accesorios de seeed studio

seeed studio

seeed studio Grove TA12-200 Manual de usuario

seeed studio

seeed studio Fall Detection Module Pro Manual de usuario

seeed studio

seeed studio Grove Fingerprint Sensor Manual de usuario

seeed studio

seeed studio Grove 101020049 Manual de usuario

seeed studio

seeed studio ReSpeaker Pro Case Manual de usuario

seeed studio

seeed studio RB-See-186 Manual de usuario

seeed studio

seeed studio Grove 101020033 Manual de usuario

seeed studio

seeed studio Grove - Temperature&Humidity Sensor Manual de usuario

seeed studio

seeed studio Grove Loudness Sensor Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

seeed studio Grove Manual de referencia

Manuales populares de Accesorios de otras marcas