Securitytec DVRMP4 Manual de usuario
1
Thank you for purchasing our product.
Please read this User’s Manual before
using the product. Change without Notice
4 Channel Digital Video Recorder
User’s Manual
2
CAUTION
RISK OF ELECTRICAL
SHOCK. DO NOT OPEN !
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER (OR BACK), NO USER
SERVICEABLE PARTS REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
Safety Precautions
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of insulated
dangerous Voltage within the product’s enclosure that may be
sufficient magnitude to constitute risk of electrical shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operation and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE UNITS NOT SPECIFICALLY DESIGNED FOR
Attention: installation should be performed by qualified service
Personnel only in accordance with the National Electrical Code or
applicable local codes.
Power Disconnect. Units with or without ON-OFF switches have power
supplied to the unit whenever the power cord is inserted into the power
source; however, the unit is operational only when the ON-OFF switch
is the ON position. The power cord is the main power disconnect for all
unites.
There are no serviceable parts for this unit, call for your agent for
details.
Warranty
and Service
3
Before installing stand alone DVR, be sure to thoroughly review and follow the instructions in this Users
Manual. Pay particular attention to the parts that are marked NOTICE.
Also, when connecting with external application, first turn the power OFF and follow manual
instruction for appropriate installation.
1. This document is intended for both the administrator and users of stand alone DVR Model.
2. This manual contains information for configuring, managing and using stand alone DVR Model.
3. To prevent fire or electrical shock, do not expose the product to heat or moisture
4. Be sure to read this manual before using stand alone DVR Model.
5. For questions and technical assistance of this product, contact your local dealer.
►Strong recommendation on installation of the DVR unit
1. Check electricity at the place you want to install the DVR unit is stable and meets our electricity
requirements.
Unstable electricity will cause malfunction of the unit or give critical damage to the unit.
2. Several chips on the main board of the DVR unit and hard disk drive inside the unit generate heat, and it
must be properly discharged.
Do not put any objects just beside exhaust port(fan) on the left side of the unit and do not close up an
opening (fresh air in-take) on the right side of the unit..
3. Put the DVR unit at well-ventilated place and do not put heat-generating objects on the unit.
When it is installed inside 19 inch mounting rack together with other devices, please check built-in
ventilation fan of the rack is properly running.
About this document
Before reading this document
4
FCC Statement:
WARNING
This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference. (2) This device must accept any interference received
including interference that may cause undesired operation."
* Federal Communications Commission (FCC) Statement
WARNING
This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
* You are cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void your
authority to operate the equipment.
5
Safety Precautions………………………………………………….……………………. 2
Content Table……….…………………………………………………………………….. 4
1. Hardware…………………………………………………………………………………… 4
2. Unit Description of Front Panel………………………………………………………….. 5
3. Unit Description of Rear Panel…………………………………………………………… 6
4. Installation……………………..…………………………………………………………… 7
1. Procedure……..……………………………………………………………….… 7
2. Picture…………………………………………………………………………… 9
3. Playback………..………..……………………………………………………… 11
5. Function Setup…………………………………………………………….………………… 13
1. Log-in………..………………….……………………………………………….. 13
2. Basic Operation………………………………………………………………… 14
6. Specifications…………..………………………………………………………………….… 36
7. PTZ Control…………………………..……………………………………………….. …… 38
1 X DVR Machine
1 X Power Cord
1 X IDE cable
1 X Adaptor 12V
1 X User Manual
1 X Remote controller
1X CD
8 X Screw (Without Hard Disk)
4 X Screw (Within one Hard Disk)
Content Table
Hardware
6
1 ~ 4 camera channel full screen choose button / 0 ~ 9 password input
Unit Description of Front Panel
Picture 2x2 zoom in
Picture Freeze
Quad screen display button
Channel auto sequence button
Picture in picture button
Function menu button
Time search button
Key lock button
Function exit button
Value change button
Direction button Up and Down /
Record or playback stop /
playback pause or step button.
Direction button left and right,
Fast / Slow Reverse,
Fast / Slow forward playback.
JOG Shuttle USB port
Remote controller IR
PIP
ZOOM
FREEZE
POP Picture on picture button
AUTO
MENU
ESC
LOCK
BACKUP Image backup button
T-SRH
PLAY Image playback button
REC Image record button
7
NOTICE:
VGA connection is not a standard video output of this unit. Call your local dealer for optional purchase.
Unit Description of Rear Panel
Power cord in DC 12V, power switcher
Camera 1 ~ 4 input and
looping output
Audio channel input x 4 and
output x 2
75 ohm high and low dips switch / Monitor out
Network connector.
VGA
RS 485 A + / B –
Alarm In: 1 / 2 / 3 / 4
Relay: NO / NC / COM
8
1) Camera Connection
Connect camera to the CAMERA INPUT
located at rear side of the DVR.
2) Monitor Connection (Composite Connection
Method)
Connect monitor to the MONITOR output
located at rear side of the DVR.
3) Sensor Connection
Connect the Sensor to the SENSOR INPUT / OUTPUT at the Rear Panel of the DVR
Relay output : COM+NC, COM+NO
Alarm input : Short-circuit between Alarm1, Alarm2, Alarm3 or Alarm4 and GND is recognized as alarm.
Alarm 1~4 = Camera1~4.
NOTICE: Sensor input is recognized as LOW when alarm signal is on a level with GND, and it is recognized as
HIGH when alarm signal is FLOATING or 5V. Following is internal circuit.
Thus, there is a danger of damage, when the sensor input goes to a Negative level or voltage higher than 5V.
Installation
Internal Circuit D1
5
V
Procedure
9
4) HDD internal connection
Masterx1 Masterx1/Slavex1
Master x 1 / Slave x 1 CD-RW Master x 1 / Slave x 1
Master x 1 / Master x 1 CD-RW Master x 1 / Master x 1
Slavex1/ Slavex1 Slavex1/ Slavex1
Notice:
-Hard Disk Master and Slave jumper pin must be right, otherwise DVR will show fault.
10
5) Power Connection
Connect the power to the POWER
CONNECTION on the Rear Panel of the
system, and turn on the switch.
6) Turn on the POWER.
Make sure the adaptor is 12V
7) Detail setup in SYSTEM SETUP
For detail setup, refer to the instruction of SYSTEM SETUP.
Full screen or quad screen display
Press button to display quad screen.
Press numeric 1 / 2 / 3 / 4 buttons to display the desired camera image in full screen.
1.) FREEZE Mode
1. In live and the quad mode press (FREEZE) button to freeze image.
Press again to cancel freeze mode.
2. On the full screen display, press (FREEZE) button to
freeze full screen image.
2.) Zoom Mode 2 x 2 (Display Enlargement.)
Press numeric button to enter full screen mode, then press ZOOM button to enlarge screen.
Use button to move position.
3.) Auto Mode
Press (AUTO) button to enable channel auto sequencing.
Picture
Tabla de contenidos
Otros manuales de DVR de Securitytec
