Security-Center TV7202 Manual de usuario

Security-Videoserver

Installation instructions

TV7202

Preface

Dear Customer,

Thank you for purchasing this video server of the DIGILAN series from Security Center. You made the right decision

in choosing this state-of-the-art technology,

which complies with the current standards of domestic and European regulations. The CE has been proven and all

related certifications are available from the manufacturer upon request.

To maintain this status and to guarantee safe operation, it is your obligation to observe these operating instructions!

In the event of questions, please contact your local specialist dealer.

This video server is used for object surveillance. The recorded video signals are transmitted to a computer digitally

via the connected network. The computer software permits simultaneous recording of up to 16 connected video

signals. Data storage is subject to local national data-protection guidelines. Via the Internet Explorer, you have

worldwide access to installed cameras (password-protected).

Precautions

The video server and connected components must be kept free of moisture (cellars and similar surroundings are to

be strictly avoided). Use of this product for other than the described purpose may lead to damage of the product.

Other hazards such as short-circuiting, fire, electric shock, etc., are also possible. The equipment is designed for

operation using a Class 2 12V DC transformer. No part of the product may be changed or modified in any way.

Connection to the public power network is subject to country-specific regulations. Please be aware of applicable

regulations in advance.

To avoid fire and injury, please observe the

following:

Securely fasten the device at a dry location in the

building.

Ensure sufficient air circulation.

Do not expose the device to temperatures less than

0°C or more than 50°C.

The device is designed for indoor use only.

Humidity must not exceed 90% (non-condensed).

Ensure that the voltage is disconnected when

performing work on the device.

Please observe the following regulations to ensure

trouble-free operation of your device.

The security video server is supplied by a 12V DC

transformer. The transformer should be connected

to the 230V AC building mains by means of a

separate, electrically protected line.

Connection work to the building mains is subject

to country-specific regulations.

General:

Improper or careless installation work may lead to faults and poor image quality. Therefore please read the

instructions very carefully and follow the installation instructions for lines and components precisely.

Before using this product

The use of surveillance equipment may be forbidden by law in some countries. This security network camera is not

only high-quality web camera but can also be used as part of a flexible surveillance system. Before using this

equipment, make sure that all your surveillance activities are completely legal.

Before installation, check the product for completeness (page 5: Scope of delivery). Read the installation instructions

before installing the video server. Read the “Installation” chapter carefully and follow the instructions contained in it

to avoid damage caused by faulty assembly or incorrect installation. This will ensure that the equipment goes into

operation correctly for the intended purpose.

Appendixes A and B contain possible solutions to problems occurring during installation and configuration. Refer to

this chapter first if you have problems configuring the system. The installation instructions describe different usage

scenarios of the video server.

Sections marked with contain special hints and advice for the user. Ignoring this advice can result

in damage to the equipment or injury to the user.

Contents

Preface……………………………………………………………………………………………………….….……. 2

Precautions…………………………………………………………………………………………………….……… 2

Before using this product…………………………………………………………………………………………….. 3

Contents………………………………………………………………………………………………………….…… 4

Scope of delivery…………………………………………………………………………………………………..…. 5

Hardware installation……………………………………………………………………………………………….... 6

First access to video server…………………………………………………………………………………………..10

Setting the IP address……………………………………………………………………………….…10

Access to the video server via the Internet Explorer………………………………….……………….13

Installing the plug-in………………………………………………………………………….………..13

Primary user privileges…………………………………………………………….….......................13

Client settings…………..……………………………………………………….……………….…… 15

System configuration…………………………………………………………………………………..………….… 16

System………………………….…………...………………………………………………………… 16

Security……………………………………………………………………………………………...… 17

Network…………….……………………………………………………………………….……...…. 19

SMTP…………………………………………………………………………………………….19

FTP…………………………………………………………………………….…………...….. 20

UPnP and DDNS settings……………….………………….……………………………………...…. 22

Video……………………. ……………………………………………….…………………………...23

Motion sensor…………..…………………………………………………………………................ 25

Camera control…………………………………………………………………………………..……26

Modem……………………………………….……………………………….………………………. 30

Application……………...…………………………………………………………………………..…31

Homepage layout…………………………….………………………………..…………………….. 33

Viewing the log file …….…………………………………………………………………………..… 33

Viewing parameters…………………………………………………………………………….….…. 33

Factory settings……………………………………………………………………….….…….…..…. 34

Deleting the data path for owner commands………………………………………………….……. 34

FTP…………………………………………………………………………………………………….. 34

Viewing the system log……………………………………………………………………………….. 34

Uploading the configuration file…………………………………………………..………...………. 35

Updating the software version……………………………………………………………………….. 35

Telnet………………………………………………………………………………………..………… 36

Modem environment……………………………………………………………………………………………….. 38

Hardware installation………………………………………………………………………………... 38

Software installation………………………………………………………………………................ 39

Access to video server…………………………...………………………………………….……….. 47

URL commands of the video server………………………………….…………………………………………..… 49

Appendix………………………………………………………………………….………………………..……….. 56

A. Post procedure……………………………………..........………….……………………………..… 56

B. Frequently asked questions (FAQ)……………….……………………..………………………….… 56

C. Technical data…………………………………………………………………..…………..………… 58

Scope of delivery

Video Server TV7202

Transformer

Software CD

Installation instructions (on CD)

Hardware installation

Make sure that all accessories and articles listed above are present in the scope of delivery. Depending on

application, an Ethernet cable may be required. This Ethernet cable must meet the specifications of UTP Category 5

(CAT 5) and must not be longer than 100 meters.

Front

BNC video input

The video port with 75-Ohm resistor is used for connecting an analogue camera. To ensure that the video

modulation mode is correctly detected, the camera must be connected and switched on before the video server is

switched on.

RCA audio input

The audio input is connected via the RCA port of the Mono-Audio-Line-In signal.

Rear

To prevent the risk of electric shock, first connect the

socket of the transformer to the video server before

inserting the transformer into the mains socket.

Ethernet 10/100 socket

Use a UTP category 5 (CAT 5) cable not longer than 100 meters to connect to the Ethernet. When the Ethernet

cable is correctly connected, the video server uses the Ethernet interface, regardless of any modem connection.

COM port

If no Ethernet is available, connect a modem cable or the null modem cable supplied to this serial RS232 port

(COM port) to be able to use the communication network. If an Ethernet connection is available, the administrator

can use this port for controlling a PTZ camera connected to the video port.

I/O terminal block

1 ÅDI+ Input (max. 50mA, 12V DC)

2 ÅDI- Input

3 ÅSW_COMMON Output (NOC, normally open contact: switch closes on event)

4 ÅSW_NOPEN Output (max. 1A, 24V DC)

5 ÅRS485 - (RS485 interface)

6 ÅRS485 +

The video server has a very flexible, general I/O interface to make it compatible with the user’s security equipment

such as sensors, alarm systems, lighting or door locks. The general I/O terminal block has 6 pins for device control.

These are divided into two categories according to their functions.

If the device connected to COM has an RS485 interface, connect two control lines to pin 5 and pin 6. After you

switch to RS485 on the configuration page, PTZ control commands are routed via pin 5 and pin 6. If the distance

to the controlled device is too great to ensure precise functioning, use an external voltage supply to amplify the

RS485 signal.

The video server has a digital input and a relay switch for device control. If you connect pin 1 and Pin 2 to an

external sensor, the status of the operating voltage is monitored according to the programmed script in the

configuration. You can switch the external device on and off with the relay switch.

LED status display

Every time you start the video server, it runs a self-test. The self-test checks all hardware modules. When the

administrator connects the transformer both LEDs (LED 2 & 3) under the network LED flash until the self-test is run. If

any of the modules is faulty, both LEDs flash according to the pattern described in Appendix A. If the self-test is

passed, both LEDs switch off for a short time and then light according to the pattern described below. The network

interface depends on the Ethernet, modem or null modem cable peripherals. If the Ethernet connection between the

video server and the Ethernet is functioning, the video server chooses the Ethernet. If the Ethernet is not available

but a functioning modem is connected, a connection is established via the modem. If neither the Ethernet nor the

modem is available, the video server attempts to connect via the null modem.

Network interface Condition LED2 LED3

Before installation OFF OFF

After installation Flashing OFF

Ethernet

Camera control Flashing Flashing

PPP with modem After self-test Flashing ON

Before connection ON ONPPP with null modem

After connection Flashing ON

Resetting system settings

In the opening next to the I/O terminal block is a button. Press this button to reset the system or restore the factory

parameter settings. If the system cannot be not installed or is not working normally, use the pointer supplied and

follow these instructions for restoring the initial (factory) status of the system.

Insert the pointer in the hole and press the reset switch. Keeping the switch pressed, restart the system by

disconnecting and reconnecting the transformer. The system runs the self-test twice instead of the usual once, which

you can see by the flashing LEDs. After the second flashes of the LEDs, remove the pointer to release the reset

switch. The factory-set parameters are now restored.

Transformer

Connect the transformer to the voltage in socket of the video server (12V DC).

Switching on

Before installing further video servers, make a note of the serial numbers for future reference.

Before connecting up, all peripheral devices must be switched off. Use the cable supplied to connect the video

server to the peripherals as described below.

Important: Do not switch on the transformer until all other cables have been properly connected.

Make sure that all cables are correctly connected before switching on the video server. Switch on the cameras,

sensors and alarm device and then plug the transformer of the video server into the mains wall socket. If the self-test

is successful, the network speed and the video modulation mode are automatically detected. When the addressing

procedure is complete, the video server is ready to use. If the video modulation mode could not be detected, the

administrator can change the setting on the configuration page. For further information, see the section “System

configuration”.

First access to video server

Setting the IP address

To set the IP address of the camera:

Use a network cable to connect the video server to your computer network.

(The simplest way is to connect the video server direct to your PC using a cross-link cable.)

If your PC is not yet integrated into a network, you first have to configure it for the network application. Do this by

opening the Properties page for your network.

(This also applies if the camera is connected to the PC via a hub or switch.)

1. Click , select and open the Properties page of the

2. Enter a fixed IP address and subnet mask

(e.g., 192.168.0.95 and as subnet mask 255.255.255.0).

- The network connection of your PC is now configured.

Tabla de contenidos

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario