SecureALL SA-MDR Manual de usuario
SecureALL Corporation
SA-MDR Installation Guide
Version 3.0
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 2 of 22
All Rights Reserved
SecureALL Corporation
SA-MDR Installation Guide
Copyright © 2012 by SecureALL Corporation.
All rights reserved under International and Pan-American copyright conventions. No part of this
document may be reproduced in any form or any means, electronic or mechanical, including
photocopying, without permission in writing from the Company. All inquiries should be
addressed to SecureALL Corporation, 695 Woburn Court, Mountain View, CA 94040.
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 3 of 22
All Rights Reserved
Revision History
Version
Date
Author
Revision Description
1.0
02-15-2012
JDS
Initial version
2.0
08-15-2012
RAS
Added step for changing lock from RH to LH;
added instructions for installing the flex cable
that has replaced the 14-pin cable; added step to
check current level post battery installation; new
mortise cutout template.
3.0
7-16-2013
RAS/DAC
Added spacer and corrected bill of materials
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 4 of 22
All Rights Reserved
Table of Contents
Revision(History(.............................................................................................................................(3(
Table(of(Contents(...........................................................................................................................(4(
Introduction(.....................................................................................................................................(5(
Configuring(the(Mortise(Chassis(..............................................................................................(6(
Installation(Instructions(.............................................................................................................(7(
Appendix(A(-(Mortise(Cutout(Template(...................................................................(16(
Appendix(B(-(Mortise(Lock(Assembly,(Exploded(View(.........................................(18(
Appendix(C(-(Screw(Package(.......................................................................................(19
(
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 5 of 22
All Rights Reserved
I. Introduction
These instructions are to be used to install a SecureALL SA-MDR mortise door reader. This
document assumes availability of a door with a cutout pocket for an industry standard, ANSI
Grade 1, heavy-duty mortise lock. See Appendix A for cutout dimensions.
Required Tools:
1. Phillips head screwdriver (Size #3 Drive)
2. Phillips head screwdriver (Size #2 Drive; pitch: 0.6) for Escutcheon Cover Screws
3. Allen wrench - supplied by SecureALL
Check the Materials:
Verify that the following materials are included and there is no visible damage. If there are any
damaged or missing items, contact SecureALL immediately for assistance. See Appendix B for
an exploded view of the lock and Appendix C for pictures of the screw hardware.
ITEM NO. PART NO. DESCRIPTION QTY
1 190-000176 FACE PLATE 1
2 850-000122 MORTISE CHASSIS ASSEMBLY 1
3 190-000177 INSIDE LEVER ASSEMBLY 1
4 190-000178 OUTSIDE LEVER ASSEMBLY 1
5 190-000171 SPINDLE W/SCREW (SET) 1
6 190-000189 SPACERS, 1/4" HIGH 2
7 190-000172 MOUNTING POST 2
8 190-000173 TRIM SCREW 2
9 820-000127 INSIDE COVER ASSEMBLY 1
10 820-000128 OUTSIDE COVER ASSEMBLY 1
11 820-000129 INSIDE RF ASSEMBLY 1
12 190-000175 DUST BOX 1
13 190-000179 STRIKE PLATE 1
14 190-000168 MORTISE SCREW 2
15 190-000166 CHASSIS SCREW 2
16 190-000170 SCALP SCREW 2
17 190-000167 ESCUTCHEON COVER SCREW 3
18 190-000169 STRIKE SCREW - FINISHED 2
19 530-000100 AA BATTERIES 3
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 6 of 22
All Rights Reserved
II. Setting the mortise chassis
The diagram below gives the instructions to change from an inside (i.e. door opens in) to an
outside (i.e. door opens out) lock unit or from an outside to an inside lock unit. Picture #1 shows
an outside opening right hand door and #4 shows an inside opening right hand door.
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 7 of 22
All Rights Reserved
If it is necessary to change from a left hand inside opening lock unit to a right hand inside
opening lock unit (or vice versa), first follow the procedure above to reverse the latch bolt. The
locking side must then be reversed. Unscrew the two screws in the left figure below and put
them in the same screw holes on the other side of the chassis.
III. Installation Instructions for Left Hand, Inside Opening Door
1. Orienting the Chassis Assembly (Item 2) as shown in Figure 1a, carefully thread the two
cables into the door pocket and through the second hole as shown in Figure 1b. Holding
the cables taut, push the Chassis Assembly all the way into the pocket.
Figure 1a Figure 1b
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 8 of 22
All Rights Reserved
2. Using Mortise Screws (Item 14), secure the Chassis Assembly to the door, as shown in
Figure 2.
Figure 2
3. Place the outside Spindle (Item 5A) and inside Spindle with Screw (Item 5B) in the
Chassis Assembly and tighten the screw that is embedded inside Item 5B with the
Phillips screwdriver. See Figures 3a & 3b.
Figure 3a Figure 3b
Item 14
Item 5B
Item 5A
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 9 of 22
All Rights Reserved
4. Mount Outside Lever Assembly (Item 4) on the outside Spindle. Insert Mounting Posts
(Item 7) through the holes in the Outside Lever Assembly, making sure they are
completely inserted. See Figure 4.
Figure 4
5. Mount the Outside Cover Assembly
a. Hold the Outside Cover Assembly (Item 10) perpendicular to the door as shown
in Figure 5a.
Figure 5a
Item 7
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 10 of 22
All Rights Reserved
b. Slide the Outside Cover Assembly toward the handle until it butts up against the
handle end (Figure 5b).
Figure 5b
c. Rotate the Outside Cover Assembly clockwise and then push it toward the handle
until the end is within the Outside Cover Assembly cutout (Figure 5c).
Figure 5c
Tabla de contenidos
Otros manuales de Cerrar de SecureALL
