Remote control LT5
Intruder alarm system Installation manual
STATUS INQUIRY
ALARM CLEARING WITH BUTTON (SINGLE PRESS OPERATION)
TRIGGERING PANIC ALARM WITH BUTTON. COMMAND SENDING WITH PRESSING THE BUTTON
BATTERY REPLACEMENT
The answer from the system depends on system status (see picture).
Press the button.
GR
Red (short) = PGM output is turned Off
Red (long) = command is executed /PGM output is turned
No flash = No answer from the system!
B
R
R
If the command is executed / PGM output is turned On the answer from the system will be long Red color
flash. If the PGM output is turned Off the answer from the system will be short Red color flash.
Green(short:~0,1sec)=batteryisgood
Red(short)=batteryislow
Answer from the
system
G?
G
R
Command sending and
battery status indication
Green (short: ~0,1 sec) = system is disarmed
Red (long: ~1 sec) = system is armed in Away mode
Blue (long) = system is armed in Night mode
Green (long) = system is armed in Stay mode
White (long) = system is armed in Max Away mode
No flash = No answer from the system!
B
R
G
W
G
Press the button while the
Red color light is visible on LED
and wait answer from the system.
Only one command is assigned to
button in default project. This is the
reason why only Red color light will be
visible on LED.
If the panic alarm is succesfully triggered the answer from the system
will be long Red color flash on LED.
RRed (long) = panic alarm is
triggered
No flash = no answer from the
system!
Answer from the
system
GRR
Red =Panic
Green = Not Used
Blue = Not Used
White = Not Used
RB
G
WR
B
GW
Pleaseactaccordingtolocallaws.Don'tthrowawayunusablealarmsystemsorit'scomponentsalongwithhouseholdwaste.
ThisproductsutilizationinEUstatesisregualtedbyEUdirective2002/96/EC
Batteryintheremotecontrolunitlifetimedependingontheenvironment,usageandthespecificwirelessdevicebeingused.Factorssuchashumidity,high
or low temperatures, as well as large swings in temperature may all reduce the actual battery life.When the battery is nearly dead, the remote control unit
showsthatwiththeLED.ItisshowingthebatterystatusonLEDwhenitissendingacommandtoreceiver.
BATTERY REPLACEMENT
Insert the blade of a small
screwdriver between the remote
control unit plastic top and bottom
cover and slightly turn it.
Remove the screw that is holding
the electronic circuit board in place. Insert the blade of a small
screwdriver in place as it is shown in
picture and carefully remove the
electronic circuit board from plastic
housing.
Use an isolated stick and remove the old battery.
With a positive (+) end of a new battery facing UP,
insert the new battery as shown in picture.
New battery
2
1
Remote control LT5
Intruder alarm system Installation manual
STATUS INQUIRY
ALARM CLEARING WITH BUTTON (SINGLE PRESS OPERATION)
TRIGGERING PANIC ALARM WITH BUTTON. COMMAND SENDING WITH PRESSING THE BUTTON
BATTERY REPLACEMENT
The answer from the system depends on system status (see picture).
Press the button.
GR
Red (short) = PGM output is turned Off
Red (long) = command is executed /PGM output is turned
No flash = No answer from the system!
B
R
R
If the command is executed / PGM output is turned On the answer from the system will be long Red color
flash. If the PGM output is turned Off the answer from the system will be short Red color flash.
Green(short:~0,1sec)=batteryisgood
Red(short)=batteryislow
Answer from the
system
G?
G
R
Command sending and
battery status indication
Green (short: ~0,1 sec) = system is disarmed
Red (long: ~1 sec) = system is armed in Away mode
Blue (long) = system is armed in Night mode
Green (long) = system is armed in Stay mode
White (long) = system is armed in Max Away mode
No flash = No answer from the system!
B
R
G
W
G
Press the button while the
Red color light is visible on LED
and wait answer from the system.
Only one command is assigned to
button in default project. This is the
reason why only Red color light will be
visible on LED.
If the panic alarm is succesfully triggered the answer from the system
will be long Red color flash on LED.
RRed (long) = panic alarm is
triggered
No flash = no answer from the
system!
Answer from the
system
GRR
Red =Panic
Green = Not Used
Blue = Not Used
White = Not Used
RB
G
WR
B
GW
Pleaseactaccordingtolocallaws.Don'tthrowawayunusablealarmsystemsorit'scomponentsalongwithhouseholdwaste.
ThisproductsutilizationinEUstatesisregualtedbyEUdirective2002/96/EC
Batteryintheremotecontrolunitlifetimedependingontheenvironment,usageandthespecificwirelessdevicebeingused.Factorssuchashumidity,high
or low temperatures, as well as large swings in temperature may all reduce the actual battery life.When the battery is nearly dead, the remote control unit
showsthatwiththeLED.ItisshowingthebatterystatusonLEDwhenitissendingacommandtoreceiver.
BATTERY REPLACEMENT
Insert the blade of a small
screwdriver between the remote
control unit plastic top and bottom
cover and slightly turn it.
Remove the screw that is holding
the electronic circuit board in place. Insert the blade of a small
screwdriver in place as it is shown in
picture and carefully remove the
electronic circuit board from plastic
housing.
Use an isolated stick and remove the old battery.
With a positive (+) end of a new battery facing UP,
insert the new battery as shown in picture.
New battery
2
1
Old battery
Press the button.
Page 3
Rev.01/02/16
