SECO-LARM ENFORCER E-9626-2B190Q Manual de usuario

Long-Range Barrier Sensors

Manual

Model

# of Beams

Length

E-9626-2B190Q

2 pairs

26” (66cm)

E-9643-4B190Q

4 pairs

43” (109cm)

E-9661-6B190Q

6 pairs

61” (155cm)

E-9679-8B190Q

8 pairs

79” (201cm)

4 Different programmable frequencies

Range: Up to 190ft (60m) outdoor,

380ft (120m) indoor

End caps swivel for easy installation

Built-in heater for cold weather

operation

Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.

Built-in tamper switches

Programmable trigger options

Form C relay output

Weatherproof IP65

AGC circuits ensure operation in rain,

fog, and low-temperature conditions

ENFORCER Long-Range Barrier Sensors

SECO-LARM U.S.A., Inc.

Table of Contents:

Introduction:

ENFORCER Long-Range Barrier Sensors are ideal for protecting indoor or outdoor areas

separated by long distances. They feature reliable photobeam technology with a choice of

four programmable beam frequencies that provide superior perimeter protection by

eliminating crosstalk and interference when multiple units are used. False alarms caused

by animals, falling leaves, poor weather, or other sources are minimized by programming

the alarm output trigger operation.

ENFORCER Long-Range Barrier Sensors work in even the most extreme conditions. A

built-in heater automatically turns on and off depending on the outside temperature. An

environmental control system senses a slow degradation in beam strength when weather

conditions worsen to help prevent false alarms.

Installation and alignment is quick and easy with the ENFORCER Long-Range Barrier

Sensors. They come with swiveling heads that allow them to be mounted along the same

wall or on opposite walls, as well as provide for easy alignment of the beams between the

transmitter and receiver.

Parts List:

Introduction.............................................2

Parts List ................................................2

Features .................................................3

Specifications .........................................3

Dimensions.............................................4

Swivel Housing.......................................4

Sample Applications...............................4

Overview –Inside the Sensor.................5

Installation –Choosing a Location..........6

Installation –Wall vs. Pole Mounting......7

Connecting Multiple Units ...................... 7

Installation –Running the Wires............. 8

Installation –Mounting .......................... 8

Installation –Connecting the Wires ....... 9

Aligning the Beams .............................. 10

Programming the Trigger Mode ........... 10

Programming the Barrier Sensor.......... 11

Triggering the Barrier Sensor............... 11

Troubleshooting ................................... 12

1 x Transmitter

1 x Receiver

1 x Manual

4 x Pole mount brackets

8 x Machine screws 4x6mm (for pole mount brackets)

8 x Machine screws 4x25mm (for pole mount brackets)

12 x Screws 6x20mm (for wall mount use)

12 x Plastic anchors (for wall mount use)

ENFORCER Long-Range Barrier Sensors

SECO-LARM U.S.A., Inc.

Features:

Specifications:

Model

E-9626-2B190Q

E-9643-4B190Q

E-9661-6B190Q

E-9679-8B190Q

Number of beams

2 pairs

4 pairs

6 pairs

8 pairs

Max. range (outdoor)

190’ (60m)

Max. range (indoor)

380’ (120m)

Tx standby & active current,

heater off (+/-25%@12VDC)

56mA

84mA

100mA

109mA

Rx standby current (buzzer

off),heater off (+/-25%@12VDC)

66mA

80mA

95mA

108mA

Rx trigger current (buzzer on)

heater off (+/-25%@12VDC)

66mA

80mA

95mA

108mA

Buzzer active current (Rx only)

20mA@12VDC

Heater active current (Rx+Tx)

160mA@12VDC

Input voltage

12~24 VDC

Response time (receiver)

150/300/450/600 ms (DIP switch programmable)

Detection methods

Triggers as programmed when any 2 adjacent pair of beams are broken, or any

single pair of beams is broken for over 2 sec. (programmable by JP2)

Selectable beam frequencies

4 Different frequencies (DIP switch programmable)

Alarm output

NO/NC/COM, relay output, active for 1 sec. when triggered

Tamper output (Tx & Rx)

1A@120VAC / 1A@24VDC

Alignment LED (Rx only)

Red LED, ON –beam is broken / OFF –aligned

Alignment angle

Horizontal +/-90O

Operating temperature

-45OC~55OC (-49OF~131OF)

Humidity

95%

Ingress protection

IP65

Case

Aluminum housing / PC anti-UV cover / ABS end caps

Dimensions

See page 4, Dimensions for more details

Weight (Tx & Rx) with brackets

5.5lb (2.5kg)

7.7lb (3.5kg)

12.1lb (5.5kg)

14.3lb (6.5kg)

For indoor or outdoor perimeter security

Long sensor range up to 190ft (60m)

outdoors, 380ft (120m) indoors

Install on windows, doorways, skylights,

fence tops, and any place where space

is limited

End caps swivel so sensor can be

mounted on a single wall or on opposite

walls with no L-bracket needed

Programmable immediate trigger on

simultaneous breaking of beams, or trigger

after a single pair of beams is broken for at

least 2 seconds

Heater for use in cold weather operation

Heater activates at 41°F (5°C)

Terminal block wiring

Slim design: 21/4” x 17/8” (55 x 49 mm)

Rugged aluminum construction

Built-in tamper switches, one on either end,

trigger the alarm if end cap is removed

No synchronizing wires required to align the

beams

Form C relay output

LED and buzzer alignment indicators

AGC (Auto Gain Control) circuits regulate

beam signals in order to compensate for

and ensure operation in rain, fog, and low-

temperature conditions

Programmable for 4 different frequencies to

reduce interference between

multiple units

ENFORCER Long-Range Barrier Sensors

SECO-LARM U.S.A., Inc.

Dimensions:

21/4”

(55mm)

17/8”

(49mm)

21/4”

(55mm)

17/8”

(49mm)

21/4”

(55mm)

17/8”

(49mm)

21/4”

(55mm)

17/8”

(49mm)

26”

(66cm)

43”

(109cm)

61”

(155cm)

79”

(201cm)

E-9626-2B190Q

E-9643-4B190Q

E-9661-6B190Q

E-9679-8B190Q

Swivel Housing:

Each sensor is built

with a swivel housing

for flexible installations

and simple alignment.

To use, twist the

beams up to 90.

Sample Applications:

Typical

door/window

frame

Windows

Fence tops

Garages,

gates, and

walls

1. Remove cap

2. Loosen

swivel head

screw

3. Turn sensor

to desired

position

4. Tighten screw

and replace

the end cap

ENFORCER Long-Range Barrier Sensors

SECO-LARM U.S.A., Inc.

Overview –Inside the Sensor:

Transmitter

Receiver

Power

Ground

Tamper output

Channel selection

switch (SW2)

Tamper switch

Rubber wire

hole

Tamper switch

Rubber wire

hole

Beam alignment

buzzer jumper (JP1)

Response time

switch (SW1)

Channel selection

switch (SW2)

Tamper switch

Power

Ground

Tamper

output

Tamper

switch

Beam trigger program

jumper (JP2)

Swivel screw

Red alignment/trigger

LED

COM

N.O.

N.C.

ENFORCER Long-Range Barrier Sensors

SECO-LARM U.S.A., Inc.

Installation –Choosing a Location:

When used outdoors, place the Long-Range Barrier Sensor under a roof or

shelter. This will reduce the chance of false alarms caused by rain or snow.

To prevent erratic operation and/or false alarms:

Do not mount near trees, bushes or

other leafy vegetation. Wind could

cause leaves or similar objects to fly or

wave into the beams (see Fig. 1).

Do not mount where water might run

off the roof and break the beam

(see Fig. 1).

Do not mount where the units could be

splashed by water or mud.

Do not let sunlight or any direct beam

of light shine directly on the sensor. If

unavoidable, mount in a way that the

transmitter –not the receiver –faces

the sun (see Fig. 2).

Mount the sensor so that the wires are

placed at the bottom. If the wires must

be placed on top, seal the opening

with silicone.

Do not mount in such a way that the

terminal block of one unit is at the top

and the other is at the bottom

(see Fig. 3).

Do not mount where animals or other

objects could accidentally break the

beams.

Do not mount near reflective surfaces,

as this could prevent the sensor from

working properly.

Do not mount where the unit could be

suddenly exposed to a bright light, such

as a floodlight or a passing

automobile’s headlight.

IMPORTANT: Do not connect to power until the sensor has been completely installed

and the installation has been double-checked.

Fig. 1 –Beware natural interference

Tree or shrub leaves

passing through beams

Rain running directly off

roof through beams

Fig. 2 –Orientation to the sun

Do not let sunlight or any direct beam of light shine

directly on the sensor. If unavoidable, mount in a

way that the transmitter –not the receiver –faces

the sun.

Fig. 3 –Orientation of the terminal

blocks

Mount so that the

terminal blocks of

both units are at the

top or both are at

the bottom. Do not

mount in such a

way that the

terminal block of

one unit is at the top

and the other is at

the bottom.

ENFORCER Long-Range Barrier Sensors

SECO-LARM U.S.A., Inc.

Connecting Multiple Units

CH 1 (TX)

CH 2 (RX)

CH 3 (RX)

CH 4 (TX)

CH 2 (TX)

CH 1 (RX)

CH 4 (RX)

CH 3 (TX)

Installation –Wall vs. Pole Mounting

Fig. 6 –Pole mounting

Fig. 4 –Wall mounting –Same wall

Fig. 5 –Wall mounting –Facing walls

Fig. 7 –Linear protection

CH1

CH3

CH2

CH4

Fig. 8 –Perimeter protection

(Pole-mount

brackets

included)

Machine screw

(4x6 mm)

Machine screw

(4x25 mm)

ENFORCER Long-Range Barrier Sensors

SECO-LARM U.S.A., Inc.

Installation –Mounting

1. Find a suitable location.

a. The transmitter and receiver can be mounted at any angle as long as they are

parallel to each other and directly facing each other, and as long as the wires come

out of the same ends of both units (see Fig. 3).

b. If using multiple curtain sensors, be sure to set each for a different frequency

(see pg. 11).

c. The transmitter and receiver must not be separated by more than 190ft (60m)

outdoors or 380ft (120m) indoors.

2. Mount the transmitter and the receiver in such a way that surface-mounted wires do not

come out from above the units. This is to prevent water from entering via the wire holes.

If this is unavoidable, use silicone to completely cover the area where the wires come

out the holes to prevent water from entering

3. Once a suitable mounting location has been

found, remove the covers of the end caps

and locate the three mounting holes (see

Fig. 10). Using these holes as a template,

mark their location on the wall with a pencil.

4. Connect the wires (see pg. 9) before

permanently mounting the units to the wall.

Installation –Running the Wires

1. Run six wires (1 x power, 1 x ground, 2 x alarm signal, and 2 x tamper switch) from the

alarm control panel to the receiver of the sensor. Shielded cable is strongly suggested.

2. Run four wires (1 x power, 1 x ground, and 2 x tamper switch) from the alarm control

panel to the transmitter of the sensor. Shielded cable is strongly suggested.

Note: It may be more convenient to connect the transmitter’s power and tamper wires to

the receiver’s power and tamper wires.

3. If burying the wires is required, make sure to run them through electrical conduit.

Shielded cable is strongly suggested.

4. If the wires are run along the wall, the use of armored cable is strongly suggested.

Voltage

Gauge

Max. length

12VDC

AWG 22

1,800ft (550m)

12VDC

AWG 20

2,600ft (800m)

24VDC

AWG 22

2,600ft (800m)

24VDC

AWG 20

3,900ft (1,200m)

Fig. 9 –Maximum wire lengths

Fig. 10 –Mounting

ENFORCER Long-Range Barrier Sensors

SECO-LARM U.S.A., Inc.

Installation –Connecting the Wires

1. Unscrew and pull the end cap off the side of the receiver with the terminal block

(see Fig. 11).

2. Run the wires through the rubber wire hole in the top corner of the back of the end cap.

3. Program the receiver (see pg. 11).

4. Replace the end cap. NOTE: End cap must be off when aligning the sensor.

5. Use a screwdriver to tighten the screws holding the end cap in place.

Receiver

1. Unscrew and pull the end cap off the side of the transmitter with the terminal block

(see Fig. 12).

2. Run the wires through the rubber wire hole in the top corner of the back of the end cap.

3. Program the transmitter.

4. Replace the end cap. NOTE: End cap must be off when aligning the sensor.

5. Use a screwdriver to tighten the screws holding the end cap in place.

Transmitter

Fig. 11 –Receiver circuit board

Fig. 12 –Transmitter circuit board

ENFORCER Long-Range Barrier Sensors

SECO-LARM U.S.A., Inc.

Aligning the Beams

1. To align the beams, loosen the swivel screw and adjust the beams to face each other.

Connect the power to the receiver and transmitter. If the beams are not aligned, the red

LED on the receiver will light ON (see Fig. 13).

2. For audible confirmation in addition to the LED, make sure jumper JP1 is plugged in on

the receiver’s circuit board. If the beams are not aligned, the receiver’s buzzer will

sound. To disable this feature, remove JP1 (see Fig. 14).

3. Once the beams are aligned, the red LED will turn off and the buzzer will not sound.

Programming the Trigger Mode

1. The default detection method is when any 2 adjacent pair of beams is broken, or when

any single pair of beams are broken more than 2 seconds (see Fig.19).

2. The latter (any single pair of beams broken) detection function can be disabled when

the JP2 jumper is removed.

Fig. 13 –Aligning the beams

Fig. 14 –Jumper position (JP1)

Alignment buzzer

OFF

Alignment buzzer

Fig. 15 –Programming buzzer ON/OFF

(JP1) and detection mode (JP2).

Fig. 16 –Jumper position (JP2)

Detection mode

OFF

Detection mode

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de SECO-LARM

SECO-LARM

SECO-LARM SD-927PWCQ Manual de usuario

SECO-LARM

SECO-LARM SD-9163-KSQ Manual de usuario

SECO-LARM

SECO-LARM Enforcer SD-927PKC-NEQ Manual de usuario

SECO-LARM

SECO-LARM ENFORCER SD-R400-BQ Manual de usuario

SECO-LARM

SECO-LARM ENFORCER E-931-S45RRQ Manual de usuario

SECO-LARM

SECO-LARM SD-9163-KSQ Manual de usuario

SECO-LARM

SECO-LARM ENFORCER E-961-S90WQ Manual de usuario

SECO-LARM

SECO-LARM SLI ENFORCER E-936-S45RRGQ Manual de usuario

SECO-LARM

SECO-LARM ENFORCER SM-205Q/W Manual de usuario

SECO-LARM

SECO-LARM Enforcer SM-205Q/W Manual de usuario

SECO-LARM

SECO-LARM ENFORCER CS-PD535-TAQ Manual de usuario

SECO-LARM

SECO-LARM ENFORCER E-931-S33PRGQ Manual de usuario

SECO-LARM

SECO-LARM E-931-S33PRQ Manual de usuario

SECO-LARM

SECO-LARM SLI ENFORCER E-931-S50RRGQ Manual de usuario

SECO-LARM

SECO-LARM Push-To-Exit Bar SD-969-A18 Manual de usuario

SECO-LARM

SECO-LARM SD-9163-KSQ Manual de usuario

SECO-LARM

SECO-LARM Enforcer SD-7251GCEX1Q Manual de usuario

SECO-LARM

SECO-LARM RA-4961-MBQ Manual de usuario

SECO-LARM

SECO-LARM ENFORCER SM-200Q/W Manual de usuario

SECO-LARM

SECO-LARM ENFORCER CS-PD115-PAQ Guía de instalación

SECO-LARM

SECO-LARM Push-to-Exit Bar SD-961A-36 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario