Sealey AK714.V2-01 Manual de usuario

INSTRUCTIONS FOR:

BLIND BEARING PULLER SET - 5PC

2. INTRODUCTION

1. SAFETY

3. CONTENTS

26mm - 32mm Attachment (Part No: AK714.V2-01)

20mm - 25mm Attachment (Part No: AK714.V2-02)

Slide hammer (Part No: AK714.V2-03)

15mm - 20mm Attachment (Part No: AK714.V2-04)

11mm - 15mm Attachment (Part No: AK714.V2-05)

WARNING! Ensure that Health and Safety, local authority and general workshop practice regulations are

adhered to when using this product.

DO NOT use this product if damaged.

Maintain product in good and clean condition for best and safest performance.

If the vehicle to be worked on is raised, ensure that it is adequately supported with axle stands or ramps and chocks.

Wear approved eye protection. A full range of personal safety equ

Wear suitable clothing to avoid snagging. Do not wear loose jewellery and tie back long hair.

Account for all tools and parts being used.

If working off the vehicle, secure the work piece in a vice or clamp it to a work bench.

DO NOT operate puller if you are tired or under the influence of alcohol, drugs or intoxicating medication.

 IMPORTANT: Always refer to the vehicle manufacturer’s service instructions, or a proprietary manual, to

establish the current procedure and data. These instructions are provided as a guide only.

2.1. Introduction

Fully chromed carbon steel medium stroke slide hammer. 370mm Overall length with 1.4kg hammer. Bearing

extractor collets with internal capacity from 11 to 32mm. Supplied in carry-case.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE

AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

ipment is available from your dealer.

4. INSTRUCTIONS

4.1. Prior to use of the required

attachment, disassemble and

grease as shown in fig.1.

Reassemble the attachment.

4.2. Screw the attachment into the

shaft, as shown in fig.2. Tighten

the attachment using a wrench.

Note: Do not over tighten.

4.3. Ensure the attachment jaws

are completely closed and insert

the attachment into the inner

diameter of the bearing, fig.3.

4.4 Turn the handle clockwise to

open the attachment jaws to

grip the bearing. See fig.4.

4.5. Hold the bearing puller as shown

in fig.5, slide the hammer to the

bearing end of the shaft and

then forcefully pull the hammer

to the other end of the shaft.

4.6. Ensure the bearing is being

pulled out evenly, if not, remove

the puller attachment and, using

a soft faced mallet, tap the

bearing until it is seated evenly.

4.7. Repeat paragraphs 4.5 and 4.6

until the bearing has been

removed.

4.8. Turn the handle anticlockwise to

close the jaws in order to

release the bearing from the

attachment head. See fig.5.

Loosen

Grease

Attachment Head

Fig.1

Tighten

Fig.2

Bearing

Attachment Head

Fig.3

Attachment Head

Hammer

Open jaws

Fig.4

Attachment Head

Hammer Close Jaws

Fig.5

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Sealey

Sealey

Sealey SA632 Manual de usuario

Sealey

Sealey YK20FAH.V3 Manual de usuario

Sealey

Sealey POWER TOOLS SA2004KIT Manual de usuario

Sealey

Sealey SLC2 Manual de usuario

Sealey

Sealey PSB05 Manual de usuario

Sealey

Sealey SMS2101 Manual de usuario

Sealey

Sealey SA20/S Manual de usuario

Sealey

Sealey SMART ERASER SA695 Manual de usuario

Sealey

Sealey SPR001 Manual de usuario

Sealey

Sealey STW300 Manual de usuario

Sealey

Sealey STW400 Manual de usuario

Sealey

Sealey E5188.V2 Manual de usuario

Sealey

Sealey PPFSG1 Manual de usuario

Sealey

Sealey SJS700.V2 Manual de usuario

Sealey

Sealey SX500 Manual de usuario

Sealey

Sealey YK10F.V3 Manual de usuario

Sealey

Sealey CP2612 Manual de usuario

Sealey

Sealey GSA53 Manual de usuario

Sealey

Sealey SB974.V5 Manual de usuario

Sealey

Sealey VS0204.V5 Manual de usuario

Sealey

Sealey VS7021.V4 Manual de usuario

Sealey

Sealey YK15FFP.V2 Manual de usuario

Sealey

Sealey VSE6160.V2 Manual de usuario

Sealey

Sealey Power Tools SA651.V3 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual