Sealey MS064 Manual de usuario
INSTRUCTIONS FOR
MOTORCYCLE DOLLY REAR WHEEL- LONG
SIDE STAND TYPE.
MODEL NO: MS064
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. Maintain the dolly in good condition (use an authorised service agent).
1.2. Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
1.3. Locate the dolly in a suitable work area. Keep area clean and tidy and free from unrelated materials, and ensure that there is adequate
lighting.
1.4. Ensure that the floor is level and strong enough (preferably concrete) to take the weight of the dolly and the motorcycle.
8DO NOT use the dolly on tarmacadam, as the surface may be unstable.
1.5. Keep the dolly clean for best and safest performance.
1.6. The maximum motorcycle weight is 300kg. DO NOT exceed this rated capacity.
1.7. Use appropriate straps to secure the motorcycle to the dolly when manoeuvring.
1.8. Pull rather than push the motorcycle when manoeuvring on the dolly to reduce the risk of pushing the motorcycle off its side stand.
1.9. Maintain correct balance and footing, DO NOT over reach. Ensure the floor is not slippery and wear non-slip shoes. Keep children and
unauthorised persons away from the work area.
8DO NOT use the dolly for a task it is not designed to perform.
8DO NOT use the dolly if it is damaged.
8DO NOT use the dolly when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8DO NOT allow untrained persons to use the dolly.
8DO NOT make any modifications to the dolly.
1.10. Before storing in safe area, ensure that all parts are clean and free of grease and oil.
WARNING: The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may occur.
It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the
operator.
2. INTRODUCTION
Motorcycle dolly holds a single motorcycle or sports bike with side stand, weighing up to 300Kg. Enabling easy manoeuvrability around the
workshop or garage. The front wheel stays in contact with the ground allowing the motorcycle to be steered into the desired position. Pivoting
design allows exibility in side stand designs.
3. SPECIFICATION
Model No....................................................................MS064
Max. Capacity ..............................................................300Kg
Overall Dimensions (LxW).................................1260x555mm
Rear Wheel Loading Tray Dimensions ................400x250mm
MS064| Issue 1 16/03/16
Original Language Version
© Jack Sealey Limited
Refer to
Instruction
Manual
Fig.1
4. ASSEMBLY
Part
No..
Description QTY.
1. Main Part 1.
2. Aluminium Plate 1.
3. Nut with Cap 6.
4. Spring Washers 6.
5. Flat Washer 6.
6. Wheels With Brake 2.
7. M12 Set Screw 1.
8. Supporting Arm 1.
9. Aluminium Plate 1.
10. Wheels Without Brake 3.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Sole UK Distributor, Sealey Group.
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk.
IP32 7AR
www.sealey.co.uk
sales@sealey.co.uk
01284 757500
01284 703534
Web
MS064 | Issue 1 16/03/16
Original Language Version
© Jack Sealey Limited
Fig.2
4.1. Remove with care all contents from outer packaging and check parts against parts list. Ref. to g.2
4.2. Place main part (1) on ground attach 2 Wheels with brakes (6) using Flat Washers(5), Spring Washers(4) and nuts with cap(3).
4.3. Attach 2 Wheels(10) using Flat Washers(5), Spring Washers(4) and nuts with cap(3).
4.4. Place Supporting Arm(8) on ground attach Wheel(10) using Flat Washer(5), Spring Washer(4) and nut with cap(3).
4.5. Using M12 Set Screw, bolt Main Part(1) and Support Arm(8) together. The support arm can move in relatoionship to main part and can
be adjusted to position/design of side stand before bolt being thightened fully.
5. OPERATION
WARNING! Ensure that you read, understand and apply
the safety instructions before use.
WARNING! DO NOT attempt to overload the dolly.
5.1. Loading.
5.1.1. Position the dolly in a suitable area, checking that the surface
on which the dolly will be used is solid and flat.
5.1.2. Apply the brakes to the two wheels
5.1.3. Push the motorcycle on to the dolly positioning the rear wheel
centrally on the main part and support with the side stand on
the support arm adjust as required and fix in position by
tightening set screw. Front wheel remains on ground.
5.1.4. Release the brakes to allow the dolly to be manoeuvred.
5.2. Unloading
5.2.1. Apply the brakes to the two wheels.
5.2.2. Holding handle bars lift side stand and remove the motorcycle
from the dolly.
5.2.3. Store the dolly in a safe, dry, childproof location with the
brakes on.
6. MAINTENANCE
6.1. Before use, check the frame assembly and platform for cracks and damage.
6.2. Regularly check that all fasteners are tight.
6.3. Periodically lubricate the castors
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
Note: Image Shows MS063A
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
Tabla de contenidos
Otros manuales de Sistema de elevación de Sealey
Sealey
Sealey MT500 Manual de usuario
Sealey
Sealey ES502.V2 Manual de usuario
Sealey
Sealey MT680 Manual de usuario
Sealey
Sealey Quality MACHINERY MC550 Manual de usuario
Sealey
Sealey MC480.V3 Manual de usuario
Sealey
Sealey HPT300 Manual de usuario
Sealey
Sealey FCR500 Manual de usuario
Sealey
Sealey MC390AH Manual de usuario
Sealey
Sealey MC455.V2 Manual de usuario
Sealey
Sealey HPT400H.V2 Manual de usuario
Sealey
Sealey MC365A Manual de usuario
Sealey
Sealey AVR2500A Manual de usuario
Sealey
Sealey MC450 Manual de usuario
Sealey
Sealey 1250CX Manual de usuario
Sealey
Sealey AK98943 Manual de usuario
Sealey
Sealey WD80 Manual de usuario
Sealey
Sealey MT680.V3 Manual de usuario
Sealey
Sealey ES502.V2 Manual de usuario
Sealey
Sealey WD80 Manual de usuario
Sealey
Sealey EVBT1000 Manual de usuario
Manuales populares de Sistema de elevación de otras marcas
morse
morse 82H-124 Manual de usuario
Braun
Braun NL955 Series Manual de usuario
haacon
haacon 1889.10 Manual de usuario
Protekt
Protekt AT 252 Manual de usuario
R. Beck Maschinenbau
R. Beck Maschinenbau HS 600 Manual de usuario
Nova Technology International, LLC
Nova Technology International, LLC NAS Series Manual de usuario
Genie
Genie Z-60/34 Manual de usuario
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manual de usuario
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manual de usuario
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manual de programación
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manual de programación
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manual de programación
