Seagull BC-12D Manual de usuario
WWW.SEAGULLMODELS.COM
1
www.seagullmodels.com
Specications:
Wingspan---------------62.0 in (157.5 cm).
Wing area----------------620 sq.in (40.0 sq.dm).
Weight-------------------3.3 - 3.9 lbs (1.5 - 1.8 kg).
Length-------------------40.9 in (103.8cm).
Motor-------------------.25-.32 brushless motor.
Radio--------------------4 channels with 4 servos.
Electric conversion: Optional.
MS: 193
“ Graphics and specications may change without notice “ .
ARF
ASSEMBLY MANUAL
TAYLOR CRAFT 25E Instruction Manual.
2
ank you for choosing the ARTF by SEAGULL MODELS COMPANY LTD,. e
. was designed with the intermediate/advanced sport yer in mind. It is a semi scale
airplane which is easy to y and quick to assemble. e airframe is onventionally built using
balsa, plywood to make it stronger than the average ARTF, yet the design allows the aeroplane
to be kept light. You will nd that most of the work has been done for you already. e motor
mount has been tted and the hinges are pre-installed. Flying the is simply a joy.
is instruction manual is designed to help you build a great ying earoplane. Please read
this manual throughly before starting assembly of your . User the parts listing
below to indentify all parts.
INTRODUCTION.
WARNING.
KIT CONTENTS
1
2
33
6
7
4
5
2
Please be awere that this aeroplane is not a toy and if assemble or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & REPONSIBILITY.
If you are inexperienced with basic RC ight we strongly recommend you contact your RC
supplier and join your local RC model Flying Club. RC Model Flying Clubs oer a variety of
training procedures designed to help the new pilot on his way to successful RC ight. ey
will also be able to advise on any insurance and safety regulations that may apply.
WWW.SEAGULLMODELS.COM
3
KIT CONTENTS.
SEA19301 Fuselage
SEA19302 Wing set
SEA19303 Tail set
SEA19304 Canopy Hatch
SEA19305 Cowling
SEA19306 Wing tube
SEA19307 Pilot
TOOLS & SUPPLIES NEEDED.
ick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modelling knife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
read-lock.
Paper towels.
HINGING THE AILERONS.
Note : e control surfaces, including the ai-
lerons, elevators, and rudder, are prehinged
with hinges installed, but the hinges are not
glued in place. It is imperative that you prop-
erly adhere the hinges in place per the steps
that follow using a high-quality thin C/A glue.
1) Carefully remove the aileron from one
of the wing panels. Note the position of the
hinges.
2) Remove each hinge from the wing panel
and aileron and place a T-pin in the center of
each hinge. Slide each hinge into the aileron
until the T-pin is snug against the aileron.
is will help ensure an equal amount of
hinge is on either side of the hinge line when
the aileron is mounted to the wing panel.
3) Slide the aileron on the wing panel until
there is only a slight gap. e hinge is now
centered on the wing panel and aileron. Re-
move the T-pins and snug the aileron against
the wing panel. A gap of 1/64” or less should
be maintained between the wing panel and
aileron.
.
Hinge.
T-pin.
TAYLOR CRAFT 25E Instruction Manual.
4
4) Deect the aileron and completely satu-
rate each hinge with thin C/A glue. e ailer-
ons front surface should lightly contact the
wing during this procedure. Ideally, when
the hinges are glued in place, a 1/64” gap or
less will be maintained throughout the lengh
of the aileron to the wing panel hinge line.
NOTE : e hinge is constructed of a spe-
cial material that allows the C/A to wick
or penetrate and distribute throughout
the hinge, securely bonding it to the wood
structure of the wing panel and aileron.
Hinge.
Epoxy.
5) Turn the wing panel over and deect the
aileron in the opposite direction from the
opposite side. Apply thin C/A glue to each
hinge, making sure that the C/A penetrates
into both the aileron and wing panel.
6) Using C/A remover/debonder and a pa-
per towel, remove any excess C/A glue that
may have accumulated on the wing or in the
aileron hinge area.
7) Repeat this process with the other wing
panel, securely hinging the aileron in place.
8) Aer both ailerons are securely hinged,
rmly grasp the wing panel and aileron to
make sure the hinges are securely glued and
cannot be pulled out. Do this by carefully ap-
plying medium pressure, trying to separate
the aileron from the wing panel. Use caution
not to crush the wing structure.
Work the aileron up and down sev-
eral times to “work in” the hinges
and check for proper movement.
Note :
WWW.SEAGULLMODELS.COM
5
HINGING THE ELEVATORS.
1) Locate the item for this sectiom of the
manual.
2) Carefully remove the elevator from
one of the horizontal stabilizer panels.
Note the position of the hinges.
3) Remove each hinge from the hori-
zontal stabilizer panel and elevator
and place a T-pin in the center of each
hinge. Slide each hinge into the eleva-
tor until the T-pi n is snug against the
elevator. is will help ensure an equal
amount of hinge is on either side of the
hinge line when the elevator is mount-
ed to the horizontal stabilizer panel.
Glue the hinge hinges in place using the
same techniques used to hing the ailerons.
Epoxy.
HINGING THE RUDDER.
Glue the rudder hinges in place using
the same techniques used to hinge the ai-
lerons.
Locate the hardware necessary to install
the control horns for the ailerons.
INSTALL THE AILERON CONTROL
HORN.
Aileron control horn.
Epoxy.
Epoxy.
TAYLOR CRAFT 25E Instruction Manual.
6
Install the elevator control horn using
the same method as same as the aileron
control horns.
INSTALL ELEVATOR CONTROL HORN.
.
Elevator control horn.
Epoxy.
Elevator.
Epoxy.
Epoxy.
Rudder control horn.
INSTALL RUDDER CONTROL HORN.
Repeat steps to install the rudder control
horn as same as steps done for ailerons.
Rudder control horn.
Back.
Front.
Le.
Right.
WWW.SEAGULLMODELS.COM
7
INSTALLING THE MAIN LANDING
GEAR TO FUSELAGE.
read a mounting screw into each of
the holes to cut threads in the surround-
ing wood. Apply a small amount of thin
CA to harden the threads make by the
screws. Position the landing gear so it
rakes forward. Use the screws and land-
ing gear straps to secure the landing gear
to the bottom of the fuselage.
3x10mm
Fit the wheel pant on the axle. Slide the
wheel collar onthe axle and temporarily
secure the collar ush with the end of the
axle.
Slide the wheel pant and wheel onthe
landing gear. With both wheels and pants
place, rest the fuselage on the at surface.
Check that there is clearance between the
surface and wheel pant. Tighten the set-
screws so they leave marks on the axle.
Collar.
Collar.
3x6mm
TAYLOR CRAFT 25E Instruction Manual.
8
Rudder.
Elevator.
SERVO ARM INSTALLATION.
Install adjustable servo connector in the
servo arm as same as picture below:
ELECTRIC POWER .
Repeat steps to prepare and place the
opposite wheel pant on the landing
gear.
INSTALLING THE FUSELAGE SERVOS.
.
Because the size of servos dier, you
may need to adjust the size of the precut
opening in the mount. e notch in the
sides of the mount allow the servo lead to
pass through.
1) Install the rubber grommets and brass
collets onto the fuselage servo. Test t the
servo into the aileron servo mount.
2) Secure the servos with the screws pro-
vided with your radio system.
Rudder.
Elevator.
3x10mm
1) Secure the motor to the motor box us-
ing the hardware listed.
3x6mm
WWW.SEAGULLMODELS.COM
9
2) Connect the leads from the motor to
the speed control. Use hook and loop
tape to mount the speed control in the
fuselage. Make sure to the position the
speed control far enough into the fuse-
lage so the lead from the speed control
can be connected to the receiver. Use tie-
wraps to secure the wiring so it doesn’t
interfere with the operation of the motor.
Speed control.
COWLING.
1) Slide the berglass cowl over the en-
gine and line up the back edge of the cowl
with the marks you made on the fuselage
then trim and cut as shown.
2) While keeping the back edge of the
cowl ush with the marks, align the front
of the cowl with the cranksha of the
engine. e front of the cowl should be
positioned so the cranksha is in near-
ly the middle of the cowl opening. Use
the spinner backplate as a guide. Hold
the cowl rmly in place using pieces of
masking tape.
TAYLOR CRAFT 25E Instruction Manual.
10
3x10mm
3) Install the muer and muer extension
onto the engine and make the cutout in the
cowl for muer clearance. Connect the fuel
and pressure lines to the carburetor, muer
and fuel ller valve. Secure the cowl to fuse-
lage using the M3x10mm screws.
Install the spinner backplate, propeller
and spinner cone.
INSTALLING THE SPINNER.
e propeller should not touch any
part of the spinner cone. If it does, use a
sharp modeling knife and carefully trim
away the spinner cone where the propel-
ler comes in contact with it.
INSTALLING THE AILERON SERVOS.
Servos
.
Small weight
.
Thread
Because the size of servos dier, you
may need to adjust the size of the precut
opening in the mount. e notch in the
sides of the mount allow the servo lead to
pass through.
1) Using a small weight (Weighted fuel
pick-up works well) and string, feed the
string through the wing as indicated.
2) Place the servo between the mount-
ing blocks and space it from the hatch.
Use a pencil to mark the mounting hole
locations on the blocks.
Tabla de contenidos
Otros manuales de Juguete de Seagull
Seagull
Seagull cassutt 3M Racer Manual de usuario
Seagull
Seagull Space Walker II Manual de usuario
Seagull
Seagull Space Walker II Manual de usuario
Seagull
Seagull SEA238 Manual de usuario
Seagull
Seagull SEA53B Manual de usuario
Seagull
Seagull X-RAY Manual de usuario
Seagull
Seagull Fair Child PT19 Manual de usuario
