Seagate Medalist Pro 2160N Manual de usuario
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Medalist Pro 2160N (ST52160N)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCSI Hard Drive
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
-2 Medalist Pro 2160N, Rev. B
© 1997–1999 Seagate Technology, Inc. All rights reserved.
Publication Number: 32653-001, Rev. B, September 1999
Seagate, Seagate Technology and the Seagate logo are regis-
tered trademarks of Seagate Technology, Inc. Medalist, SeaFAX,
SeaFONE, SeaBOARD and SeaTDD are either trademarks or
registered trademarks of Seagate Technology, Inc. or one of its
subsidiaries. All other trademarks or registered trademarks are
the property of their respective owners.
Medalist Pro 2160N, Rev. B -1
Contents
What you need........................................................................ 1
Before you begin .................................................................... 1
Handling precautions............................................................. 2
SCSI ID jumpers and drive termination................................ 3
Setting the SCSI ID ............................................................ 3
SCSI termination ................................................................ 5
Attaching cables and mounting the drive............................ 7
Configuring your computer................................................. 11
Partitioning and formatting your drive............................... 12
Low level format................................................................ 12
DOS, Windows 95, Windows NT and OS/2...................... 12
Other operating systems................................................... 14
Additional drive options ...................................................... 15
Troubleshooting ................................................................... 17
Drive specifications ............................................................. 23
Glossary................................................................................ 24
Seagate Technology support services............................... 25
Storing and shipping your drive......................................... 32
iii
0 Medalist Pro 2160N, Rev. B
iv
Medalist Pro 2160N, Rev. B 1
What you need
•Straight-edge and Phillips screwdrivers
•Drive mounting screws
•A SCSI interface host adapter
•A 50-pin SCSI interface cable
•An unused drive power cable for your new drive
•A DOS or Windows 95 system setup diskette (Seagate recom-
mends using DOS Version 5.0 or later).
•If you are mounting this 3.5-inch drive in a 5.25-inch drive bay,
you need a mounting adapter or frame kit. Also, you may need
drive mounting rails if your drive bay is not designed for direct
mounting.
Before you begin
•Make sure your computer is turned off before you open the
case.
•Read the handling precautions following and inspect the drive
to make sure that it is not damaged.
•Save your foam-lined Seagatedisc drive box. This box has
been approved by Seagate for shipping a Seagate disc drive.
Using any other container or packing material voids your drive
warranty.
2 Medalist Pro 2160N, Rev. B
Handling precautions
Disc drives are extremely fragile. Do not drop or jar
your drive.
Keep the drive in its antistatic bag until you are
ready to install it.
Protect your drive from static discharge by making
sure you are well grounded before touching the
drive. We recommend wearing a grounded wrist
strap throughout the installation process. Do not
touch the connectors or any part of the printed cir-
cuit board.
Always handle the drive by its edges or frame.
Do not apply pressure or attach labels to the circuit
board or the top of the drive.
Medalist Pro 2160N, Rev. B 3
SCSI ID jumpers and drive termination
Setting the SCSI ID
Your SCSI drive is configured at the factory as SCSI ID 0 (no
jumpers installed). If you are installing only one drive or if this will
be your boot drive, the drive should be configured as SCSI ID 0.
Each device on the SCSI chain must have a unique SCSI ID. If
you are installing a second hard drive, choose the next available
ID. SCSI ID 7 is usually reserved for the SCSI host adapter.
Figure 1 on page 4 shows the jumper settings for SCSI IDs 0
through 7.
4 Medalist Pro 2160N, Rev. B
Figure 1. SCSI ID and termination jumper settings
SCSI ID 1
SCSI ID 2
Terminator
Enabled
SCSI ID 0
SCSI ID 3
SCSI ID 4
SCSI ID 5
SCSI ID 6
SCSI ID 7
Terminator
Disabled
1197531
1210 8 6 4 2
13
14
Medalist Pro 2160N, Rev. B 5
SCSI termination
Figure 2. Termination for internal SCSI devices
Chains of SCSI devices must be terminated at each end of the
cable.
The figure above shows two internal hard drives with the termi-
nation enabled for the SCSI host adapter and the last device on
the cable.
If your new drive is the last device on the SCSI cable, you must
enable termination. Active termination is enabled when there are
no jumpers on pins 11 and 12 of the options jumper block. This
is the default setting.
If your drive is not the last device on the SCSI cable, SCSI termi-
nation must be disabled by placing a jumper on pins 11 and 12.
Internal SCSI device
Internal SCSI device
SCSI Host Adapter
Terminate
Terminate
6 Medalist Pro 2160N, Rev. B
Figure 3. Termination for internal and external SCSI devices
This figure shows a SCSI chain with two internal SCSI devices
and two external SCSI devices. The SCSI devices at the ends of
each cable are terminated.
Note. Some SCSI host adapters should remain terminated
even if they are in the middle of the chain. Also, some
adapters treat the internal and external chains as sepa-
rate logical buses. This means you may need to termi-
nate both the first and last devices on both logical buses
to achieve proper termination. Refer to your computer or
host adapter documentation to see how this is handled in
your system.
Internal SCSI device
Internal SCSI device
External SCSI device
External SCSI device
SCSI Host Adapter
Terminate
Terminate
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Almacenamiento de Seagate
Seagate
Seagate ST31081A Manual de usuario
Seagate
Seagate ST32430N Manual de usuario
Seagate
Seagate CHEETAH 9 ST19101N/W/WC/WD/DC Manual de usuario
Seagate
Seagate ST2000VX000 Manual de usuario
Seagate
Seagate ST318405LW/LC Manual de usuario
Seagate
Seagate MOMENTUS ST91603010AS Manual de usuario
Seagate
Seagate Backup Plus Desktop Manual de usuario
Seagate
Seagate Momentus ST9808211A Manual de usuario
Seagate
Seagate EXOS ENTERPRISE 2X18 SAS 512E Standard Manual de usuario
Seagate
Seagate ST34501N Manual de usuario
Seagate
Seagate ST9120315AS - Momentus 5400.6 120 GB Hard... Manual de usuario
Seagate
Seagate ST5000DM000 Manual de usuario
Seagate
Seagate U Series 9 CE Manual de usuario
Seagate
Seagate ST6000NM0004 Manual de usuario
Seagate
Seagate ST446452W Manual de usuario
Seagate
Seagate Expansion Portable Drive 1TB Manual de usuario
Seagate
Seagate ST3500641NS Manual de usuario
Seagate
Seagate BlackArmor WS 110 Manual de usuario
Seagate
Seagate FreeAgent GoFlex TV Manual de usuario
Seagate
Seagate Momentus ST91008220AS Manual de usuario
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario