Seagate ST500UM001 Manual de usuario

100725146, Rev. E

Gen 1 - September 2015

Standard models

ST500UM001

ST320UM001

Laptop Thin SSHD

SATA Product Manual

Publication number: 100725146, Rev. E September 2015

Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. 3D Defense System and SeaTools are

either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or registered

trademarks are the property of their respective owners.

No part of this publication may be reproduced in any form without written permission of Seagate Technology LLC.

Call 877-PUB-TEK1(877-782-8351) to request permission.

When referring to drive capacity, one gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your computer’s operating system may use a different

standard of measurement and report a lower capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data storage.

Actual quantities will vary based on various factors, including file size, file format, features and application software. Actual data rates may vary depending on operating environment

and other factors. The export or re-export of hardware or software containing encryption may be regulated by the U.S. Department of Commerce, Bureau of Industry and Security (for

more information, visit www.bis.doc.gov), and controlled for import and use outside of the U.S. Seagate reserves the right to change, without notice, product offerings or specifications.

Document Revision History

Revision Date Pages affected

Rev. A 07/09/2013 Initial release.

Rev. B 01/16/2014 5 & 12.

Rev. C 05/05/2014 5, 12 & 16.

Rev. D 06/24/2014 6.

Rev. E 09/30/2015 FC, 4, 7, 13 & BC

Seagate Laptop Thin SSHD SATA Product Manual, Rev. E 2

Contents

Seagate® Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 About the Serial ATA Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2.0 Drive Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Formatted Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

2.1.1 LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

2.2 Physical organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

2.3 Recording and Interface Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

2.4 Physical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

2.5 Seek time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

2.6 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

2.7 Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

2.7.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

2.7.2 Conducted noise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

2.7.3 Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

2.7.4 Power management modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

2.8 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

2.8.1 Shock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

2.8.2 Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

2.9 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

2.9.1 Test for prominent discrete tones (PDTs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

2.10 Electromagnetic Immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

2.11 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

2.12 Agency Certification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

2.12.1 Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

2.12.2 Electromagnetic Compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

2.12.3 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

2.13 Environmental Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

2.13.1 European Union Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . .15

2.13.2 China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . . . . . . . . . . . .15

2.14 Corrosive Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

3.0 Configuring and Mounting the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.1 Handling and Static-Discharge Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

3.2 Configuring the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

3.2.1 Serial ATA Cables and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

3.3 Drive Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

4.0 Serial ATA (SATA) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.1 Hot-Plug Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

4.2 Serial ATA Device Plug Connector Pin Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

4.3 Supported ATA Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

4.3.1 Identify Device command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

4.3.2 Set Features command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

4.3.3 S.M.A.R.T. commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Seagate Laptop Thin SSHD SATA Product Manual, Rev. E 3

Figures

Figure 1 Typical 5V Startup and Operation Current Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Figure 2 Attaching SATA Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 3 Mounting Dimensions (for standard models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Seagate Laptop Thin SSHD SATA Product Manual, Rev. E 4

For information regarding online support and services, visit: http://www.seagate.com/contacts/

For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/

For information regarding data recovery services, visit: http://www.seagate.com/services-software/seagate-recovery-

services/recover/

For Seagate OEM, Distribution partner portal and reseller portal, visit: http://www.seagate.com/partners/

Seagate®Technology Support Services

Seagate Laptop Thin SSHD SATA Product Manual, Rev. E 5

Introduction

1.0 Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate®Laptop Thin SSHD model drives:

These drives provide the following key features:

5400-RPM spindle speed.

64MB buffer.

16GB NAND flash

Quiet operation. Fluid Dynamic Bearing (FDB) motor.

High instantaneous (burst) data-transfer rates (up to 6Gb/s).

Perpendicular recording technology.

State-of-the-art cache and on-the-fly error-correction algorithms.

Native Command Queuing (NCQ) with command ordering.

Full-track multiple-sector transfer capability without local processor intervention.

1000 Gs nonoperating shock and 350 Gs of operating shock.

SeaToolsTM diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

The 3D Defense System™, which includes Drive Defense, Data Defense and Diagnostic Defense,

offers the industry’s most comprehensive protection for disk drives.

Support for S.M.A.R.T. drive monitoring and reporting.

Support for Read Multiple and Write Multiple commands.

Worldwide Name (WWN) capability uniquely identifies the drive.

1.1 About the Serial ATA Interface

The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include:

Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other configuration options.

Thinner and more flexible cabling for improved enclosure airflow and ease of installation.

Scalability to higher performance levels.

In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial ATA was designed to allow users to

install a Serial ATA host adapter and Serial ATA disk drive in the current system and expect all of the existing applications to work as normal.

The Serial ATA interface connects each disk drive in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave

relationship with Serial ATA devices like there is with parallel ATA. If two drives are attached on one Serial ATA host adapter, the host operating

system views the two devices as if they were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0

(master) devices.

The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward compatibility with existing

host systems and software. The Command and Control Block registers, PIO and DMA data transfers, resets, and interrupts are all emulated.

The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device registers, referred to as the Shadow

Register Block. All Serial ATA devices behave like Device 0 devices. For additional information about how Serial ATA emulates parallel ATA, refer to

the Serial ATA International Organization: Serial ATA (Revision 2.6). The specification can be downloaded from www.serialata.org.

Standard models

ST500UM001

ST320UM001

NOTE

For improved reliability, Seagate SSHDs incorporate a technique referred

to as 'Combo Mode', utilizing proprietary controls to reduce the number

of bits stored to a portion of the NAND Flash.

NOTE

The host adapter may, optionally, emulate a master/slave environment to host software where two devices

on separate Serial ATA ports are represented to host software as a Device 0 (master) and Device 1 (slave)

accessed at the same set of host bus addresses. A host adapter that emulates a master/slave environment

manages two sets of shadow registers. This is not a typical Serial ATA environment.

Seagate Laptop Thin SSHD SATA Product Manual, Rev. E 6

Drive Specifications

2.0 Drive Specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the

drive and this drive are used throughout this manual to indicate the following drive models:

The specification summaries listed in the following tables are for quick reference. For details on specification measurement or definition, refer to the

appropriate section of this manual.

Table 1 Drive Specifications Summary

Drive Specification ST500UM001 ST320UM001

Formatted capacity (1) 500 GB 320 GB

Guaranteed sectors 976,773,168 625,142,448

Heads 2

Disks 1

Bytes per sector 512 (logical) / 4096 (physical)

Recording density 1894 Kb/in

Track density 375 Ktracks/in avg

Areal density 705 Gb/in2 avg

Spindle speed 5400 RPM

Sustained data transfer rate OD 100 MB/s max

I/O data-transfer rate 600 MB/s max

ATA data-transfer modes supported

PIO modes 0–4

Multiword DMA modes 0–2

Ultra DMA modes 0–6

Cache buffer 64 MB

NAND flash

Commercial Multilevel Cell (cMLC) 16GB

Height 6.8 +/- 0.2 mm (0.268 +/-.008 in)

Width 69.85 +/- 0.25 mm (2.750 +/- 0.010 in)

Length 100.35 +0.20 / -0.25 mm (3.951 +0.008 / -0.010 in)

Weight (typical) 95 g (0.209 lb)

Average latency 5.6 ms

Startup current (typical) 5V (peak) 1.0 A

Voltage tolerance (including noise) 5V ± 5%

Operating temperature 0° to 60°C

Nonoperating temperature (Ambient) –40° to 70°C

Temperature gradient (max) 20°C per hour max (operating)

35°C per hour max (nonoperating)

Relative humidity 5% to 95% (operating)

5% to 95% (nonoperating)

Relative humidity gradient 30% per hour max

Wet bulb temperature (max) 37.7°C max (operating)

40.0°C max (nonoperating)

Altitude, operating –304.8 m to 3048 m (–1000 ft to 10,000+ ft)

Seagate Laptop Thin SSHD SATA Product Manual, Rev. E 7

Drive Specifications

2.1 Formatted Capacity

2.1.1 LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed

sectors as defined above.

Refer to Configuring and Mounting the Drive on page 16 (words 60-61 and 100-103) for additional information about 48-bit addressing support

of drives with capacities over 137 GB.

Altitude, nonoperating

(below mean sea level, max) –304.8 m to 12,192 m (–1000 ft to 40,000+ ft)

Operational Shock 350 Gs at 2 ms max

Non-Operational Shock 1000 Gs at 1 ms max

Vibration, operating 5–200 Hz: 2.0 Gs

201–500 Hz: 1.0 Gs

Vibration, nonoperating 5–500 Hz: 5.0 Gs

Nonrecoverable read errors 1 per 1015 bits read

Annualized Failure Rate (AFR) 1%

Rated workload

Average annualized workload rating: <55 TB/year.

The AFR specification for the product assumes the I/O workload does not exceed the average annu-

alized workload rate limit of 55 TB/year. Workloads exceeding the annualized rate may degrade the

product AFR and impact reliability as experienced by the particular application. The average annual-

ized workload rate limit is in units of TB per calendar year.

Warranty

To determine the warranty for a specific drive, use a web browser to access the following web page:

http://www.seagate.com/support/warranty-and-replacements/.

From this page, click on the “Is my Drive under Warranty” link. The following are required to be pro-

vided: the drive serial number, model number (or part number) and country of purchase. The sys-

tem will display the warranty information for the drive.

Load-unload cycles 600,000 at 25°C, 50% rel. humidity

Supports Hotplug operation per the

Serial ATA Revision 2.6 specification Yes

1. One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.

Model Formatted Capacity(1)

1. One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and

formatting.

Guaranteed Sectors Bytes per Sector

500GB model 500 GB 976,773,168

512 (logical) / 4096 (physical)

320GB model 320 GB 625,142,448

Table 1 Drive Specifications Summary (continued)

Drive Specification ST500UM001 ST320UM001

Seagate Laptop Thin SSHD SATA Product Manual, Rev. E 8

Drive Specifications

2.2 Physical organization

2.3 Recording and Interface Technology

2.4 Physical Characteristics

2.5 Seek time

Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications

in the table below are defined as follows:

Track-to-track seek time is an average of all possible single-track seeks in both directions.

Average seek time is a true statistical random average of at least 5000 measurements of seeks between random tracks, less overhead.

Drive model Read/write heads Number of discs

ST500UM001

2 1

ST320UM001

Inter face Serial ATA (SATA)

Recording method Perpendicular

Recording density 1894 Kb/in

Track density 375 ktracks/in avg

Areal density 705 Gb/in2 avg

Spindle speed 5400 RPM +/- 0.2%

Sustained data transfer rate 100 MB/s max

I/O data-transfer rate 600 MB/s max

All models

Height 6.8 +/- 0.2 mm (0.370 +/-.008 in)

Width 69.85 +/- 0.25 mm (2.750 +/- 0.010 in)

Length 100.35 +0.20 / -0.25 mm (3.951 +0.008 / -0.010 in)

Typical weight 95 g (0.209 lb)

Cache buffer 64 MB (64,768 KB)

Table 2 Typical seek times

Typical seek times (ms) Read

Track-to-track 2.0

Average 12.0

Average latency 5.6

NOTE

These drives are designed to consistently meet the seek times represented in this manual.

Physical seeks, regardless of mode (such as track-to-track and average), are expected to meet the

noted values. However, due to the manner in which these drives are formatted, benchmark tests

that include command overhead or measure logical seeks may produce results that vary from

these specifications.

Seagate Laptop Thin SSHD SATA Product Manual, Rev. E 9

Drive Specifications

2.6 Start/stop times

2.7 Power Specifications

The drive receives DC power (+5V) through a native SATA power connector (refer to Figure 2).

2.7.1 Power consumption

Power requirements for the drives are listed in the table in Table 4. Typical power measurements are based on an average of drives tested, under

nominal conditions, at 25°C ambient temperature. These power measurements are done with Interface Power Management modes like HIPM

and DIPM enabled.

Spinup power

Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.

Seek mode

During seek mode, the read/write actuator arm moves toward a specific position on the disk surface and does not execute a read or write

operation. Servo electronics are active. Seek mode power is measured based on three random seek operations every 100 ms. This mode is not

typical.

Read/write power and current

Read/write power is measured with the heads on track, based on three 63 sector read or write operations every 100 ms.

Idle mode power

Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in a random track location.

Standby mode

During standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/write electronics are in power-down

mode.

Table 3 Start/stop times

Typical seek times (ms) Typical Max @ 25°C

Power-on to ready (sec) <1.0 <1.0

Standby to ready (sec) <1.0 <1.0

Table 4 DC Power Requirements

Power Dissipation +5V Input Average (25° C)

Spinup (max) 1.50A

Seek average 2.5W

Write average 3.5W

Read average 2.9W

Idle, performance (1)

1. During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which

may increase acoustic and power to operational levels.

1.5W

Idle, active 1.0W

Idle, low power mode 0.9W

Standby(2)

2. Standby power is measured at steady state (after 200ms from transition)

0.53W

Sleep 0.53W

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de estado sólido de Seagate

Seagate

Seagate ST400FM0323 Manual de usuario