SEA MARK TANK E 270 Manual de usuario

REV 00 - 07/2013

HYDRAULIC OPERATOR FOR SWING GATE

ACTUADOR OLEODINAMICO PARA CANCELAS ABATIBLES

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

MARK TANK E

270 - 390

EnglishEnglish

EspanolEspanol

MANUAL DE INSTALACIÓN

y informaciones de seguridad

INSTALLATION MANUAL

and Security Information

67410019

FEATURES AND SPECIFICATIONS

The MARK TANK E 270 and MARK TANK E 390 are two high quality hydraulic operators for residential and condominium use with

leaf length up to respectively 3 and 5 m.

Available in the following versions:

SC (with lock only in closing)

SB (without lock)

SA (with lock only in opening)

AC (with lock in opening and closing)

The lock is guarantied on leaves with lengths under 1,80 m with the MarkTank E 270 operator while for lengths up to 2.20 m use the

Mark Tank E 390. An electric lock should be used for leaves (in all versions) exceeding those lengths.

The Mark Tank E is supplied with by-pass valves for the power regulation in both opening and closing. Electronic adjustable slow

down in opening and closing with electronic control board. For the European laws and directives actually in force it is strongly

recommended to use the Safety Gate (device for the reading of the gate position), for reverse in case of obstacle.

CICLES/HOUR

OPERATORS

MARK TANK E 270

MARK TANK E 390

3 m

5 m

MARK

TANK E 270

MARK

TANK E 390

TECHNICAL FEATURES

Rod speed

Operating temperatures

Thermal protection

Power supply

Power

Absorbed current

Stroke

Cycles hour (at a temp. of 20°C)

Max working pressure

ax Thrust

Capacitor

Weight

rotection class

Max leaf lenght

Opening degree of the leaf

Dimensions (mm)

Max. leaf length

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

Fig. 1

/ 390

270

90 09 / 123

10 / 129050

Fig. 2

21. Shaft cover

2. release

3. Front bracket

4. Rear bracket

5. Cylinder

6. By-pass valves

7. Electric motor

8. Hydraulic pump

9. Exit electric cables

MARK TANK E 270 MARK TANK E 390

230 V (±5%) 50/60 Hz

180 W 220 W

1 A

270 mm

1,2 cm/s

40 50

30 bar 40 bar

-40°C +60°C

130°C

250 daN 640da N

12,5µF

10,5 kg 12 kg

Ip55

3 m 5 m

90° - 110°

Note: The frequency of use is valid only for the first hour at 20°C room

temperature.

MARK TANK E

EnglishEnglish

USING GRAPHIC

OPERATOR MARK TANK E

REV 00 - 07/201367410019

Rear attachment

Pin rear

attachment

(short) Oil fill in cover

Brass Pin (long)

Breather screw

Release key

Plastic frame,

anti-vibration (big)

Plastic frame,

anti-vibration (small)

Valve cover

Front bracket Shaft Cover

End cover

By-pass valves

adjustment key

(only for installer)

OPTIONAL

Shaft

Fig. 3

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

Clevis Attachment

EnglishEnglish

REV 00 - 07/2013 3

67410019

MARK TANK E

TYPICAL INSTALLATION

INSIDE

Fig. 4 Fig. 5

TYPE OF INSTALLATION

It is possible to install the Mark Tank E with opening inside (Fig.4) or opening outside (Fig.5).

Install the operator always

inside the property

inside inside

Outside

OUTSIDE

Inward installation Outward installation

1. MARK TANK E operator

2. Mechanical stop

3. Control board

4. Warning lamp

5. Photocell tx

6. Differential switch 16A-0,03A

7. Photocell rx

8. Key switch start-stop

9. Antenna

10. Column for photocells

11. Warning notice

12. Safety Gate

1010

1212

2x1,5

2x1

3x1 SCH.

3 1 Hx SC .

3x1,5

2x1

58RG

3x1,5

2x1

3x1

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

EnglishEnglish

REV 00 - 07/2013

467410019

MARK TANK E

Inside

outside

INWARD INSTALLATION

Total stroke 270 mm - max suggested stroke 250 mm

a b d

max Max

Opening

Angle

(mm) (mm) (mm)

250 215

250

215

249 225

250 235

255 240

249 240

248

247

100

105

120

125

140

145

150

155

160

170

180

115

150

110

145

105

130

125

110

105

100

105

110

120

130

110°

90°

110°

90°

105°

90°

100°

90°

100°

90°

95°

90°

250

246

Max stroke

(mm)

Stroke

for 90°(mm)

Fig. 6

To obtain 110° with d > 55 mm make a recess in the gate.

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

a b d

max

(mm) (mm) (mm)

368 295

372 300

372

370

310

370 330

370

371

355

370

360

365

369

370

125

130

140

145

160

175

185

195

240

250

260

270

280

295

170

235

165

230

210

195

145

190

140

175

110

125

105

115

100

110

120

130

140

185

195

205

215

230

245

125°

90°

120°

90°

110°

90°

110°

90°

100°

90°

95°

90°

95°

90°

370

369

Total stroke 390 mm - max. recommended stroke 370 mm

Max

Opening

Angle

Max stroke

(mm)

Stroke

for 90°(mm)

Inside

outside

INWARD INSTALLATION

Fig. 6 bis

To obtain 110° with d > 55 mm make a recess in the gate.

EnglishEnglish

REV 00 - 07/2013 5

67410019

MARK TANK E

a b

(mm) (mm)

356 342

345 336

330

335

319

250

255

265

270

275

100

100°

95°

90°

325

342

Total stroke 390 mm - max. recommended stroke 370 mm

Max

Opening

Angle

Max stroke

(mm)

Stroke

for 90°(mm)

Total stroke 270 mm - max suggested stroke 250 mm

a b Max

Opening

Angle

(mm) (mm)

250 240

250

243

241

150

160

165

175

180

95°

90°

95°

90°

250

249

Max stroke

(mm)

Stroke

for 90°(mm)

inside

outside

OUTWARD INSTALLATION

Fig. 7

inside

outside

OUTWARD INSTALLATION

Fig. 7 bis

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

EnglishEnglish

REV 00 - 07/2013

667410019

MARK TANK E

PRELIMINARY

- Open carefully the package, making sure

not to loose parts which are listed in fig. 3

- Attach the rear oscillating bracket as

shown in fig. 9

Attention: Do not use a hammer for the

insertion of the short brass pin; its fitting

into the bracket and clevis attachment must be

done by the simple pressure of the hands.

Attention: Do not incline the hydraulic

operator further than the allowed angle of the

oscillating bracket (1), risks the possible

braking of it.

INSTALLATION OF THE OSCILLATING REAR BRACKET

Fig. 9

Adjustable rear bracket (with screws)

(Accessory on demand)

INSTALLATION OF REAR

BRACKET

According to the type of opening that you have chosen

(inside or outside) and to the chosen leaf rotation (see

page 5-6), the rear bracket must first be cut respecting the

quote “a” on page 5-6 and then welded as in fig. 10.

The support must be positioned so that the operator is

perfectly levelled (Fig. 10, Fig. 12)

Fig. 10

Fig. 11

(1)

98 mm

55 mm

m65 m

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

Fig. 8

m5 8 m

EnglishEnglish

REV 00 - 07/201367410019

MARK TANK E

POSITIONING OF THE FRONT BRACKET

Once the operator is attached to the post and the leaf set in the closed position execute the following

operations:

1. Release the operator (as in fig. 25)

2. Pull-out completely the chromate shaft and push it back in 1cm

3. Attach the shaft to the front bracket (Fig. 13)

4. Set the operator perfectly levelled and mark the position of the front bracket (Fig.12)

Attention: avoid the welding of the front bracket to the shaft of the hydraulic operator already attached;

the welding scraps (daps) could ruin the chromium plating of the shaft.

Fig. 13

Fig. 12

Front bracket weldedFront bracket screwed

Fig. 14 Fig. 15

70 mm 70 mm

3,5 m

46 mm

WELDING OF THE FRONT BRACKET TO THE GATE

The front bracket must be positioned so that the operator is perfectly levelled

According to the nature of the gate the front bracket (wood, steal, Aluminium) can be:

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

EnglishEnglish

REV 00 - 07/201367410019

MARK TANK E

BREATHER SCREW

ATTENTION

It is obligatory to remove the breather

screw at the end of the installation.

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

Unscrew and remove

the screw under the

operator at the end

of installation

Fig. 16

Fig. 17

EnglishEnglish

REV 00 - 07/2013

TORQUE ADJUSTMENT (by pass valves)

Adjust the opening and closing forces of the gate so that the diagram of the force is respected (present in the regulation

EN 12453);Anyway the max. thrust force should never be superior of 15 KgF.

Down

Grey

Yellow

Fig. 18

Fig. 19

Fig. 20

Grey

Yellow

Acting on the by-pas

valves, it is possible to

adjust the operator

pressure in the opening

and closing process.

By-Pass Valves

67410019

MARK TANK E

INSTALLATION OF THE CHROME PLATED SHAFT COVER

Fig. 21

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

EnglishEnglish

REV 00 - 07/2013

OIL LEVEL MEASUREMENT

8,5

Insertion into

the motor (cm)

Fig. 22

3,5

4,5

67410019

MARK TANK E

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Abridor de puerta de SEA

SEA

SEA TORG Series Manual de instrucciones

SEA

SEA ERG Guía del usuario

SEA

SEA SCUTI Manual de usuario

SEA

SEA SATURN Manual de usuario

SEA

SEA SURF 350 Reversible Manual de usuario

SEA

SEA ALPHA 200 STANDARD Manual de usuario

SEA

SEA JOINT Instrucciones originales

SEA

SEA COMPACT 200 CP Manual de instrucciones

SEA

SEA GATE 2 DG INVERTER Manual de usuario

SEA

SEA FLIPPER Manual de usuario

SEA

SEA KITE Manual de usuario

SEA

SEA full tank Manual de usuario

SEA

SEA FULL TANK 100 Manual de usuario

SEA

SEA LYRA Manual de usuario

SEA

SEA SUPER FULL TANK Series Instrucciones originales

SEA

SEA ARM Manual de instrucciones

SEA

SEA ALPHA 330 STANDARD Instrucciones originales

SEA

SEA Libra Mini Tank Instrucciones originales

SEA

SEA COUGAR 270 Manual de usuario

SEA

SEA SURF Series Manual de usuario

SEA

SEA GER Manual de instrucciones

SEA

SEA TAURUS BOX 1000 Manual de usuario

SEA

SEA LYRA Manual de instrucciones

SEA

SEA Libra Mini Tank Manual de usuario

Manuales populares de Abridor de puerta de otras marcas

Elite

Elite CSW200UL Manual de usuario

CAME

CAME FROG-PM4 Manual de usuario

SOMFY

SOMFY FX230 Manual de usuario

Aprimatic

Aprimatic ONDA 500 Manual de usuario

Turnstiles

Turnstiles FSW 900 Manual de usuario

Erreka

Erreka BUL BL33 Instrucciones de funcionamiento

Erreka

Erreka VULCAN S Manual de usuario

Beninca

Beninca R1-2 WBV Manual de usuario

Erreka

Erreka VULCAN D Manual de usuario

Motorline professional

Motorline professional FORT Manual de instrucciones

Beninca

Beninca BOB5024 Manual de usuario

AGA

AGA GATEMASTER 900 HD Manual de usuario

Chamberlain

Chamberlain MotorLift HC280ML Manual de usuario

SOMFY

SOMFY Dexxo RTS Pro Manual de usuario

Cardin

Cardin BL Series Manual de usuario

Westfalia

Westfalia 85 27 06 Manual de usuario

CAME

CAME F500 Manual de usuario

Extel

Extel VERA Manual de usuario