Sea gull lighting 1535-01 Manual de usuario
Copyright 1998, Sea Gull Lighting Products, Inc.
REA AN SAVE THESE INSTRUCTIONS
Total fan
weight
1535-01 1535-02
1535-07 1535-09
1535-15 1535-26
1535-61 1535-83
1535-85 1535-713 1535-962
Ceiling Fan Installation Instructions
For item numbers:
CELEBRITY ELUXE
52" indoor fans
HC-339
®
Copyright 1998, Sea Gull Lighting Products, Inc.
123
TOOLS REQU RED
Phillips Screwdriver Wire Cutters Pliers Step Ladder
Unpack and inspect fan carefully to be
certain all contents are included. (See
exploded view parts list.)
Turn off power at breaker box to avoid
possible electrical shock.
Use outlet box suitable for fan support.
Secure outlet box directly to the building
structure using ceiling joist screws.
Outlet box must support 35 lbs.
4Install mounting bracket to outlet box
in ceiling using the screws provided
with the outlet box and washers. 5
Feed motor lead wires through downrod/
canopy assembly and insert downrod
into motor yoke. Next, insert clevis pin
through yoke and downrod and secure
with cotter pin. (see inset) Tighten both
yoke set screws to further secure
downrod. 6
Carefully lift fan assembly onto mounting
bracket. Rotate fan so that the notch on
the ball engages the ridge in the
mounting bracket. This will allow hands-
free wiring.
Clevis
Pin Set
Screws
Cotter
Pin
Ridge Ball Notch
Safety Tips
WARNING: TO RE UCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOW-
ING:
REA AN SAVE THESE INSTRUCTIONS
INSTALLATION
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards(ANSI/
NFPA 70-1996), including fire-rated construction.
Use this unit only in the manner intended by the manufacurer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding
conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.
Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7
feet from the floor to the trailing edge of the blade.
To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support.
(Mounting must support at least 35 lbs.)
o not bend blade holders during installation to motor, balancing or during cleaning. o not insert foreign object between rotating
blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
NEVER place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the
heating equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association
(NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such
as a tag, to the service panel.
Copyright 1998, Sea Gull Lighting Products, Inc.
3
2While the fan assembly is still on the
ground thread the safety cable through
the mounting bracket.
safety cable
mounting
bracket
Lift fan assembly and install the safety cable
directly to the building structure using the 3" lag
screw and plain washer provided. Before
proceeding to the next step make sure that the
cable is properly installed and will support
the fan weight. Make sure the screw
washer and safety cable are installed using
the order pictured above.
4
Ball
Notch
A
5
Install mounting bracket to outlet box in
ceiling using the screws provided with the
outlet box and washers.
1
Feed motor lead wires through downrod/
canopy assembly and insert downrod into
motor yoke. Next, insert clevis pin through
yoke and downrod and secure with cotter
pin. (see inset) Tighten both yoke set
screws to further secure downrod.
Clevis
Pin Set
Screws
Cotter
Pin
Ridge
plain
washer
safety cable
3" lag
screw
Set
screw
WARNING: MOUNT ONLY TO AN OUTLET OX MARKED
ACCEPTA LE FOR FAN SUPPORT
All set screws must be checked and retightened where necessary before
installation.
Canadian Safety Tips
A. Carefully lift fan assembly onto mounting
bracket. Rotate fan so that the notch on
the ball engages the ridge in the
mounting bracket. This will allow hands-
free wiring. For wiring instructions please
refer to page 4 step #7.
Canadian Mounting System Insert
Copyright 1998, Sea Gull Lighting Products, Inc.
Note:
After installation, please refer to operation, maintenance and troubleshooting sections in this manual.
If your fan is packaged with a light kit or if you wish to install a separately purchased light kit,
please refer to the insert sheet titled: L
IGHT
K
IT
I
NSTALLATION
INSTALLATION
WIRING OPTION WITH WALL SPEE CONTROL
Wall
control
Light Switch
Fan Switch
8
For control of fan and optional light from wall
location, follow diagram above. NOTE: A
professional electrician is recommended
for this type of installation.
7
*ATTACH BLUE WIRE
ONLY IF ATTACHING
LIGHT KIT WITH FAN
*
Secure with
twist-lock wire
connectors
(included)
For pullchain controls, follow diagram above.
Make sure that all exposed wiring is secured
inside wire nuts. Note: Wires from house may
vary in color and may not include ground wire.
After wiring is conplete, gently push
wires into junction box with wire nuts
pointing upward. Refer to point 3 of
safety tips.
STAN AR WIRING OPTION
9
Raise the canopy up and align the two
holes in the canopy with the two holes in
the hanger bracket. Secure with two 5/
32 x 1/2" screws provided.
COMBO-BLA E
10
Combo-Blades feature two high quality
finishes on one blade. Select the one
that best complements your decor, or
change the style with just a flip of the
blade. 11
Fabric
Washers
Attach blade brackets to blades
using the blade bracket screws and
washers provided.
12 13
Check the motor for plastic shipping stabilizer
tabs, and remove them if they are
present. Attach blade assembly to motor
using the motor screws and washers
provided. Tighten screws securely.
Shipping
Stabilizer
Tab
14 After attaching blade; reinstall the
switch housing using the three screws
previously removed.
To gain access to the blade bracket
attachment holes remove the switch
housing cover by unscrewing the three
screws. Gently slide the cover off .
Copyright 1998, Sea Gull Lighting Products, Inc.
TROUBLESHOOTING GUI E
SUGGESTED REMEDY
TROU LE
1. If fan does not start:
2. If fan sounds noisy:
3. If fan wobbles:
Touching
Ceiling
Figure 1
lade Tip Down:
lade Tip Up:
Fan Blade
Fan Blade
Figure 2
Blade Brackets
4. If light does not work:
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or
wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please
check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installa-
tion, please call our Customer Service Center at the number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, switch power off at service panel and lock service disconnecting means
to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such as a tag, to the service panel.
1. Check main and branch circuit fuses or circuit breakers.
2. Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: Make sure main power is turned off.
3. Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when switch is in the
middle.
4. Make sure that shipping stabilizer tabs have been removed from motor (see installation step #13).
1. Check to make sure all screws in motor housing are snug (not over tightened).
2. Check to make sure the screws which attach the fan blade holder to the motor are tight.
3. Check to make sure wire nut connectors in switch housing are not rattling against each other or against the
interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4. If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glassware are finger tight.
Check to be sure light bulb is tight in socket and not touching glass shade(s). If vibration persists from
glass, remove glass and install a 1/4" wide rubber band on glass neck to act as an insulator. Replace glass
and tighten screws against rubber band.
5. Some fan motors are sensitive to signals from Solid State variable speed controls. O NOT USE a Solid
State variable speed control.
6. Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after this period.
1. Make sure that the ridge of the canopy engages the notch in the downrod ball. (See illustration in Step #6
of ownrod Mount installation).
2. Check that all blades are screwed firmly into blade holders.
3. Check that all blade holders are tightened securely to motor.
4. Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and junction box
is mounted firmly to ceiling joist.
5. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on
the ceiling above the tip of one of the blades. Measure this distance as shown in Figure 1. Keeping measure
within 1/8", rotate the fan until the next blade is positioned for measurement. Repeat for each blade. If all
blade levels are not equal, you can adjust blade levels by the following procedure. To adjust a blade tip
down, insert a washer (not supplied) between the blade and blade holder at the screw closest to the motor
(Figure 2). To adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at the
two screws farthest from the motor (Figure 2).
6. If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the
weight and possibly result in smoother operation.
1. Check blue wire from fan to make sure it is connected to hot wire from house.
2. Check for loose or disconnected wires in fan switch housing.
3. Check for loose or disconnected wires in light kit.
4. Check for faulty light bulbs.
CAUTION: Make sure main power is turned off before entering switch housing.
FOR TECHNICAL SUPPORT CALL:
(866) 449-2821
Copyright 1998, Sea Gull Lighting Products, Inc.
2/6/98 REV.0 NEW ISSUE FOR SEAGULL CELEBRITY STYLE FAN.
Este manual sirve para los siguientes modelos
21
Tabla de contenidos
Otros manuales de Admirador de Sea gull lighting
Sea gull lighting
Sea gull lighting 1575BLE Series Manual de usuario
Sea gull lighting
Sea gull lighting 1525 Series Manual de usuario
Sea gull lighting
Sea gull lighting 15030 series Manual de usuario
Sea gull lighting
Sea gull lighting 1558 Manual de usuario
Sea gull lighting
Sea gull lighting 15070 Series Manual de usuario
Sea gull lighting
Sea gull lighting Long Beach 1540-15 Manual de usuario
Sea gull lighting
Sea gull lighting MAIN STREET Manual del propietario
Sea gull lighting
Sea gull lighting 1590 Series Manual de usuario
