Sculpt AXIS I1000 Manual de operación
1
1. PREFACE
2. SPECIFICATIONS AND CLEARANCES
3. PRELIMINARY INSTALL GUIDE
4. INSTALL GUIDE
5. OPERATION & MAINTENANCE
6. TEST REPORTS
7. WARRANTY
8. FINAL WORDS
I1000 | I1000DS FREESTANDING
INSTALLATION & USER GUIDE
AXIS
NOTICE TO INSTALLER:
These instructions must be left with the owner, who should keep them for future use.
Edition: 26/10/2022
2
COMPLIANCE PLATE AND SERIAL NUMBER.
The instructions in this manual are recommendations only, the distributor and manufacturer bears no liability to the interpretation of these instructions.
Please ensure to download the latest version of this manual from our website: www.sculptreplaces.com.au/installation-manuals/
© Copyright 2021 Sculpt Fireplaces Collection
3
Thank you for choosing Sculpt Fireplaces as your heater of choice.
Your replace is the result of careful design, artisan engineering and safety tests.
If it is properly installed, used and maintained, you may be sure that you will have an outstanding
heating feature in your home for years to come.
We advise you to read through this guide in order to become acquainted with the installation
methods specic to your replace.
It is recommended that this replace be installed by a qualied and licensed trades professional.
You will nd in this guide the answers to most of your questions, should you require further
assistance we recommend you contact your retailer.
Before igniting your replace for the rst time, please carefully read this manual.
Follow @sculptreplacecollection on Instagram, SculptFireplaceCollection on Facebook and be
sure to post your latest masterpiece installed with the hashtag #sculptres.
We hope we’ve helped make you the envy of your friends this winter and for years to come.
From all of us,
Sculpt Fireplace Collection
CONGRATULATIONS!
4
IMPORTANT
Heating capacity of the following appliances are a guide only and refers to areas with 2.4m ceilings
and 6 or more star rated buildings. Heating output may vary depending on factors such as building
characteristics, quality of insulation, type of rewood used and climate zone.
All dimensions shown are approximate. Check all dimensions accurately prior to installation. In line with
our policy of continuous improvement, we reserve the right to alter specications without notice.
All units comply and MUST be installed to Australian & New Zealand Standard AS/NZS 2918:2018.
When in use some parts may become hot. A suitable re guard is recommended where very young,
elderly or inrm are concerned.
ALL FIREPLACES IN THIS MANUAL CONFORM TO AUSTRALIAN AND NEW ZEALAND STANDARDS
AS/NZS 2918:2018 DOMESTIC SOLID FUEL BURNING APPLIANCES & AS/NZS 4012/40132014.
The instructions in this manual are recommendations only, the distributor and manufacturer bears no liability to the interpretation of these instructions.
© Copyright 2021 Sculpt Fireplaces Collection
5
2. SPECIFICATIONS
AXIS I1000 Single Sided
Solid steel rebox with rebricks
Up to 15 to 30 Squares*
1.2g/kg
66%
Secure swing door opening system
4.6m
197mm, 250mm, 200mm
Recommended for well insulated homes
10 year rebrick and 5 year rebox warranty**
180kg
Width: 1220mm Depth: 1055mm Thickness: 9mm
***
Material
Heating Capacity
Avg Emissions
Avg Eciency
Glass Door
Minimum Flue Height
Flue Dimensions
Outside Air Kit
Warranty
Weight
Minimum Hearth Dimensions
* Heating capacity of the following appliances are a guide only and refers to areas with 2.4m ceilings
and 6 or more star rated buildings. Heating output may vary depending on factors such as building
characteristics, quality of insulation, type of rewood used and climate zone.
** See warranty pg. 23 of the manual
*** Refer to pg. 6 for further details about the clearances & hearth
100
58,8
33,5
83
50,65
FRONT SIDE
450mm
1000mm
833mm
340mm
587mm
6
2. SPECIFICATIONS
This appliance and ue were tested at the following clearances.
The Axis I1000 Single sided free standing appliance and 8”ue system with a painted solid casing
between the appliance and ceiling conforming to joint Australian/New Zealand Standards 2918:2001,
Appendix B.
A minimum 1055mm deep X 1220mm wide and 9mm non-combustible hearth should be installed,
see joint AS/NZs 2918:2001 3.3.2). The oor protector (hearth) should extend 550mm in front of the
appliance fuel loading door and be placed centrally in the 1220mm width.
***The appliance must be elevated a minimum of 250mm above the hearth (on a non combustible
surface). If the heater is placed directly onto the hearth, the hearth dimensions required will be greater.
Please refer to AS/NZS 2918:2018 as per the minimum for a non-tested appliance.
Clearances & Hearth- Axis I1000 Single Sided
COMBUSTIBLE WALLS
COMBUSTIBLE WALLS
450MM
250MM
SWING DOOR
APPLIANCE
550MM
HEARTH
1055MM
1220MM
COMBUSTIBLE WALLS
COMBUSTIBLE WALLS
APPLIANCE
150MM 150MM
HEARTH
SWING DOOR
1055MM
1220MM
550MM
POSITION A PARALLEL POSITION
Diagram not to scale
POSITION B CORNER POSITION
Diagram not to scale
7
2. SPECIFICATIONS
AXIS I1000 DS Double Sided
Material
Heating Capacity
Avg Emissions
Avg Eciency
Glass Door
Minimum Flue Height
Flue Dimensions
Outside Air Kit
Warranty
Weight
Minimum Hearth Dimensions
Solid steel rebox with rebricks
Up to 15 to 30 Squares*
1.0g/kg
62%
2X Secure swing door opening systems
4.6m
197mm, 250mm, 300mm
Recommended for well insulated homes
10 year rebrick and 5 year rebox warranty**
180kg
Width:1220mm Depth:1605mm Thickness: 9mm***
100
58,8
33,5
83
50,65
FRONT SIDE
1000mm
588mm
340mm
506mm
830mm
* Heating capacity of the following appliances are a guide only and refers to areas with 2.4m ceilings
and 6 or more star rated buildings. Heating output may vary depending on factors such as building
characteristics, quality of insulation, type of rewood used and climate zone.
** See warranty pg. 23 of the manual
*** Refer to pg. 8 for further details about the clearances & hearth
8
2. SPECIFICATIONS
This appliance and ue were tested at the following clearances:
The Axis I1000 Double Sided free standing appliance and 8”ue system with a solid casing between the
appliance and ceiling conforming to joint Australian/New Zealand Standards 2918:2001, Appendix B.
A minimum 1055mm deep X 1220mm wide and 9mm thick non-combustible hearth should be installed,
see joint AS/NZS 2918:2018 3.3.2). The oor protector (hearth) should extend 550mm in front of the
appliance fuel loading door and be placed centrally in the 1220mm width.
Clearances & Hearth- Axis I1000 DS Double Sided
POSITION A PARALLEL POSITION
Diagram not to scale
***The appliance must be elevated a minimum of 250mm above the hearth (on a non combustible
surface). If the heater is placed directly onto the hearth, the hearth dimensions required will be greater.
Please refer to AS/NZS 2918:2018 as per the minimum for a non-tested appliance.
9
It is the users duty to make themselves aware of and apply all national or more restrictive local
standards and instructions (AS/NZS 2918:2018).
IMPORTANT
Prior to unpacking and installation ensure the appliance has not been damaged during transit. Please
ensure you check the glass, the door(s), the damper operation and the door locking mechanism
Before any work is carried out, as per local and national regulations and laws, this appliance MUST be
installed by a licensed professional as per AS/NZS 2918:2018.
IMPORTANT WARNING
It is strictly forbidden to use any combustible materials (ie: wooden framing, plaster, etc) near or around
this appliance. Any exception from this rule is a health and safety hazard which will result in a non-
compliant installation and a void of warranties.
Electrical cables and components must not be placed in the vicinity of the appliance as it is a re
hazard.
3. PRELIMINARY INSTALL GUIDE
10
For the installation and use of this appliance, the tter and the user should strictly adhere to local and
national regulations in addition to AS/NZS 2918:2018. The installer should comply with the instructions
and recommendations detailed in this manual. Safety and operation of the replace is directly
dependent thereon. The liability of the manufacturer can neither be retained nor assured following
failure of installation or incorrect use which does not comply with AS/NZS 2918:2018.
As each installation is unique, a qualied and licensed trades professional should take all required
preliminary precautions depending on the technical elements inherent to each job.
In-observance of the assembly instructions in conjunction with AS/NZS 2918:2018 entails the liability
of the person who carries it out.
As a result of faulty assembly, irrational use of parts or additional components that were not supplied
by the manufacturer, and/or modifying of the appliance or components will result in inferior or unsafe
operation. Should this occur the manufacturer bears no liability, and will result in a null and void product
warranty.
PRELIMINARY INSTALL INFORMATION
All images and diagrams in this manual are for installation reference purposes only and are not to
scale, the distributor and manufacturer bears no accuracy of these images and accepts no liability. The
purpose of these images and diagrams is to act as a guide in conjunction with the written components,
and are NOT to be used to instruct independently. The order of steps listed in this manual are
recommendation only.
It is strongly recommended that the licensed trade professional who is performing the installation of
this appliance, completely read and comprehend all instructions in this manual prior to proceeding.
Sculpt Fireplaces & Axis reserves the right to change these specications without prior notice.
PLEASE READ PRIOR TO INSTALL
ACCEPTABLE VARIANCE ALLOWANCE
Due to the production of these hand assembled and manufactured replaces, there is an acceptable
allowance of 3-5mm variance of the unit, including the door frame. This variance in production is non-
claimable under any warranties.
HEAT RESISTANT MATERIALS
Heat resistant materials must meet AS/NZS 2918:2018 clause 1.4.27 a material with an allowable
service temperature of 600° Celsius or greater.
3. PRELIMINARY INSTALL GUIDE
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Chimenea de interior de Sculpt
Sculpt
Sculpt Seguin Europa 7 Manual de usuario
Sculpt
Sculpt AXIS 1000 Manual de operación
Sculpt
Sculpt AXIS Manual de operación
Sculpt
Sculpt SEGUIN Aurore Manual de operación
Sculpt
Sculpt JC BORDELET Tatiana 997 Manual de operación
Sculpt
Sculpt SEGUIN MULTIVISION HYDRO 80 Manual de operación
Sculpt
Sculpt AXIS Series Manual de operación
