Screen Technics 1490800 Manual de usuario

Continued Over.../

INSTRUCTIONS - SWING DOWN FLAT PANEL LIFT

Thank you for purchasing a Screen Technics Swing Down Flat Panel

Lift, please ensure that you read the following instructions fully before

attempting to install this product.

NOTE: THIS SWING UTILISES AN ADVANCED FALL ARRESTOR SYSTEM, THE SWING DOWN CAN ONLY BE OPERATED

IN A HORIZONTAL POSITION, IF THE SWING DOWN IS OPERATED ON ITS SIDE OR NOT IN A HORIZONTAL POSITION,

THE ANTI-FALL DEVICE WILL LOCK AND DISCONNECT POWER. IF THE ANTI-FALL DEVICE IS ACTIVATED, IT WILL

REQUIRE REPLACEMENT.

1. CONTROL

• Supplied with a Connect motor controller

• Infra-Red operation

• 2 x Dry Contact close inputs Up/Down

2. 4 CORE WIRING WAGO CONNECTOR

• Pin 1 – Brown Down

• Pin 2 – Black Up

• Pin 3 – Yellow / Green Earth

• Pin 4 – Blue Neutral

3. INSTALLATION EXAMPLES

• Bolted to timber in ceiling, attached to ceiling structure

1. Control.

a. Supplied with a Connect motor controller

b. Infra-Red operation

c. 2 x Dry Contact close inputs Up/Down

2. 4 Core Wiring Wago Connector

a. Pin 1 – Brown Down

b. Pin 2 – Black Up

c. Pin 3 – Yellow / Green Earth

d. Pin 4 – Blue Neutral

3. Installation Examples

a. Bolted to timber in ceiling, attached to ceiling structure

b. Attached to cable or chain to a

suitable structure within ceiling

space, using adjustable shackles

for levelling

1. Control.

a. Supplied with a Connect motor controller

b. Infra-Red operation

c. 2 x Dry Contact close inputs Up/Down

2. 4 Core Wiring Wago Connector

a. Pin 1 – Brown Down

b. Pin 2 – Black Up

c. Pin 3 – Yellow / Green Earth

d. Pin 4 – Blue Neutral

3. Installation Examples

a. Bolted to timber in ceiling, attached to ceiling structure

b. Attached to cable or chain to a

suitable structure within ceiling

space, using adjustable shackles

for levelling

1. Control.

a. Supplied with a Connect motor controller

b. Infra-Red operation

c. 2 x Dry Contact close inputs Up/Down

2. 4 Core Wiring Wago Connector

a. Pin 1 – Brown Down

b. Pin 2 – Black Up

c. Pin 3 – Yellow / Green Earth

d. Pin 4 – Blue Neutral

3. Installation Examples

a. Bolted to timber in ceiling, attached to ceiling structure

b. Attached to cable or chain to a

suitable structure within ceiling

space, using adjustable shackles

for levelling

1. Control.

a. Supplied with a Connect motor controller

b. Infra-Red operation

c. 2 x Dry Contact close inputs Up/Down

2. 4 Core Wiring Wago Connector

a. Pin 1 – Brown Down

b. Pin 2 – Black Up

c. Pin 3 – Yellow / Green Earth

d. Pin 4 – Blue Neutral

3. Installation Examples

a. Bolted to timber in ceiling, attached to ceiling structure

b. Attached to cable or chain to a

suitable structure within ceiling

space, using adjustable shackles

for levelling

c. Utilising 4 angle brackets, and mount using threaded rod

• Attached to cable or chain to a suitable structure within ceiling space, using adjustable

shackles for levelling

info@screentechnics.com.au

screentechnics.com.au

AUSTRALIA

22-24 Suttor Road, Moss Vale NSW 2577

+61 2 4869 2100

NEW ZEALAND

44 Mahana Road, Te Rapa, Hamilton

0800 022 821

ESTABLISHED IN 1990

STEP 4. FITTING DOOR TO SWING DOWN

• The swing down door is packaged separately

• The door bracket is pre-set at the factory at 90 degrees, as shown below

• This will allow the tting or removal of the door. Should the door require removal, the door

must not exceed 90 degrees

• After the door is hung using the hook system

• Fit the 6 side bolts with tube spacers to hold door in place

INSTRUCTIONS - SWING DOWN FLAT PANEL LIFT

c. Utilising 4 angle brackets, and mount using threaded rod

• Utilising 4 angle brackets, and mount using threaded rod

4. Fitting Door to swing down

a. The swing down door is packaged separately

b. The door bracket is pre-set at the factory at 90 degrees, as shown

below

c. This will allow the fitting or removal of the door. Should the door

require removal, the door must not exceed 90 degrees

d. After the door is hung using the hook system

e. Fit the 6 side bolts with tube spacers to hold door in place

Door hook system

with bolts and

spacers shown

Swing Down

Door

4. Fitting Door to swing down

a. The swing down door is packaged separately

b. The door bracket is pre-set at the factory at 90 degrees, as shown

below

c. This will allow the fitting or removal of the door. Should the door

require removal, the door must not exceed 90 degrees

d. After the door is hung using the hook system

e. Fit the 6 side bolts with tube spacers to hold door in place

Door hook system

with bolts and

spacers shown

Swing Down

Door

4. Fitting Door to swing down

a. The swing down door is packaged separately

b. The door bracket is pre-set at the factory at 90 degrees, as shown

below

c. This will allow the fitting or removal of the door. Should the door

require removal, the door must not exceed 90 degrees

d. After the door is hung using the hook system

e. Fit the 6 side bolts with tube spacers to hold door in place

Door hook system

with bolts and

spacers shown

Swing Down

Door

Door hook system with bolts

and spacers shown

Swing Down Door

5. Limit Setting

a. Limit are accessible from slot inside swing down

b. Limit towards the front adjusts top limit / closed - This limit should

not be adjusted as damage to the panel may occur

c. Limit towards the back adjusts the bottom limit / open

Should you have any questions regarding the installation of our products

please call our sales desk on +61 2 4869 2100 for assistance

Screen Technics Pty Ltd

Cnr Vale & Suttor Roads, Moss Vale, NSW 2577

Ph: +61 2 4869 2100

www.screentechnics.com.au

Thinking Lifters ….. Think Screen Technics

STEP 5. LIMIT SETTING

• Limit are accessible from slot inside swing down

• Limit towards the front adjusts top limit / closed - This limit should not be adjusted as damage

to the panel may occur

• Limit towards the back adjusts the bottom limit / open

ALWAYS ALLOW FOR PRODUCT REMOVAL IN ORDER TO BE SERVICED AND MAINTAINED.

Should you have any questions regarding the installation of our products please call our sales

desk on +61 2 4869 2100 for assistance

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de elevación de Screen Technics

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manual de usuario

Manuales populares de Sistema de elevación de otras marcas

morse

morse 82H-124 Manual de usuario

Braun

Braun NL955 Series Manual de usuario

haacon

haacon 1889.10 Manual de usuario

Protekt

Protekt AT 252 Manual de usuario

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manual de usuario

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manual de usuario

Genie

Genie Z-60/34 Manual de usuario

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manual de usuario

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manual de programación

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manual de programación

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manual de programación

BERG

BERG BeNomic EasyLeaf Manual de usuario

Powermate

Powermate LiftGate LG-3 Manual de usuario

Snorkel

Snorkel TM12 Series Manual de usuario

Terberg

Terberg OMNIDEKA Manual de usuario

Harmar Mobility

Harmar Mobility AL625 Instrucciones de funcionamiento

Rotary

Rotary SPO16 Manual de usuario

Ricon

Ricon Mirage F9T Manual de usuario