Schmidt SS 20.600 Manual de usuario

SCHMIDT®Flow Sensor

SS 20.600

Quick Guide

Quick Guide –SCHMIDT®Flow Sensor SS 20.600 Page 2

SCHMIDT®Flow Sensor SS 20.600

Table of Contents

1Important information.......................................................................2

2Application range.............................................................................2

3Assembly.........................................................................................2

4Electrical connection........................................................................2

5Commissioning................................................................................2

6Calculation of volume flow...............................................................2

Imprint:

Version: 536020.02D

Subject to modifications

Quick Guide –SCHMIDT®Flow Sensor SS 20.600 Page 3

1 Important information

This quick guide must be read completely and observed carefully, be-

fore putting the unit into operation.

For detailed information on mounting and operation of the sensor,

a comprehensive manual (535084.02) is available at:

www.schmidt-sensors.com or www.schmidttechnology.de

In case of doubt, please observe the information given there.

Any claims under the manufacturer's liability for damage resulting from

non-observance or non-compliance with these instructions will become

void.

Tampering with the device in any way whatsoever - with the exception

of the designated use and the operations described - will forfeit any

warranty and exclude any liability.

The unit is designed exclusively for the use described below (refer to

chapter 2). In particular, it is not designed for direct or indirect protection

of personal or machinery.

SCHMIDT Technology cannot give any warranty as to its suitability for

a certain purpose and cannot be held liable for accidental or sequential

damage in connection with the delivery, performance or use of this unit.

2 Application range

The SCHMIDT®Flow Sensor SS 20.600 is designed for stationary meas-

urement of flow velocity as well as the temperature of air and gases.

The sensor measures the normal velocity wN(unit: m/s), based on normal

conditions of 1013.25 hPa and 20 °C. The output signal is linear and in-

dependent from pressure and temperature of the medium to be measured.

When using the sensor outdoors, it must be protected against di-

rect exposure to the weather.

When using the sensor in ATEX areas the Supplementary in-

structions for use in explosive atmosphere ATEX (535689.02)

must be read and observed carefully.

Information and safety instructions for the use in media having an

oxygen percentage of > 21 % can be found in the general Instruc-

tions for Use (535084.02).

Quick Guide –SCHMIDT®Flow Sensor SS 20.600 Page 4

3 Assembly

Position the sensor head always at the most advantageous posi-

tion for flow measurement, typically in the middle of the pipe.

The sensor measures unidirectional, the axial tilting of the sensor

head relative to flow direction should not exceed ±3°

The sensor should preferably be installed in hor-

izontal pipes.

Installation in a vertical pipe with downward flow

should be avoided, as the lower measuring range

limit will be increased.

In case of a downward flow at 16 bar overpres-

sure, correct measurement values will be given at

a flow velocity above 2 m/s.

Correct measurements require a flow low in turbulence.

This can be achieved by providing sufficiently long and straight distances

without flow disturbing structures in front of and behind the sensor.

The minimum run-in (L1) and run-out (L2) distances are defined by the

type of the flow obstacle upstream of the measuring position and the

inner pipe diameter D.

Flow obstacle upstream of measuring distance

Minimum distance length of

Run-in (L1)

Run-out (L2)

Light bend (< 90°)

10 x D

5 x D

Reduction / expansion / 90° bend or T-junction

15 x D

5 x D

Two 90° bends in one plane (2-dimensional)

20 x D

5 x D

Two 90° bends (3-dimensional change in direction)

35 x D

5 x D

Shut-off valve

45 x D

5 x D

wN < 2 m/s

Flow

Quick Guide –SCHMIDT®Flow Sensor SS 20.600 Page 5

Installation

The sensor may only be mounted and dismounted when no pres-

sure is applied.

Quick Guide –SCHMIDT®Flow Sensor SS 20.600 Page 6

In case of mechanical strain (e.g. vibration), the nut of the com-

pression fitting must be secured additionally (e.g. a screw lock).

The alignment surface of the sensor’s enclosure must not be used

for countering.

Before pressurisation, the pressure-tight assembly as well as the

correct fastening of the compression fitting and the discarding

protection must be checked.

This check must be repeated periodically.

If the sensor head is immersed in water and operated under pres-

sure, the sensor may be damaged irreversibly.

The sensor measures unidirectional, the axial tilting of its head

relative to flow direction should not exceed ±3°.

4 Electrical connection

Make sure that no operating voltage is active during electrical in-

stallation and that the operating voltage cannot be switched on

inadvertently.

View on plug-in connector of sensor

To operate the sensor a supply voltage of 24 VDC ± 20 % with a

minimum current1of 200 mA is required.

The appropriate protection class III (SELV) respective PELV (ac-

cording EN 50178) has to be considered.

The specified wire colors are valid when one of the SCHMIDT®connect-

ing cables is used.

Without signal current of pulse output 2 (relay).

8 7

A / V

0 ... 100 Hz

Pulse/m³

 100 mA

A / V4 ... 20 mA

0 ... 10 V

0 ... 100 Hz

Pulse/m³

RD  30 VDC

 21 VAC

 50 mA

24 VDC

±20 %

TMwN

AGND

GND

Quick Guide –SCHMIDT®Flow Sensor SS 20.600 Page 7

Name

Function

Wire colour

Pulse 1

Output signal: Flow velocity / volume (digital: PNP)2

White (WH)

Operating voltage: 24 VDC ± 20 %

Brown (BN)

Analog TM

Output signal: Temperature of medium (Auto-U/I)

Green (GN)

Analog wN

Output signal: Flow velocity (analog: Auto-U/I)

Yellow (YE)

AGND

Reference potential for analog outputs

Gray (GY)

Pulse 2

Output signal: Flow velocity / volume (digital: Relay)3

Pink (PK)

GND

Operating voltage: Ground

Blue (BU)

Pulse 2

Output signal: Flow velocity / volume (digital: Relay)3

Red (RD)

Table 1

Typically, AGND has to be selected as measuring reference potential for

the signal output to avoid problems with mass offset.

Depending on the value of the connected load resistance RL, each analog

output switches between operation as voltage interface “U” (0 …10 V) or

current interface “I” (4 …20 mA) automatically (“Auto-U/I”).

The switching threshold is set by a load resistance of RL= 500 … 550 Ω

(hysterisis = 50 ), the maximum load capacity is 10 nF.

For voltage mode, a load resistance of at least 10 kΩis recommended.

5 Commissioning

The valid measuring ranges and the configuration of the signal outputs are

specified on the rating plate.

After applying the supply voltage, the sensor signals the initialization of

the measuring operation by means of all four LEDs (sequence: red, or-

ange, green). The flow output signal will at first adopt a higher value and

then settle to the correct measurement value after about 10 seconds.

LEDs flashing in red indicate an error. For detailed error description,

please refer to the general Instructions for Use (535084.02, page 25).

6 Calculation of volume flow

SCHMIDT Technology provides a "flow calculator" on its homepage for

the calculation of flow velocity or volume flow in (circular) pipes or (rectan-

gular) shafts for the different sensor types:

www.schmidt-sensors.com or www.schmidttechnology.de

Highside driver (galvanically not isolatied; current limited to 100 mA; load to GND)

Galvanically decoupled (max. 30 VDC / 21 VAC / 50 mA)

Quick Guide –SCHMIDT®Flow Sensor SS 20.600 Page 8

SCHMIDT Technology GmbH

Feldbergstrasse 1

78112 St. Georgen

Germany

Phone +49 (0)7724 / 899-0

Fax +49 (0)7724 / 899-101

Email sensors@schmidttechnology.de

URL www.schmidt-sensors.com

www.schmidttechnology.de

Otros manuales para SS 20.600

Tabla de contenidos

Otros manuales de Accesorios de Schmidt

Schmidt

Schmidt SS 20.600 Manual de usuario

Schmidt

Schmidt SS 20.501 Manual de usuario

Schmidt

Schmidt SS 23.400 ATEX 3 Manual de usuario

Schmidt

Schmidt SS 20.700 Manual de usuario

Schmidt

Schmidt SS 20.651 Manual de usuario

Schmidt

Schmidt SS 20.60 Manual de usuario

Schmidt

Schmidt SS 20.700 Manual de usuario

Schmidt

Schmidt SS 20.515 LED Manual de usuario

Schmidt

Schmidt SS 23.700 Ex Manual de usuario

Schmidt

Schmidt SS 20.225 Manual de usuario

Schmidt

Schmidt SS 20.260 Manual de usuario

Schmidt

Schmidt SS 20.600 Ex Diagrama de cableado

Schmidt

Schmidt SS 20.500 Ex Manual de usuario

Schmidt

Schmidt SS 20.600 Manual de usuario

Schmidt

Schmidt SS 20.500 Manual de usuario

Schmidt

Schmidt SS 20.260 Manual de usuario

Schmidt

Schmidt SS 20.261 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario