Saxby Lighting Sight Plus Manual
Instruction leaflet
Sight Plus LED Wall Light
75147
Live Voltages may be present in this unit even when turned of or when completely disconnected.
For your safety, always switch off the supply before changing lightbulbs, or cleaning.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Safety information
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
Recycling advice
This bulb is protected by a shade. This part must be replaced immediately should the shade become
cracked or damaged. This fitting must not be used without the shade in place.
Replace Cracked
Shade
05/07/2021
UK Manufacturer:
BH17 7BY
EU Manufacturer:
1 Gnarrenburg, 27442
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before
commencing any work.
This unit must be fitted by a competent and qualified
electrician.
Install in accordance with IEE Wiring regulations and
current Building Regulations.
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting. Ensure other
persons cannot restore the electrical supply without your
knowledge.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the
connections.
This product is not suitable for dimming.
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling
advice.
These products should not be fitted to PIR circuits or short
duration timed switches.
Sight Plus recessed accessory 72638 and wedge
accessory 72639 are available to purchase separately for
this product.
Specification
Layout
• The mains supply cable must have a minimum cross
sectional area of 1.0mm²
• This product can be ceiling or wall mounted.
• This product has special protection against the ingress
of moisture and is IP65 rated.
Existing fittings must be completely removed before
installation of a new product. Before removing the existing
fitting, carefully note the position of each set of wires.
• Undo the two screws at the end of the unit. Remove the
screws and cover and set aside.
• This unit can be mounted on the wall or ceiling.
• Unclip the front panel by pushing the quick release tabs
to expose back casing.
• Drill out selected knock out and cable entry holes on
the back casing of the product.
• Using the unit as a template mark the position of
the fixing holes. Take care to avoid damaging any
concealed wiring and pipes. The correct fixings should
be used, depending upon the surface to be mounted.
• Pull the cable through the cable entry hole and seal to
maintain the IP rating, and wire as detailed below.
Installation
Wiring
Check that...
• You have correctly identified the wires
• The connections are tight
• No loose strands have been left out of the connection
block.
Voltage: 240V ~ 50Hz
Lamp: 2W LED Module (SMD 2835) - 136lm
IP rating: 65
Duration: 3 hours (180 minutes)
Operating Temperature : -5˚C to 50˚C
Maximum Operating Humidity : 10-90%
Change over Time: Approximately 1s
Battery Specification: 3.6V 900mAh Ni-Cad
Battery Charge Time: 24 hours
Maintained Wiring
Having correctly identified the wiring from your existing light fitting, pull the wire through the hole and connect to the
connection block inside the product in the following way:
PERMANENT TO BATTERY
TO DRIVER
INSERT CABLE
PUSH DOWN
Cleaning Information
• We recommend cleaning with a soft dry cloth or wash
with warm water or just use a damp cloth.
• Do not use abrasive materials as these will damage the
finish.
• Reclip the front panel in place and resecure the diffuser
using the screws. Ensure that the seal is correctly fitted.
• Replace fuse or circuit breaker and switch on. Your light
is now ready for use.
Commissioning
• This unit works in maintained mode. The light will remain
lit all the time and in the event of a power failure will
remain on. The unit will charge automatically.
• remove the link from between the terminals marked
"SW" and connect cables to and from switch.
• Replace fuse or circuit breaker and switch on. Ensure
that the source is mains (240V ~ 50Hz).
• Verify that the LED is illuminated; this confirms that the
batteries are charging.
• Charge the battery for at least 24 hours before first use.
• If the LED is not illuminated then there may be no a.c.
supply, the battery has not been connected properly or
the internal circuit may have failed.
• The battery should be re-charged and checked every
three months.
• The battery should be discharged and the duration of the
lamp in emergency mode checked every six months.
Operation
• If after routine operation check, the lamp does not remain
lit for the three hour period, a new battery pack may be
required.
• Switch off the electricity at the mains, allow batteries to
fully discharge then reconnect to supply and allow to
charge for 24 hours.
• Test again for two hours, if light does not remain lit
change the battery pack as follows:
• Undo the two screws holding the front diffuser in place.
Remove the diffuser and set aside.
• Undo the clips holding the gear tray and fold down.
• Unplug the battery lead from the lead coming from the
PCB. Remove any cable ties around the cables.
• Remove the battery pack. Waste electrical products
should not be disposed of with household waste. Please
recycle where facilities exist. Check with your local
authority or retailer for recycling advice.
• Replace the battery with a 3.6V 900mAh Ni-Cd
ONLY. Use of a different type of battery will damage the
product.
• Write current date on the new battery pack.
• Fit the new battery pack in position and re secure using
the screws set aside earlier. Refit the cable ties in
position and then plug battery pack into the PCB.
• Reclip the gear tray back in position, taking care not to
trap any wires.
• Perform full operation check and update test record.
• Refit the diffuser. Ensure that the seal is correctly
located. Tighten the screws carefully to avoid damaging
the threads.
• Restore power and allow to charge for 24 hours.
Battery Replacement
• The LED Modules in these product are non-replaceable.
Fitting/replacing bulbs
Este manual sirve para los siguientes modelos
1
Otros manuales de Equipo de iluminación de Saxby Lighting
Saxby Lighting
Saxby Lighting Odyssey Spike Manual de usuario
Saxby Lighting
Saxby Lighting Tango Manual de usuario
Saxby Lighting
Saxby Lighting Flexline 73670 Manual
Saxby Lighting
Saxby Lighting Sight Twin Spot Manual
Saxby Lighting
Saxby Lighting Kios 2 Manual de usuario
Saxby Lighting
Saxby Lighting SIGHTPRO 108087 Manual de usuario
Saxby Lighting
Saxby Lighting Axial Rectangular Manual de usuario
Saxby Lighting
Saxby Lighting 13889 Manual de usuario
Saxby Lighting
Saxby Lighting 10430 Manual
Saxby Lighting
Saxby Lighting Sight Plus Manual de usuario
Saxby Lighting
Saxby Lighting OrionSMART Manual de usuario
Saxby Lighting
Saxby Lighting 14008 Manual de usuario
Saxby Lighting
Saxby Lighting 46393 Manual
Saxby Lighting
Saxby Lighting E27 LED GLS Manual
Saxby Lighting
Saxby Lighting 79192 Manual de usuario
Saxby Lighting
Saxby Lighting OrionPRO LED IP20 Manual de usuario
Saxby Lighting
Saxby Lighting Varone 55702 Manual
Saxby Lighting
Saxby Lighting 108750 Manual de usuario
Saxby Lighting
Saxby Lighting Picco Manual de usuario
Saxby Lighting
Saxby Lighting 13929 Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
