Savin 2555 Manual de usuario

Savin 2555

Operating Instructions

COPY REFERENCE

Read this manual carefully before you use this product and keep it handy for future

reference.

For safety, please follow the instructions in this manual.

2. Copying

Basic Procedure

AMake sure that the machine is in Copy mode.

If the machine is not in Copy mode, press the {

Copy/New Job

}key.

BWhen the machine is set for the user code, enter the user code with the

number keys and then press the {

}key.

Reference

⇒P.90 “User Codes”.

CMake sure that there are no previous settings remaining.

Note

❒To clear settings, press the {

Clear Modes/Energy Saver

}key.

DSet your originals.

Reference

⇒P.31 “Setting Originals”.

ESet your desired settings.

FEnter the number of copies required with the number keys.

Sample Copy

Clear/Stop

Start

Enter

TSPS020N

Copying

Note

❒The maximum copy quantity can be set between 1 and 999 (default: 999).

See “Maximum Copy Quantity” in ⇒P.313 “General Features 2/3”.

❒To change the number entered, press the {

Clear/Stop

}key and enter the

new number.

GPress the {

Start

}key.

The machine starts copying.

Note

❒When you set originals on the exposure glass, press the {

}key after all

originals are scanned.

❒Usually, when you set a single original on the exposure glass or in the doc-

ument feeder, the copied paper is delivered face up. However, with some

functions, copies will be delivered face down.

❒You can choose to have copies delivered either face up or face down (ex-

cept for copying through the bypass tray). See “Face-Up/Down Selection

in Platen Mode” in ⇒P.329 “Input/Output”.

❒To stop the machine during the multi-copy run, press the {

Clear/Stop

}key.

❒To return the machine to the initial condition after copying, press the {

Clear

Modes/Energy Saver

}key.

-Auto Reset

The machine returns to its initial condition automatically when your job is fin-

ished, after a certain period of time. This function is called “Auto Reset”.

Note

❒You can change the Auto Reset time. See “Auto Reset Timer” in ⇒P.310

“General Features 1/3”.

-Auto Off

The machine turns itself off automatically after your job is finished, after a cer-

tain period of time. This function is called “Auto Off”.

Note

❒You can change the Auto Off time. See “Auto Off Timer” in the System Set-

tings manual.

Setting Originals

Limitation

❒Set originals after correction fluid and ink has completely dried. Not taking

this precaution could mark the exposure glass and cause marks to be copied.

Note

❒Basically originals should be aligned to the rear left corner. However, some

copy functions may produce different results depending on the direction of

the originals. For details, see the explanations of each function.

Reference

⇒P.19 “Originals”.

Setting Originals on the Exposure Glass

ALift the document feeder.

Important

❒Do not open the document feeder with a force. Otherwise, the cover of the

document feeder might open or be damaged.

Note

❒Be sure to open the document feeder by more than 30°. Otherwise the orig-

inal size might not be detected correctly.

Copying

BSet the original face down on the exposure glass. The original should be

aligned to the rear left corner.

1: Reference mark

2: Scale

Note

❒Start with the first page to be copied.

CLower the document feeder.

Setting Originals in the Document Feeder

Note

❒The last page should be on the bottom.

❒Do not stack originals beyond the limit mark on the side fence of the docu-

ment feeder.

❒When copying thin originals (40 – 52g/m2, 11 – 14 lb. Bond), set one original

in the document feeder at a time or place it on the exposure glass to avoid

damage due to a multi-sheet feed (several pages fed together at the same

time).

❒The original might become dirty if it is written with a pencil or similar tools.

❒Usually, one-sided originals are delivered to the ADF external tray, and two-

sided originals to the ADF tray.

Reference

Regarding originals that the document feeder can handle, see ⇒P.19 “Origi-

nals”.

ND1C01EE

Setting Originals

ASet the aligned originals face up into the document feeder.

Setting a stack of originals is completed when the bottom plate rises.

Important

❒After the bottom plate of the document feeder rises, do not add or force in

originals.

Note

❒Straighten curls in the originals before setting them in the document feed-

er.

❒To avoid a multi-sheet feed, shuffle the originals before setting them in the

document feeder.

❒You can set the timing for the bottom plate of the document feeder to rise.

See “ARDF Original Table Rise Time” in ⇒P.329 “Input/Output”.

Original Orientation

You can set the original orientation separately in the following ways.

This function is useful for copying torn originals or large originals.

❖

Standard Orientation

Select this function when the original direction is the same as the copy paper

direction.

❖

Turn

This function rotates the copy image by 90°.

Use this function when you want to copy onto A3, B4, 11" ×17" paper.

APress the [

Special Original

]key.

TSPH040E

Copying

BSelect the original orientation.

Standard Orientation

AMake sure that the [

Standard Orientation

]key is selected.

90°Turn

When you want to copy A3K, B4Kor 11" ×17"Ksize originals, set your

original in the landscape orientation and then press the [

Turn

]key. The

machine rotates the original image and you can make copies as you wish. This

is useful for copying large originals with the Staple, Punch, Duplex, Combine

or Stamp functions.

For example, if you want to copy A3Kor 11" ×17"Koriginals with for the

Staple function configured as shown below:

Setting Originals

Note

❒It is recommended to use this function together with the Auto Paper Select

or Preset Reduce/Enlarge function.

APress the [

Turn

]key.

CPress the [

]key.

GCGSET2E

Copying

Setting Special Originals

Use this function when you want to use Batch (SADF), Mixed Sizes, Thin mode,

or when you select the original orientation.

Batch (SADF) mode

Up to 100 standard originals can be set in the document feeder at a time. If there

are more than 100 originals, set Batch (SADF) mode so that originals can be fed

automatically without pressing the {

Start

}key each time they are set in the doc-

ument feeder.

Important

❒When setting special originals such as translucent paper, set them one by one.

Note

❒In Batch (SADF) mode, even when one original is set in the document feeder,

the original is automatically fed each time it is set.

APress the [

Special Original

]key.

BPress the [

Batch (SADF)

]key.

CPress the [

]key.

DSet your originals, then press the {

Start

}key.

The Auto Feed indicator of the document feeder goes on.

Setting Originals

EAfter all the previously set originals are fed, set the next originals while the

Auto Feed indicator is on.

The second and subsequent originals can be fed automatically without press-

ing the {

Start

}key.

Note

❒When the Sort, Combine or Duplex function has been set, press the {

}key

after all originals are scanned.

❒You can change the lighting-up time of the Auto Feed indicator. See “Batch

(SADF) Auto Reset Time” in ⇒P.329 “Input/Output”.

Mixed Sizes mode

When originals of different sizes are set on the document feeder at a time, the

machine automatically checks the size of the originals and makes copies.

Limitation

❒When setting originals of different sizes on the document feeder and making

copies without using Mixed Sizes mode, parts of the original image might not

be copied.

❒The weight of originals that can be set with this function is 52 – 81g/m2, 14 –

20 lb. Bond.

❒The original sizes that can be set with this function are as follows:

❒For smaller originals, the copy image might be slanted since the originals

might not be correctly aligned with the original guide.

Metric version A3L, B4L, A4KL, B5KL

Inch version 11" ×17"L, 81/2" ×14"L, 81/2" ×11"KL, 51/2" ×81/2"KL

DF02E

Otros manuales para 2555

Tabla de contenidos

Otros manuales de Impresora todo en uno de Savin

Manuales populares de Impresora todo en uno de otras marcas

Triumph Adler

Triumph Adler DC 2016 Manual

Epson

Epson WorkForce WF-2510 Guía del usuario

Epson

Epson Stylus Scan 2000 Manual de instalación y operación

Epson

Epson PictureMate Snap PM 240 Manual de instrucciones

Konica Minolta

Konica Minolta bizhub C35 Manual de usuario

Brother

Brother MFC-J430w Manual de usuario

Konica Minolta

Konica Minolta BIZHUB 558 Manual de usuario

Lexmark

Lexmark MX710 Series Manual

Brother

Brother MFC-9760 Manual de usuario

Lexmark

Lexmark XC8155 Manual de usuario

Lexmark

Lexmark X642E Manual de usuario

Sharp

Sharp MX-2310U Guía

Aficio

Aficio 200 Manual de usuario

Canon

Canon ImageCLASS 2300 Manual

Ricoh

Ricoh Pro C900 Manual de usuario

Lexmark

Lexmark X925 Manual de usuario

Brother

Brother Business Smart MFC-J4510dw Manual de usuario

Epson

Epson Stylus CX8400 Series Manual de usuario