Sarasota Key Captain Manual de usuario

Sarasota Quality Products • 27330 Center Ridge Road •Westlake • Ohio 44145

Ph: (440) 899-9820 ●Fx: (440) 899-0930 ●www.sarasotaqp.com 1

PRELIMINARY

Key Captain™ Remote Launching System

Installation Instructions

Sarasota Quality Products is a provider of security/access products for

the marine market. Products are designed to secure personal effects and

equipment, while providing safety, convenience, and launch assistance

for many types of watercraft.

PLEASE SAVE THESE INSTRUCTIONS

FEATURES:

Key Captain™ is a Remote Launching System that provides time saving

remote control launch functions for most boats.

• Lock & Unlock Compartment Latches

• Turn Bilge Blowers On & Off

• Trim Down & Up (Trailer Or Storage Position)

• Operate Auxiliary Functions (Cabin Lighting, Etc.)

• Designed For Easy Installation

• Corrosion Resistant Materials Used Throughout

• Unique System Sleep Mode

• Low Power Saving Operation That Extends Battery Life

• Floating Waterproof Remote Transmitter(s)

• On Site Programmable Remote Transmitter(s)

• Permanently Sealed Control Panel

• Audible Sounder Indicates System Operations

• FCC Compliant

SYSTEM COMPONENTS

CONTROL PANEL

FLOAT REMOTE

TRANSMITTER

SELS ELECTRIC

LOCK LATCH

WARNING:

Read and understand these instructions thoroughly before

proceeding with installation. Improper installation may result in

incorrect operation of the system.

 To prevent personal injury, always disconnect the battery leads

when installing or servicing this product.

 Power source must match the voltage rating of this product.

 Always use a fuse with amperage rating specified for this

system. Failure to do so may result in serious personal injury

or fire hazard.

Power Specification (Key Captain™ Control Panel)

Circuit Voltage Operating Current

Battery (Standby 15MA.) 9 – 16VDC 20 Amp

Lock 9 – 16VDC 10 Amp

Unlock 9 – 16VDC 10 Amp

Trim Up (see note) 9 – 16VDC 5 Amp

Trim Down (see note) 9 – 16VDC 5 Amp

Bilge Blower (see note) 9 – 16VDC 5 Amp

Note: Use BASIC WIRING INSTRUCTIONS except when current

requirements exceed fuse ratings shown, then, use ALTERNATE

WIRING INSTRUCTIONS.

Power Specification (Key Captain™ Electric Lock/Latches)

Circuit Voltage Current

Lock connection (Lt. Blue) 9 – 16VDC 0.5 Amp

Unlock connection (White.) 9 – 16VDC 0.5 Amp

Power Specification (Key Captain™ Transmitter)

Circuit Voltage Battery #

2 Coin Cell batteries 1.5 VDC ea. CR-2

REQUIRED FOR INSTALLATION

• Drill and suitable drill bit

• Hole saw

• Screwdriver

• Wire cutter/striper

• Crimp on wire connectors for 12, 16, & 18 gauge wire

• Cable tie-wraps

• Suitable stainless steel pan head screws

• Fuses as required

• Fuse holder for above fuses

• 12, 16, 18 gauge wire

INSTALLATION

MUST MEET APPLICABLE SECTIONS OF TITLE 33 CFR 183

SUBPART I, USCG REGULATIONS.

To prevent personal injury, always disconnect the battery leads when

installing the control panel, electric lock latches or connections to

auxiliary function devices.

The Key Captain™ control panel is designed for easy installation.

See separate installation instructions for mounting of Key Captain™

electrical lock latches.

MOUNTING INSTRUCTIONS

1. The Key Captain™ control panel may be positioned near the helm,

and in a secure area. The control panel may be secured to any

solid, flat mounting surface and oriented in any direction.

2. For security protection, the control panel should be mounted inside

a lockable compartment or other secure area.

3. For maximum reception of signals from the transmitter to the control

panel it should be located close to top level of the boat (see Fig. 1).

It should be mounted within 10 inches of a fuse distribution panel

(furnished by others).

4. Using the control panel as a template, mark holes for mounting feet

and drill holes. Secure control panel in place taking care not to over

tighten screws or penetrate hull.

BASIC WIRING INSTRUCTIONS

Note: Use BASIC WIRING INSTRUCTIONS except when current

requirements exceed fuse ratings shown in Power

Specification (Key Captain™ Control Panel), then, use

ALTERNATE WIRING INSTRUCTIONS.

1. Connect Key Captain™ control panel wires to fuse distribution

box: (Fig 2)

2. Connect control panel negative (green) wire to a good chassis

ground or negative post of battery (Fig. 2)

3. Use a quality marine grade stranded copper wire and connect

from fuse distribution box to the following circuits: (Fig 2)

4. Connect positive (+) battery (red) control panel circuit from

fuse distribution panel to the boat +12VDC battery post (Fig.

2).

5. Connect lock (light blue) control panel circuit wire from fuse

distribution panel to SELS 1000 electrical lock latches.

Observe polarity of wiring to connect to all light blue wires (Fig.

6. Connect unlock (white) control panel circuit wire from fuse

distribution panel to SELS 1000 electrical lock latches.

Observe polarity of wiring to connect all white wires together

(Fig. 2)

7. Connect trim down (pink) control panel circuit wire from fuse

distribution panel to trim down circuit input on trim controller

(Fig. 2)

8. Connect trim/trailer up (orange) control panel circuit wire

from fuse distribution panel to trim/trailer up circuit input on trim

controller (Fig. 2)

Sarasota Quality Products • 27330 Center Ridge Road •Westlake • Ohio 44145

Ph: (440) 899-9820 ●Fx: (440) 899-0930 ●www.sarasotaqp.com

9. Connect bilge blower (brown) control panel circuit wire from

fuse distribution panel to +12VDC wire on bilge blower (Fig. 2)

10. Do not make any connection to black wire on the Key

Captain™ control panel. This is the antenna wire and it is to

hang freely (Fig. 2)

OPERATING INSTRUCTIONS

Float Remote™ Transmitters control the operation/functions of the

Key Captain™ system. The operating range is 25-30 feet with direct

line of sight between the transmitter and control panel. The effective

range may diminish if direct line of sight is not available.

Five function buttons are located on top of the Transmitter.

Lock and Un-Lock operations are accomplished by momentarily

pressing the following push buttons.

Press and release to Lock all electric lock/latches.

Press and release to Un-Lock all electric lock/latches.

Bilge Blower operations are accomplished by momentarily

depressing the following push button.

Press and release to turn Bilge Blower ON

Press and release again to turn Bilge Blower OFF

Trim DOWN and Trim UP operations are accomplished by pressing

the following push buttons.

Press and hold until desired Trim DOWN position is reached.

Press and hold until desired Trim UP (Trailer) position is reached.

ALTERNATE WIRING INSTRUCTIONS

Note: Use ALTERNATE WIRING INSTRUCTIONS when current

requirements exceed fuse ratings shown in Power

Specification (Key Captain™ Control Panel). Auxiliary relays

are required to switch higher current trim motors and bilge

blowers. Auxiliary relays must be rated at 12VDC, 5 amp

maximum coils with normally open contacts (de-energized

state) that are rated for trim motor and bilge blower current

draw.

1. Connect Key Captain™ control panel wires to fuse distribution

box: (see Fig 3)

2. Connect control panel negative (green) wire to a good chassis

ground or negative post of battery (see Fig. 3)

3. Use a quality marine grade stranded copper wire and connect

from fuse distribution box to the following circuits: (see Fig 3)

4. Connect positive (+) battery (red) control panel circuit from

fuse distribution panel to the boat +12VDC battery post (see

Fig. 3).

5. Connect lock (light blue) control panel circuit wire from fuse

distribution panel to Key Captain™ electrical lock latches.

Observe polarity of wiring to connect to all light blue wires (see

Fig. 3)

6. Connect unlock (white) control panel circuit wire from fuse

distribution panel to Key Captain™ electrical lock latches.

Observe polarity of wiring to connect all white wires together

(see Fig. 3)

7. Connect trim down (pink) control panel circuit wire from fuse

distribution panel to coil of an auxiliary relay. Connect other

side coil wire to chassis.

8. Connect positive (+) battery to proper sized fuse. Connect

from fuse to one side of an auxiliary relay normally open

contact. Connect other side of auxiliary relay normally open

contact to trim down circuit input on trim controller (see Fig. 3)

9. Connect trim/trailer up (orange) control panel circuit wire

from fuse distribution panel to (+) coil of an auxiliary relay.

Connect other side coil wire (-) to chassis (see Fig. 3)

10. Connect positive (+) battery to proper sized fuse. Connect

from fuse to one side of an auxiliary relay normally open

contact. Connect other side of auxiliary relay normally open

contact to trim up (trailer) circuit input on trim controller (see

Fig. 3)

11. Connect bilge blower (brown) control panel circuit wire from

fuse distribution panel to coil (+) of an auxiliary relay. Connect

other side coil wire (-) to chassis (see Fig. 3).

12. Connect positive (+) battery to proper sized fuse. Connect

from fuse to one side of an auxiliary relay normally open

contact. Connect other side of auxiliary relay normally open

contact to+12VDC wire on bilge blower (see Fig. 3)

13. Do not make any connection to black wire on the Key

Captain™ control panel. This is the antenna wire and it is to

hang freely (see Fig. 3)

REMOTE FLOAT TRANSMITTER BATTERY REPLACEMENT

The Key Captain™, Remote Float™ Transmitter is powered by two coin

cell batteries (see Power Specification).

To replace the batteries, remove the top off of the unit by prying with

small screwdriver. Remove the circuit board. The two batteries are on the

under side of the circuit board.

Replace batteries. Replace circuit board. Reinstall cap while observing

alignment with key clip mounting hole. Used batteries should be

disposed of properly.

Properly installed the Float Remote™ has a watertight seal and is

watertight to IP-67 standards and will float with up to two small boat

ignition keys attached to the remote transmitter. Note: The transmitter

will not be replaceable under warranty after first customer battery

replacement.

Pry here to

remove the cap

from bod

Sarasota Quality Products • 27330 Center Ridge Road •Westlake • Ohio 44145

Ph: (440) 899-9820 ●Fx: (440) 899-0930 ●www.sarasotaqp.com 3

CONFIGURING THE SYSTEM OR REPLACING A TRANSMITTER.

Remote Float™ Transmitters are configured to the Key Captain control

unit at time of assembly or whenever a new transmitter is purchased.

Each control unit will need to be configured (learn) about all the

transmitters before the system will function.

1. To configure the system apply power the control panel (see

wiring instructions).

2. Press the plunger of the learn switch located on the control

panel. This will place the control panel in the learn mode and

will disable the lock/unlock features from operating.

3. With the control panel in the learn mode, press the lock button

on the transmitter for one second and release.

4. Wait one second then press the lock button again, but hold

and do not release.

5. The lock/unlock system will continue to be inoperable and will

not respond to the transmitter for another 10 seconds.

6. Once the control panel has learned about the transmitter it will

respond to the transmitter and actuate the lock/unlock system.

7. The control panel has learned about the transmitter and can

be used.

8. Repeat steps 1-8 to configure additional transmitters.

KEY CAPTAIN™ SLEEP MODE

The Float Remote™ will put itself into a power saving “sleep mode”

when inactive for several minutes. It will reactivate when any

pushbutton is pressed.

KEY CAPTAIN™ AUDIBLE MODE

Each time a Float Remote™ pushbutton is pressed the control

panel will produce an audible “chirp’ to acknowledge to the operator

that the transmitted signal has been received. The audible may be

permanently disabled by clipping the jumper wire on outside of

control panel case.

To permanently disable audible signal,

cut jumper wire.

Sarasota Quality Products • 27330 Center Ridge Road •Westlake • Ohio 44145

Ph: (440) 899-9820 ●Fx: (440) 899-0930 ●www.sarasotaqp.com 4

Sarasota Quality Products • 27330 Center Ridge Road •Westlake • Ohio 44145

Ph: (440) 899-9820 ●Fx: (440) 899-0930 ●www.sarasotaqp.com 5

Sarasota Quality Products • 27330 Center Ridge Road •Westlake • Ohio 44145

Ph: (440) 899-9820 ●Fx: (440) 899-0930 ●www.sarasotaqp.com 6

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including

interference that may cause undesired

operation.

Section 15.105 Information to the user Note: This equipment

has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception,

which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the

interference by one or more of the following measures:

__Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for

help.

-- Caution any changes or modifications not approved by

Delta Systems Inc voids user’s authority to operate this

equipment .

Manuales populares de Sistema de bloqueo de embarcaciones de otras marcas

Old Town

Old Town 01.1331.1987 Manual de usuario