Sanyo C14ZA25 Manual de usuario

INSTRUCTION MANUAL

Colour Television

Cl 4ZA20

Cl 4ZA25

Teletext (Model C14ZA25 only)

Special Function

AVInput &Output Terminal

Contents Warning

Warning ......................................................................... 2

Precautions ................................................................... 2

Aerial Connection ......................................................... 2

Battery installation (Remote Control Transmitter) ....... 2

Controls ........................................................................ 3

General Operation ........................................................ 4

Special Functions .......................................................... 8

Tuning of the Channels ................................................. 11

Teletext Use (Model C14ZA25 only) ............................ 13

Connecting other Equipment ........................................ 18

Specifications ................................................................ 20

To prevent fire or shock hazard, do not expose

the unit to rain or moisture.

High voltages are used in the operation of this

TV set. Do not remove the cabinet back from

your set. Refer servicing to qualified service

personnel.

Precautions

When the TV receiver is not to be used for an

extended period of time, it is advisabie to

Electric Mains disconnect the AC power cord from the AC

outlet.

The receiver is designed to operate on an A.C. mains

Sllppiy Of 220- 2@vOltS 50 Hz.

1( Matching box

To the aerial socket

Telescopic aerial

../

111111!!1111111111111111111111111111

!1!11!111!!11!1!1111111111111111111111111

1!!1111!11!!111!1!1111

1111!1!111!1111!11111 e.,

1r<erial socket

Connect the cable with aplug from

aUHF (or VHF) aerial to the aerial

socket on the cabinet back.

\Aefial cable

For all aerial circuit problems please consult your local

dealer.

❑Remove the battery cover by sliding.

❑Install two “AA 1.5 volt batteries so that the “+” and”-” marks on the batteries match the “+” and “-” marks

inside the unit.

I❑Close the battery cover.

Note: Replace the batteries when the TV set is showing the following symptoms:

Operation is unsteady or erratic, sometimes the TV set does not work with transmitter.

Discharged batteries may leak and damage the unit

The normal life of batteries should be from nine to ten months.

Controls

Remote Control

MEMORY/ PRESET

FUNCTION ~UP/DOWN Main ON/OFF

switch

,<,,,.

–3–

General Operation

“o “00

To switch on or off the TV; To set the TV to standby mode;

Press the Main ON/OFF ~

button.

The power of the TV is turned on,

or off completely.

Important !

Be sure to set the Main ON/OFF switch

the power failure occurs while viewing.

mm’

+.:.:.:.:.:.:~.:.:,:,:,:,:,:.:

..:.:::A:::.:.:.:.::.:..

,...........

..’xL-x

/!!)8 6

sss the Power ON/OFF button ~

To turn on theTV, press again.

Oto the off position, if

To turn on the TV from standby

mode;

Press (J

Power ON/OFF ~

(remote control transmitter)

,.,.,.,.:.:.:.,V::.,.,.

. . . . . . . . . .’.”.:......<pw+.A :::::::::::::

VT ,,,,,

.,,.,, ,,,,,

...... ,,,,,

.,,..,,.,

......

,,..

Programme UP/DOWN o

(remote control transmitter)

1to 9, 0Key

P(remote control

transmitter)

or -d+TPA

mProgramme

UP/DOWN @

(TV set)

\AUTO SHUT OFF I I

This TV set incorporates the AUTO SHUT OFF function. Remaining time

Even if the TV is left on after you have gone to sleep, the TV set changes

to the standby mode within 10 minutes after all broadcasts have ended.

–lo

To select aprogramme directly For example;

Programr

Selector

Digit

To select aprogramme 8

fTo select aprogramme 10

-1--*

,6Press the Digit ~key. 1

=-l ’67810,

(To select aprogramme 27

-/--*

,(7

?ti.rz?ld

–4–

General Operation

To select achannel

Remote Control Transmitter

[

Front controls of the TV

or oFQ -A +VPA

W’

Programme UP/DOWN

To adjust the sound volume

IdSOUND

111111 --------- LEVEL

To display the on screen indications, press the RECALL

key.

..........p.. ...+.+..A.;.:.:.:.,.,.. =

‘fftimer+291’

Screen display disappears after

about 5seconds.

Press the ALTERNATE @key, and the programme position

alternately select the previous position and the present position,

~’..’.t

,,,,,,,,,,,,,,,,,,.,,,,,

...,. I-v/mPAP

-Q

ALTERNATE

–5–

will I

For example, now you are watching programme position

“4” but you watched programme position “2” previously. If

you press the ALTERNATE key, programme position “2”

immediately appears.

General Operation

Should you wish to mute the sound (e.g. While talking on

the telephone), press the SOUND MUTE ~key.

,,,.,,,

Q‘Om ‘g

00 ~SOUND MUTE

ASOUND MUTE

111111 ---------

To switch the sound back on,

press SOUND MUTE key again.

The TV set will be turned off after about 30,60,90 or 120

Press the OFF TIMER ~key.

~:~ ....

,.,,,.,

!FGI[ -.+ lv/~ P*P

q:0 ~

o\~OFFTIMER

To cancel the OFF TIMER

Press the OFF TIMER key until”- –“appears.

minutes.

I‘- ++30-+1-6CI

No off timer After 30 minutes After 60 minutes

L+ I-120 +1 -90

After 120 minutes After 90 minutes

IJust one minute before switching off the TV, “–01” ‘

and channel number will be displayed on the

screen.

Y– 01 25

IIII

This function lets you store the settings (for colour, brightness, contrast, sharpness, sound volume)in memory for both

picture and the sound, and these setting levels can be recalled by pressing the NORMALIZATION @key of the remote

control transmitter.

To store the picture and sound settings

(1) Set the picture and sound to the desired levels. —> ASOUND

111111--------- etc.

(2) Press the MEMORY/PRESETO ~button while the control function display is still visible on the screen,

orQ rfyfy .1 ->1 .!y’’’’:’- I

~MEMORY/ PRESET -

NOTE: The control settings will not be saved if the MEMORY button is pressed after the control function display has

left the screen.

[,!

IFQ:

~,~ -.+’’”’”’”:,=‘o:”

‘e ~M

Press the NORMALIZATION @key.

*The colour, brightness, contrast, sharpness and

NORMALIZATION sound volume settings which you stored using the

MEMORY button are recalled.

–6–

General Operation

(1) Select the adjustment item using the FUNCTION Okey. (2) Adjust using the LEVEL @+ and –key.

-II

LEVEL

or aI

oFQ -A+ TPA

iEVEL

Each time the FUNCTiON ~key is pressed, function choice wiii change as foiiows;

@COLOUR

11111111111 ----

Coiour intensity

~BRIGHT

11111111111 ----

IBrightness

Il+

I I <>

II1

~CONTRAST

11111111111 ----

Contrast

+IUISHARPNESS

------- t-i-----

Dispiay off Fine tuning Sharpness

(Operative for TV mode oniy)

–7–

Special Functions

You can set the special functions by inputting the special codes usingthe RECALL@ key and the Programme Selector=

of the remote control transmitter.

Special codes and special functions are as follows

special Special functons

code

SP 00 Reset all special functions (The start condition for the TV power is changed to the standby start).

SP 01 Reset all special functions.

SP 30 Cancellation special code “31”.

SP 31 Maximum volume level setting and prohibition of channel tuning function.

SP 40 Setting of the startup condition for the TV programme.(Always switched on in previous programme position)

SP 41 Setting of the startup condition for the TV programme. (Always switched on in programme position”1” )

SP 42 Setting of the startup condition for the TV programme. (Always switched on in programme position “T )

SP 43 Setting of the startup condition for the TV programme. (Always switched on in programme position”~ )

SP 44 Setting of the startup condition for the TV programme. (Always switched on in programme position “4” )

SP 45 Setting of the startup condition for the TV programme. (Always switched on in programme position “5” )

SP 46 Setting of the startup condition for the TV programme. (Always switched on in programme position”6 )

SP 47 Setting of the startup condition for the TV programme. (Always switched on in programme position “7”)

SP 48 Setting of the startup condition for the TV programme. (Always switched on in programme position “8” )

SP 49 Setting of the startup condition for the TV programme. (Always switched on in AV mode)

SP 50 Change of the start condition for the TV power (Setting to the standby start).

SP 51 Change of the start condition for the TV power (Setting to the normal start).

SP 60 Cancellation special function 61.

SP 61 Suppression of the auto shut off function.

Note: Special functions are not cancelled when the power is turned off or when the AC power plug is disconnected from

the mains.

Example: To input special code “49” (The input method is the same for all the special codes.) I

(1) Press and hold the RECALL ~key for more

than 3seconds.

Baw

:.::.::.:.::

V,:,:.:.:.:.:.:.:y’x’x “.”’”.”’.”.

((—G, .......

...........

,.:.;.:.:.:.,.:.n.;.:.:.:.;.:&..:.;.:...... . ........

2“3:-...:

~RECALL

LPI-2 4$$

(2) Press” 4” key, next press”

b h (M

b b 78

‘bad

.......

............... .:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.

., ,.,.,

:....”

,.,.-, ,.,.,

key. 1

SP49

-●

(3) Press MEMORY/PRESET ~button of the TV set.

Q‘-e

MEMORY/ PRESET u

-8–

Special Functions

■When “SPO1” is input, all special functions are reset.

9When “SPOO” is input, all special functions are cancelled, and the start condition for TV power is changed to the

standby start condition, meaning that the picture will not appear even when the mains ON/OFF switch ~is set at the

on position. To turn on the TV set from the standby mode, press the Power ON/OFF,~,Programme UP/DOWN @or

Programme Selector ~key.

“SP31” is used to set alimit for the maximum volume level while keeping the current preset programme position in

memory.

When “SP31” is entered, the volume output at the time of entering the code is placed in the memory as the maximum

volume level. In other words, with this code it is possible to set the maximum volume at your preference. Entering this

code automatically suppresses the preset function, so that even if the preset button is pressed, the preset mode will

remain inactive,

(1)Set the disirable volume level using the LEVELO key.

~LEVEL IASOUND

11111111 -----”

(2j Input “SP31”.

The volume level set in this

procedure will be memorized

as the maximum volume level.

To cancell “SP 31”, input “SP 30”.

When “SP 50” is entered, the start condition of the TV power is set to the standby start condition, meaning that the picture

will not appear even when the Mains ON/OFF switch ~is set at the on position(The TV set remains in standby mode).

To return the TV’s power start condition to its original condition(normal start condition), input “SP51”.

When “SP 61” is entered, the auto shut off function is suppressed.

AUTO SHUT OFF

(Refer to page 4)

‘L

–lo

To cancell “SP61”, input “SP60”.

–9–

Special Functions

These functions can be used to change the startup condition of the TV set as follows;

When “SP40” is input

~2L Previous”

programme

position

When “SP41” is input When “SP42” is input

The TV will always switch on in The TV will always switch on in

programme position 1. programme position 2.

The previously viewed programme

position is always selected.

“SP43” ,,sp44,, “SP45”

(+’I7 H-J 8+7

“SP46” ,,sp47,, ,,Sp48,,

,}sp49,,

/!%7

The TV will always switch on in

AV mode.

–lo–

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de TELEVISOR de Sanyo

Sanyo

Sanyo AVM-3651G Manual de usuario

Sanyo

Sanyo DS20424 Manual de usuario

Sanyo

Sanyo CE21D4-C Manual de usuario

Sanyo

Sanyo CP14SA1 Manual de usuario

Sanyo

Sanyo DP23625 Manual de usuario

Sanyo

Sanyo CP21SW1Z Manual de usuario

Sanyo

Sanyo CE21DN3-C Manual de usuario

Sanyo

Sanyo LCD-42K30TD Manual de usuario

Sanyo

Sanyo CE14SA4 Manual de usuario

Sanyo

Sanyo CZP2530TXN Manual de usuario

Sanyo

Sanyo AVM-2550S, AVM-2759S Guía de instalación

Sanyo

Sanyo AVM-3259G Manual de usuario

Sanyo

Sanyo LCD-DP55441 Manual de usuario

Sanyo

Sanyo 28D2 Manual de usuario

Sanyo

Sanyo DS19500 Manual de usuario

Sanyo

Sanyo C14ZA20 Manual de usuario

Sanyo

Sanyo LCD-24K40 Manual de usuario

Sanyo

Sanyo CE21B4-C Manual de usuario

Sanyo

Sanyo CE27LD5-B Manual de usuario

Sanyo

Sanyo CEP2576D Manual de usuario

Sanyo

Sanyo CE32LD81 Manual de usuario

Sanyo

Sanyo AVM-3651G Manual de usuario

Sanyo

Sanyo DP46840 - 46" Diagonal LCD FULL HDTV 1080p Manual de usuario

Sanyo

Sanyo DP50741 Manual de usuario

Manuales populares de TELEVISOR de otras marcas

Philips

Philips Colour Television Manual de usuario

Toshiba

Toshiba 27A10 Manual de usuario

Philips

Philips 42PF9630A/37 Manual de usuario

Hitachi

Hitachi 32FX48B Manual de usuario

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Manual de usuario

Changhong Electric

Changhong Electric uhd55b6000is Manual de usuario

Philips

Philips Matchline 21CE7551 Manual de usuario

Panasonic

Panasonic Genus TX-G10 Manual de usuario

Toshiba

Toshiba 19A20 Manual de usuario

Philips

Philips 25PT4523-16 Manual de usuario

Sony

Sony XBR-100Z9D Manual de usuario

Philips

Philips PR0930X3 Manual de usuario

Philips

Philips Brilliance 231P4QPY Manual de usuario

Samsung

Samsung 55S9 B Series Manual de usuario

Philips

Philips 32HF9385D Guía de solución de problemas

Sharp

Sharp LC-40FI5012E Manual de usuario

Loewe

Loewe Table Stand Reference 55 Manual de usuario

Philips

Philips 32PFH5300 Manual de usuario