Sanyo VCC-3700P Manual de usuario
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
COLOUR CCD Camera
CCD-Farbkamera
Caméra CCD COULEUR
CCD
VCC-3700P
VCC-3770P
About this manual
•Before installing and using the camera, please
read this manual carefully. Be sure to keep it
handy for later reference.
•This manual gives basic connections and
operating instructions for 2 PAL models
( CC-3700P, 3770P).
Über diese Bedienungsanleitung
•Lesen Sie bitte vor der Montage und dem
Inbetriebnehmen der Kamera zuerst diese
Bedienungsanleitung sorgfältig durch und
bewahren Sie sie zum späteren Nachschlagen
auf.
•In dieser Anleitung finden Sie die Anschlüsse
und die Grundbedienung für 2 PAL-Modelle
( CC-3700P und 3770P)
•
!
•
"#
2
$
PAL
%
(VCC-3700P,
3770P)
&'()*+,-!
À propos de ce manuel
•Avant d’installer et d’utiliser la caméra, veuillez
lire ce manuel attentivement. Gardez-le à
portée de main pour toute référence ultérieure.
•Ce manuel couvre les branchements et
instructions pour l’utilisation de base pour 2
modèles de format PAL ( CC-3700P et 3770P).
L53M5, N5/XE GB 1996, 8, 6
Depending on the conditions of use,
installation and environment, please be
sure to make the appropriate settings and
adjustments. If you need help with
installation and/or settings, please consult
your dealer.
CONTENTS
PRECAUTIONS...................................................2
PARTS NAMES...................................................3
MOUNTING THE LENS......................................5
CONNECTIONS..................................................7
SETTINGS...........................................................9
TROUBLESHOOTING.......................................13
SPECIFICATIONS .............................................13
ACCESSORIES
1C mount adaptor ( mm)................ 1 pc.
The C mount adaptor must be used to
be able to install a C mount lens on the
camera.
2Lens iris plug (4-pin) ........................1 pc.
12
FEATURES
•Built-in interline transfer method 1/3"
CCD
– Model VCC-3700P approx. 320,000
picture elements
– Model VCC-3770P approx. 470,000
picture elements
•Low smear, anti-blooming, low lag, no
burning and no geometric distortion
using the CCD solid state image device.
•100% solid state components giving
excellent immunity to shock and
vibration
•Not subject to interference from
magnetic or electrostatic fields
•High sensitivity, minimum required
illumination
– Model VCC-3700P 1.4 lux with F 1.2
lens
– Model VCC-3770P 2 lux with F 1.2
lens
•Horizontal resolution
– Model VCC-3700P more than 330 TV
lines
– Model VCC-3770P more than 460 TV
lines
•Built-in high speed electronic shutter
(with selectable speed setting by
internal switches)
•New backlight compensation function
(Active when using an auto-iris lens)
•Externally adjustable flange back
(mechanical focus)
•Low power consumption and quick start
•Separate Y and C signal outputs: Model
VCC-3770P only
L 3M , N /XE GB 1996, 8, 6
English 1
PRECAUTIONS
In case of problem
Do not use the camera if smoke or a
strange odour comes from the unit, or if it
seems not to function correctly. Disconnect
the power cord immediately, and consult
your dealer (or a Sanyo Authorized Service
Centre).
Do not open or modify
Do not open the cabinet, as it may be
dangerous and cause damage to the unit.
For internal settings and repairs, consult
your dealer (or a Sanyo Authorized Service
Centre).
Do not put ob ects inside the unit
Make sure that no metal objects or
flammable substance get inside the camera.
If used with a foreign object inside, it could
cause a fire, short-circuits or damages.
If water or a liquid gets inside the camera,
disconnect the power cord immediately,
and consult your dealer (or a Sanyo
Authorized Service Centre). Be careful to
protect the camera from rain, sea water,
etc.
Be careful when handling the unit
To prevent damages, do not drop the
camera or subject it to strong shock or
vibration.
Install away from electric or
magnetic fields
If installed close to a TV, radio transmitter,
magnet, electric motor, transformer, audio
speakers the magnetic field they generate
will distort the image.
Protect from humidity and dust
To prevent damages to the camera, do not
install it where there is greasy smoke or
steam, where the dampness may get too
high, or where there is a lot of dust.
Protect from high temperatures
Do not install close to stoves, or other heat
generating devices, such as spotlights, etc.,
or where it could be subject to direct
sunlight, as that could cause deformation,
discoloration or other damages.
Be careful when installing close to the
ceiling, in a kitchen or boiler room, as the
temperature may raise to high levels.
Install where the temperature range will
stay between –10˚C and 0˚C.
(no condensation)
Cleaning
•Dirt can be removed from the cabinet
by wiping it with a soft cloth. To
remove stains, wipe with a soft cloth
moistened with a soft detergent
solution and wrung dry, then wipe dry
with dry soft cloth.
•Do not use benzine, thinner or other
chemical product on the cabinet, as that
may cause deformation and paint
peeling. Before using a chemical cloth,
make sure to read all accompanying
instructions. Make sure that no plastic
or rubber material comes in contact
with the cabinet for a long period of
time, as that may cause damage or
paint peeling.
ENGLISH
L 3M , N /XE GB 1996, 8, 6
2 English
PARTS NAMES
1Power indicator (POWER)
Comes on when the power to the camera is on.
2Video output connector (VIDEO OUT: BNC type)
Connect this connector to a device such as a VCR or monitor
with a VIDEO IN connector.
3AC power cord
4External sync composite video signal input connector
(VBS IN: BNC type)
Connect to this connector the synchronizing signal output
from a synchronizing signal device or the composite signal of
a video distributor.
5Line phase ad ustment screw (LINE PHASE)
When using two cameras or more, the image on the
monitor may roll vertically when switching sources. This
rolling can be minimized by turning this screw.
6Y/C OUT connector (4 pin)
Separate Y (luminance) and C (chroma) signals are output
from this terminal.
A better picture quality is obtained if the monitor or VCR is
connected to this connector.
1Y signal ground 2C signal ground
3Y signal: 1.0 Vp-p, 7 ohms, unbalanced, negative sync
4C signal: 0.3 Vp-p, 7 ohms, unbalanced
7Lens mount cap
The cap is installed to protect the lens mount section.
Remove the lens mount cap before installing a lens (sold
separately).
8Camera installation bracket
The bracket can be fixed at the top or bottom of the
camera. When fixing the bracket, be sure to use the longer
screws and install the shorter screws on the opposite side to
seal the openings.
CAUTION:
When installing the camera support, select a location
that can support the total weight of the camera and
accessories.
1
3
2
5
4
(VCC-3700P)
1
3
2
5
4
(VCC-3770P)
6
12
43
1232
1
7
8
1Shorter screws: M3 x 4
2Longer screws: M3 x 6
3Camera mounting screw
hole: 1/4"-20 UNC
L 3M , N /XE GB 1996, 8, 6
English 3
9Lens iris output connector (4 pin)
This 4-pin connector is used to send the DC control signal
and power supply to an auto-iris type lens.
FCamera setup section (under the cover)
This unit factory settings are as indicated below. These
settings are for when using a 1/3 inch CS mount DC
(without EE internal amplifier) type lens. However, if due to
installation conditions or environment the settings may need
to be modified for best results (see page 9 "SETTINGS"). To
access the controls, remove the cover fixing screw, then
remove the cover.
Control name Position
aAuto gain control switch (AGC) ON
bInternal/Line lock switch (SYNC) INT
cHigh speed electronic shutter
switches (E.S.) All OFF: 1/50 sec
dWhite balance switch (WB) A
eRed and Blue colour
ad ustment volume (R, B) about centre
fElectronic iris (EI)/
Backlight compensation (BLC)
switch
OFF
gAuto-iris lens switch (A.I. LENS) DC
hLens iris level volume (LEVEL) about centre
Note:
•The EI/BLC switch is used for an auto-iris lens, therefore
the two settings cannot be used simultaneously.
•When using a 1/2 or 2/3 inch C mount VIDEO (with EE
internal amplifier) auto-iris type lens, set the A.I. LENS
switch to the VIDEO position.
F
4
1
2
3
9
a
ON
OFF
ON
LEVEL
DC
VIDEO
A. I.
LENS
LH
VR301
23
OFF
ON
H-P
AGC FL
SC-P2
SYNC
L-L
INT
VR302
WB
A
M
4
BLC
EI
SC-P1
O
N
O
F
F
1
VR311
VR312
BR
E
I
VR303
b
c
d
f
g
h
e
L 3M , N /XE GB 1996, 8, 6
4 English
PARTS NAMES
GFlange-back ad ustment screw (FLANGE BACK ADJ.)
HFlange-back lock screw (FLANGE BACK LOCK)
Flange-back ad ustment
If the pick-up surface is not correctly positioned with relation
to the lens focal point, the picture will be out of focus (in
particular when using auto-iris power zoom lenses, sold
separately). If that is the case, adjust the flange-back position
as described below.
1Using a + screwdriver, loosen the FLANGE BACK LOCK
screw (M2:+).
Set the zoom lens to the maximum telephoto position,
set the focus using the focus ring on the lens.
2Set the zoom lens to the maximum wide angle position,
set the focus using the FLANGE BACK ADJ. screw.
3Repeat steps 2 and 3, until the image stays in focus when
changing from a telephoto shot to a wide angle shot.
When the setting is complete, tighten the FLANGE
BACK LOCK screw.
MOUNTING THE LENS
Check the lens mount
Do not use a lens if the length “L” is more than 5 mm.
That may damage the camera and prevent proper
installation.
Installation of a DC type auto-iris lens (sold
separately)
A 1/3 inch CS mount type lens without EE amplifier circuit
that only uses a DC power source. This camera can receive
(the A.I. LENS switch to the DC type) a CS mount type lens
without the need of an adaptor.
If the lens plug shape or wiring does not correspond, please
install the supplied plug as indicated in the pin layout table.
L
1H
G
1
3
LOCK
2
ADJ.
L 3M , N /XE GB 1996, 8, 6
English 5
MOUNTING THE LENS
DC
VIDEO
4
Installation of a VIDEO type auto-iris lens
(sold separately)
A 1/2 or 2/3 inch C mount type lens with EE amplifier circuit
that uses the video signal and a DC power source.
1Remove the lens mount cap.
2Attach the supplied C mount adaptor (A) to the
auto-iris lens (B), then install the assembly on the camera.
3Connect the lens plug to the LENS connector on the side
of the camera.
If the lens plug shape or wiring does not correspond to
the specifications below, connect the supplied plug as
indicated.
•When using lenses from other makers, make sure that
the pins connections in the plug correspond to the
ones of the camera.
Refer to the lens specifications to check the pins
connections in the plug.
•If they are different than indicated, remove the original
plug and connect the supplied plug according to the
diagram.
4Set the A.I. LENS switch in the camera setup section to
the VIDEO position.
Pin layout
DC type lenses VIDEO type lenses
1Brake coil (–) +12 V DC ( 0 mA max.)
2Brake coil (+) Not used
3Drive coil (+) Video output (1.0 Vp-p, high
impedance)
4Drive coil (–) Ground (for video signal and DC
power)
2 (A) (B)
3
31
2
4
L 3M , N /XE GB 1996, 8, 6
6 English
MOUNTING THE LENS
If using Sanyo (DC type) auto-iris lens
•VCL-CS8LY: Standard angle, f= 8 mm
•VCL-CS4LY: Wide angle, f= 4 mm
•VCL-CS2LY: Ultra-wide angle, f= 2.8 mm
If using a VIDEO type auto-iris lens
•Set the ALC and LEVEL controls on the lens to adjust the
iris. Normally the ALC volume should be turned all the
way to Av (Average).
•Depending on the type of lens used, the lens may not
perform properly. In such a case, adjust the LEVEL
volume on the lens casing to correct.
Compatible auto-iris lenses
•f= 9 mm (Standard angle), f= 12 mm (Telephoto),
f= 16 mm (More telephoto)
(A)
1
2
(Video signal connections)
: VIDEO IN
: VIDEO OUT
(VCC-3700P)
CONNECTIONS
Basic co ectio for mo itori g or recordi g
The peripheral devices (VCR, monitor, lens, etc.) and
cables are sold separately.
1Make the video signal connection between the camera
and the monitor or time lapse VCR.
2Insert the plug of this power cord into a wall outlet.
The POWER indicator (A) will light. Adjust the picture on
the monitor using the Brightness and Contrast controls.
Coaxial cable type and maximum length
•Cable type RG- 9U, 100 m maximum.
•Cable type RG-39U, 200 m maximum.
CAUTION:
The RG- 9U type cable should not be run through electrical
conduits or through the air.
L 3M , N /XE GB 1996, 8, 6
English 7
CONNECTIONS
Co ectio s to the camera Y/C OUT co ector
The peripheral devices (VCR, monitor, lens, etc.) and
cables are sold separately.
1Using a coaxial cable (twin type, 7 ohms), connect the
Y/C OUT connector from the camera to the S-VIDEO
input terminal on the monitor or time lapse VCR.
2Insert the plug of this power cord into a wall outlet.
Then, turn on the power of all the devices connected to
the camera.
The POWER indicator (A) will light. Adjust the picture on
the monitor using the Brightness and Contrast controls.
CAUTION:
•Please use a monitor with a Y/C or S-VIDEO input
terminal, or a time lapse VCR with a S-VIDEO input
terminal.
•Use a Mini-DIN (round type, 4-pin) plug to connect to the
Y/C connector.
Never use a coaxial cable longer that 10 metres to
connect the camera to the S-VIDEO input terminal.
(Video signal connections)
: Y/C or S-VIDEO IN
: Y/C or S-VIDEO OUT
(A)
2
1
(VCC-3770P)
L 3M , N /XE GB 1996, 8, 6
8 English
SETTINGS
AGC setting
AGC (Automatic gain control) can be turned ON or OFF.
ON: Auto gain control
OFF: Fixed gain
Line phase ad ustment
When using a camera switcher to connect 2 cameras or more to
one monitor, there may be a vertical roll of the images when
switched. In such a case, set as described below.
1Set the SYNC switch to the L-L position.
2Switch the display on the monitor from camera 1 to camera 2.
Adjust the LINE PHASE volume on camera 2 until the vertical
roll of the image stops.
If more than two cameras are used, please repeat this
procedure for all the cameras.
CAUTION:
If the vertical roll cannot be corrected by setting the LINE PHASE
volume on camera 2, try setting the LINE PHASE volume on
camera 1. If it still cannot be corrected, please check that the
polarity of the power cords of all connected devices is correct.
ON
OFF
ON
LEVEL
DC
VIDEO
A. I.
LENS
LH
VR301
23
OFF
ON
H-P
AGC FL
SC-P2
SYNC
L-L
INT
VR302
WB
A
M
4
BLC
EI
SC-P1
O
N
O
F
F
1
VR311
VR312
BR
E
I
VR303
SYNC
L-L
INT
OFF
ON
AGC
L 3M , N /XE GB 1996, 8, 6
English 9
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cámara a color de Sanyo
Manuales populares de Cámara a color de otras marcas
Gadgets and Gear
Gadgets and Gear Desktop Spy Clock Hidden Camera Instrucciones de montaje
General Security
General Security MTX600HQ Manual de usuario
WofVision
WofVision EYE-12 Manual de usuario
Leopard
Leopard LI-1080PTZOV Manual de usuario
Microscan
Microscan QX Hawk Manual de usuario
Imperx
Imperx CHEETAH C4080M Instrucciones de uso