Sangean UCR-1000FM Manual de usuario

12 13 14

MONOMONO

STEREOSTEREO

FMFM

MHZMHZ

Notes on safety

Please observe the following instructions:

The radio should only be connected to 230v / 50HzA.C..

We recommend that you disconnect the power cord from the

mains during extended absences.

Theambient temperature should not exeed 35 C. Avoid

locations close to radiators and do not expose direct sunlight.

Ensure that the system is sufficiently ventilated.

Protect system from dust, condenstion and water.

Avoid strong magnetic fields, i.e. do not locate unit close to

Tvs and loudspeakers of other units.

Do not use strong chemical detergents whencleaning the unit

and do not grease or lubricate any machine parts.

For service, consult your authorised dealer

=On/off switch

=Automatic Tuning System

=Display for: Power on/Stereo

=Switch for FM reception Mono/Stereo

=Antenna adjustment for the satellite clock

=Setting frequencies/station search

to higher frequencies

=Display

=Short-term alarm

=Entering beeper alarm-time

=Switching on and selecting the alarm

functions

=Keys for entering station numbers

and time

0=Switching from time to frequency

display

=Volume dial

=Setting frequencies/station search

to lower frequencies

=Entering the alarm time for radio

Elements of operation - summary

2.1 Radio

ATS

/ST

FM MONO STEREO

1/2

TUNING

1 - 0

0...99

Installing the appliance

The installation diagram can be found on the rear fold-outpage.

Your clock radio is designed to be installed under borders, kitchen

cupboards or shelves etc. The front of the loudspeakers must be

mounted pointing downwards and be free of obstructions to ensure

the best possible sound quality.

Toavoid the appliance being damaged by rising steam please do

not install the appliance above or next to a stove.

The clock radio is to be affixed in the desired place using bracket .

Tosimplify the mounting procedure the bracket can be removed

from the appliance by unscrewing retaining screws and .

Please use the enclosed drilling stencil for attaching the bracket

without measuring:

1.Attach the drilling stencil to the underside of the cupboard or

shelf with adhesive tape.

2.Mark the 4 drilling holes, remove the stencil and pre-drill at

the places marked.

3.Unscrew the 4 retaining screws and and carefully separate

bracket from the radio.

4.Now you can mount the bracket with the 4 short screws.

If necessary you can increase the distance between the bracket

and the underside of the shelf (thus also the distance between

the radio and the shelf ) with the spacers. Please use the longer

screws when employing the spacers.

5.Slide the radio onto the mounted bracket and tighten retaining

screws and in the desired position. Use a coin or suitable

screwdriver to tighten screws and .

6.Completely unwind the FM antenna. Using a good quality adhesive

tape, stick the antenna to the underside of the shelf or cupboard.

Installation material (enclosed):

4 screws short

4 screws long

4 spacers

Initial connection

4.1 Setting the satellite controlled time

Plug the mains plug into a 230V / 50Hz AC socket.

As soon as the appliance is plugged into the power supply the entire

frequency range of the radio is searched for stations.

A maximum of 20 stations will be programmed into the station keys

1-10 in accordance with their reception quality.

After the programming is completed these stations can be played

by pressing the appropriate buttons 1-0.

For two-digit numbers, enter the tens number and then the ones

number via keys 1-0.

Every press of a button is confirmed by a signal tone.

Note

Although you can select a station immediately after the search

procedure, we recommend to wait until the satellite controlled

time has been set. Otherwise the automatic setting of the time

can take longer than necessary.

After the programming procedure for the stations is finished,

appears in the display with the colon flashing to show you that

the satellite signal for the time setting of the appliance is being

searched for.

Once the signal has been received, the symbol blinks in the display

and the seconds :00 to :59 are displayed in a one minute cycle.

After a few minutes the display shows the correct time.

The symbol now appears uninterrupted in the display.

This means that the connection has been made to the time transmitter.

At regular intervals the appliance compares the set time with the radar

signal from the time transmitter and ensures that the clock always

shows the exact time.

The changeover from summer to winter time is also controlled

automatically by the time transmitter.

Note

If the radio cannot receive the time transmitter (the colon is not

blinking and the symbol is not in the display), slide switch

to 2

If the clock radio does not receive the time signal with the switch at

2 you can also set the time manually.

First press key and enter the correct time using the number

keys 1-0 while holding this key down.

E.g.:12:08 pm = number keys 1, 2, 0, 8.

Release key The colon between the hour and the minute

display blinks and the time which you have entered appears in

the display.

Note

Whenever the radio is turned off at the on/off switch the radio

will attempt to receive the time transmitter.

If the signal is received (symbol blinks), the appliance automatically

sets the clock at the correct time. In the display the symbol is

shown in addition to the time .

You can call up stations from the pre-programmed station memories

or using the station search.

You can turn the radio on either with the on /off switch or

directly by entering the station number with keys 1-0 .

The display /ST servers as switch on control. It lights up red

(mono reception) or green (stereo reception )when the appliance is

turned on. The volume can be adjusted using the volume dial

Switch the radio on directly by pressing one of the station keys 1-0 .

In the display the frequency and the memory number of the selected

station appears.

Keys and are for tuning to stations which have not been

Stored by the automatic tuning system (ATS)

Innitial connection / Radio play

4.2 Setting the time manually

5 Radio reception

5.1 Calling up stations from the station memory

5.2 Station search

Press the keys briefly and the appliance moves 100kHz higher

( key )or lower frequencies ( key )

Holding key or pressed for a short time, starts the station

search which stops at the next station received.

If a station is received which is already in the memory, M appears

in the display followed by the applicable station number

If the automatic tuning system (ATS) is to be restarted press

the ATS key for more than 2 seconds.

The automatic station search with the programming of the station

keys starts just as when initially connecting the radio.

Due to changes in the reception quality other stations can also be

stored

Tune in to your desired station. To store the station at a particular

station number you must:

a)for the single digit station numbers 1-9 press and hold the

desired

station-key for more than two seconds;

b)and for the double digit station numbers 10-20 press the tens

digit of the station number (i.e,1 or 2) briefly then press and hold

the ones digit of the station number (1-0) for more than two

seconds.

The storing of the station is confirmed by the signal tone.

In the display you will see the frequency and followed by

the station number which you have just entered.

Example: Storing a station at station number 19:

Tune in to the station you wish to store. Press the station key

briefly. Press and hold station key until the storing is confirmed

by the signal tone. The station is now stored, in the display you will

see the frequency you are tuned to and M 19

Note

The station previously at this station number is erased by the new

station.

Radio play

5.3 ATS

5.4 Storing stations manually

For example, to play the first station with station key 1 and to receive

the second station with station key 2, the order of the stations from

the automatic programming can be changed.

Example:

The first program is at station key 16 and should be played at

Station key 1.

First press station keys 1 + 6

Then press and hold station key 1 for approx. 2 seconds.

The successful reprogramming is confirmed by the signal tone.

The first station is now at station key 1 and the station previously

stored at station key 1 is now stored at station key 16.

When switching on the appliance at the on/off switch the last

station heard is played again.

The last frequency heard appears briefly in the display.

After a few seconds the time is displayed.

To receive stereo stations, the switch FM must be at STEREO.

If a stereo station is being received the display /ST lights up

green.

If the reception signal is weak or disturbed by static, it is better to

switch to MONO.

When the appliance is turned on you can switch between the time

and frequency displays by briefly pressing station key 0 .

Radio play

5.5 Interchanging two pre-programmed stations

5.6 Last Station Memory

5.7 Stereo reception

5.8 Switching between frequency and time displays

6.1 Automaticswitch-on-alarm

Your appliance has two independent alarm memories; one for

the alarm with radio and one for the alarm with the beeper.

Switch the alarm function on with key . By repeatedly pressing

key you can choose between radio alarm (display ), beeper

alarm (display ) and the alarm with both beeper and radio (display + ).

Beeper alarm

1.Selecting the beeper alarm

Press key / until the symbol appears in the display.

2.Setting the alarm time

To set the alarm time press and hold key SET and enter

the desired time using the number keys .

Example: Alarm time 9:30 am keys 0, 9, 3, 0

After releasing key SET the alarm time is active

The symbol and the alarm time are displayed to show that

the automatic function is on.

The beeper sounds at the programmed time.

3.Switching the alarm off

To turn the appliance off press key .

The beeper switches off automatically after one hour if key

is not pressed.

The appliance switches on automatically at this time every day

as long as the symbol is lit in the display.

Alarm with radio

Tune in to the desired radio station and set the volume.

1.Selecting the radio alarm

Press key / until the symbol appears in the display.

Timer

Otros manuales de Radio de Sangean

Sangean

Sangean DT-140 Manual de usuario

Sangean

Sangean PT-633 Manual de usuario

Sangean

Sangean PR-D18 Manual de usuario

Sangean

Sangean DT-120 Manual del propietario

Sangean

Sangean Pocket Radio R16 Manual de usuario

Sangean

Sangean PR-D3 Manual de usuario

Sangean

Sangean PR-D7 Manual de usuario

Sangean

Sangean WR-2 Manual de usuario

Sangean

Sangean SR-3 Manual de usuario

Sangean

Sangean DDR-66BT Manual de usuario

Sangean

Sangean HDR-18 Manual de usuario

Sangean

Sangean WR-3 Manual del propietario

Sangean

Sangean PT-633 Manual de usuario

Sangean

Sangean WFT-1 Manual de usuario

Sangean

Sangean DPR-2 Manual de usuario

Sangean

Sangean WR-11 Manual de usuario

Sangean

Sangean WFR-20 Manual de usuario

Sangean

Sangean DPR-35 Manual de usuario

Sangean

Sangean PR-D18 Manual de usuario

Sangean

Sangean DT-210L Manual de usuario

Sangean

Sangean WFR-1 - DATASHEET 3 Manual de usuario

Sangean

Sangean ProTravel PT-80 Manual de usuario

Sangean

Sangean DT-160CL Manual de usuario

Sangean

Sangean DT-120CL Manual de usuario

Manuales populares de Radio de otras marcas

EisSound

EisSound KBSound iSelect Manual de usuario

Midland

Midland 1001LWX Manual de usuario

Konig

Konig HAV-SR41 Manual de usuario

Roberts

Roberts exprssion Manual de usuario

VDigi

VDigi DD3.0 Manual de usuario

Radio Shack

Radio Shack 21-1863 Manual de usuario

Roberts

Roberts Stream 207 Manual de usuario

Sony

Sony Walkman SRF-M97 Manual de usuario

Stanley

Stanley FatMax FMC770 Manual de usuario

auna

auna DAB-Radio 10026947 Manual de usuario

SOUNDMASTER

SOUNDMASTER UR190 Manual de usuario

HYT

HYT TC-320 Manual de usuario

auna multimedia

auna multimedia Yellowstone 10026851 Manual de usuario

B-Tech

B-Tech GMRS-V2 Manual de usuario

Weierwei

Weierwei VEV-V8 Manual de usuario

SOUNDMASTER

SOUNDMASTER DAB750 Manual de usuario

Telefunken

Telefunken TF-1505 Manual de usuario

Makita

Makita LXRM03 Manual de usuario