Samsung SyncMaster 152 B Manual de usuario

http://www.samsung-monitor.com

http://www.samsungusa.com/monitor

BN68-00150D-01

SyncMaster 152B/152S/172B

Contents English

Safety Instructions

Unpacking Your Monitor

Setting up Your Monitor

Connecting Your Monitor

Self-Test Feature Check

Warning Messages

Environment

Useful Tips

SyncMaster 152B/152S

Adjusting Your Monitor

User Controls

Brightness

Contrast

Image Lock

Fine

Coarse

H-Position

V-Position

Reset

Geometry Reset

Color Reset

Color Temperature

Color Control

Language

Menu Position

H-Position

V-Position

Menu Display Time

Display Mode

Auto Adjustment

OSD Lock/Unlock

SyncMaster 172B

Adjusting Your Monitor

User Controls

Brightness

Contrast

Image Lock

Fine

Coarse

H-Position

V-Position

Reset

Geometry Reset

Color Reset

Color Temperature

Halftone

Language

Menu Position

H-Position

V-Position

Menu Display Time

Display Mode

Auto Adjustment

OSD Lock/Unlock

Power Saver

Troubleshooting

Specifications

Display Modes

Monitor and Stand

Power Cord

Signal Cable

Monitor Driver & Natural Color

(Not available in all locations)

Sound CablesMultimedia Speaker Stand

For Multimedia model (Option)

User’s Manual

DC-Adapter VESA Mounting Bracket

Unpacking Your Monitor

Safety Instructions

1. Do not use a damaged or loose plug.

2. Do not pull the plug out by the wire nor touch the plug with wet hands.

3. Use only a properly grounded plug and receptacle.

4. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

5. Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time.

6. Do not connect too many extension cords or plugs to an outlet.

7. Do not cover the vents on the monitor cabinet.

8. Put your monitor in a location with low humidity and a minimum of dust.

9. Do not drop the monitor when moving it.

10. Place the monitor on a flat and stable surface.

11. Set down the monitor carefully.

12. Do not place the monitor face down.

13. Do not spray detergent directly on the monitor.

14. Use the recommended detergent with a smooth cloth.

15. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.

16. Do not set a glass of water, chemicals or any small metal objects on the monitor.

17. Do not remove cover(or back). No user serviceable parts inside.

18. If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming

from it - unplug it immediately and contact an authorized deal-er or service.

19. Do not place any heavy objects on the monitor.

20. For each hour of looking at the monitor, you should let your eyes rest for 5 minutes.

21. Do not use or store inflammable substances near the monitor.

22. Do not try to move the monitor by pulling on the wire or the signal cable.

23. Do not move the monitor right or left by pulling only the wire or the signal cable.

24. Never insert anything metallic into the monitor openings.

Monitor and Stand

Setting up Your Monitor

Connecting Your Monitor

1. Connect the power cord for your monitor to the power port on the back of the monitor.

Plug the power cord for the monitor into a nearby outlet.

2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.

3. Connect the monitor to the Macintosh computer using the D-SUB connection cable.

4. In the case of an old model Macintosh, you need to connect the monitor

using a special Mac adaptor.

5. Turn on your computer and monitor. If your monitor displays an image, installation is complete.

Rear of Computer

New Model Macintosh

Old Model Macintosh

(Not included)

Adapter for Macintosh

Rear of Monitor

Setting up Your Monitor

Connecting Your Monitor

Setup-For Multimedia model

1. PC sound connection terminal (Input)

2. Headphone connection terminal (Output)

3. Volume

4. To listen in privacy, connect headphones here.

5. Connect a sound cable from the input source (sound card, computer, CD-ROM drive).

Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears

during normal operation if the video cable becomes disconnected or damaged.

4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.

If your monitor screen remains blank after using the previous procedure, check your video controller

and computer system; your monitor is functioning properly.

Setting up Your Monitor

Self-Test Feature Check

1. Turn off both your computer and the monitor.

2. Unplug the video cable from the back of the computer.

3. Turn on the monitor.

If the monitor is functioning properly, you will see a box with a border and text inside

as shown in the following illustration:

The three boxes inside the border are red, green and blue.

Your monitor provides a self test feature that allows you to check whether your monitor

is functioning properly.

Setting up Your Monitor

Warning Messages

If there is something wrong with the input signal, a message appears on the screen or the screen

goes blank although the power indicator LED is still on. The message may indicate that the

monitor is out of scan range or that you need to check the signal cable.

Environment

The location and the position of the monitor may influence the quality and other features of the monitor.

1. If there are any woofer speakers near the monitor, unplug and relocate the

woofer to another room.

2. Remove all electronic devices such as radios, fans, clocks and telephones that

are within 3 feet (one meter) of the monitor.

Useful Tips

A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC or

the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode

not supported, etc. In this case, first check the source of the problem, and then contact a service

center or your dealer.

Judging the monitor's working condition

If there is no image on the screen or an “Video mode not supported” message comes up,

disconnect the cable from the computer while the monitor is still powered on.

If there is a message coming up on the screen or if the screen goes white, this means the

monitor is in working condition.

In this case, check the computer for trouble.

Adjusting Your Monitor

Brightness

1. Push the Menu ( ) button.

2. Push the - button or + button until the

Contrast screen is displayed.

3. Push the Menu ( ) button to open the

Contrast adjustment screen.

4. Use the + button to increase the contrast or - button

to decrease the contrast.

Contrast

1. Push the Menu ( ) button.

2. Push the Menu ( ) button to open the

Brightness adjustment screen.

3. Use the + button to increase the brightness or - button

to decrease the brightness.

Direct Access Feature :

When OSD is not on the screen, Push the + or - button to

adjust brightness.

Adjust the Contrast.

Adjust the Brightness.

Adjusting Your Monitor

User Controls

1 2 3 4

1. Use this button to auto adjustment direct access.

2. Use this button to Exit the active menu or the OSD.

3. These buttons allow you to highlight and adjust items in the menu.

4. Use this button to open the OSD and activate a highlighted menu item.

SyncMaster 152B/152S

Adjusting Your Monitor

1. Push the Menu ( ) button.

2. Push the - button or + button until the H-Position screen

is displayed.

3. Push the Menu ( ) button to open the

H-Position adjustment screen.

4. Use the - and + buttons to change the horizontal position

of the monitor's viewing area.

Follow these instructions to change the horizontal

position of the monitor's entire display.

H-Position

1. Push the Menu ( ) button.

2. Push the - button or + button until the V-Position screen

is displayed.

3. Push the Menu ( ) button to open the

V-Position adjustment screen.

4. Use the - and + buttons to change the vertical position

of the monitor's viewing area.

Follow these instructions to change the vetical position

of the monitor's entire display.

V-Position

1. Push the Menu ( ) button.

2. Push the - button or + button until the Image Lock screen

is displayed.

3. Push the Menu ( ) button twice to open the

Fine adjustment screen.

4. Use the - or + buttons to remove any noise.

Adjusting Your Monitor

Image Lock is used to fine tune and get the best image by

removing noises that creates unstable images with jitters

and shimmers. If satisfactory results are not obtained using

the Fine adjustment, use the Coarse adjustment and then

use Fine again.

Image Lock

Fine

1. Push the Menu ( ) button.

2. Push the - button or + button until the Image Lock screen

is displayed.

3. Push the Menu ( ) button again and then

press the - or + button until the Coarse screen appears.

Push the Menu ( ) button to open the Coarse adjustment

screen.

4. Use the - or + buttons to remove any noise.

Image Lock is used to fine tune and get the best image by

removing noises that creates unstable images with jitters

and shimmers. If satisfactory results are not obtained using

the Fine adjustment, use the Coarse adjustment and then

use Fine again.

Coarse

Adjusting Your Monitor

1. Push the Menu ( ) button.

2. Push the - button or + button until the Color Temperature

screen is displayed.

3. Push the Menu ( ) button to open the

Color Temperature adjustment screen.

4. Press the - or + button to select User Adjusted,

Reddish or Bluish.

Color temperature is a measure of the "warmth"

of the image colors.

Color Temperature

1. Push the Menu ( ) button.

2. Push the - button or + button until the Color Control

screen is displayed.

3. Push the Menu ( ) button to open the Color Control

adjustment screen. Use the - or + button to select R(ed),

G(reen) or B(lue) and Push the Menu ( ) button.

4. Press the - or + button to adjust the color setting.

Follow these steps to adjust individual R, G, B

color control.

Color Control

1. Push the Menu ( ) button.

2. Push the - button or + button until the Languages screen

is displayed.

3. Push the Menu ( ) button to open the languages

selection screen.

4. Use the - button or + button to select the language

you would like to use.

Follow these steps to change the language used in the

menu. You can choose one of seven languages.

English, German, Spanish, French, Italian, Swedish, Russian.

Language

Note

The language chosen affects only the language of the OSD.

It has no effect on any software running on the computer.

Adjusting Your Monitor

1. Push the Menu ( ) button.

2. Push the - button or + button until the Reset screen

is displayed.

3. Push the Menu ( ) button twice to open the

Geometry Reset adjustment screen.

4. Push the + button to select Yes.

If you don't want to reset the monitor, use the - button to

select No.

Geometry parameters are replaced with the factory

default values.

Reset

Geometry Reset

1. Push the Menu ( ) button.

2. Push the - button or + button until the Reset screen

is displayed.

3. Push the Menu ( ) button again and then

press the - or + button until the Color Reset screen appears.

Push the Menu ( ) button to open the Color Reset

adjustment screen.

4. Push the + button to select Yes.

If you don't want to reset the monitor, use the - button to

select No.

Color parameters are replaced with the factory default

values.

Color Reset

Adjusting Your Monitor

1. Push the Menu ( ) button.

2. Push the - button or + button until the Menu Display Time

screen is displayed.

3. Push the Menu ( ) button to open the Menu Display Time

adjustment screen.

4. Use the - or + buttons to select 5, 10, 20, 50, 200 seconds.

20 seconds is the default value.

The menu will automatically turn off if no adjustments are

made for a certain time period.

You can set the amount of time the menu will wait before

it turns off.

Menu Display Time

1. Push the Menu ( ) button.

2. Push the - button or + button until the Display Mode

screen is displayed.

You can see the frequency, the polarity of the operational

signals and the resolution level.

Display Mode

Note

These screens do not allow any changes to the settings,

they are for information only.

Adjusting Your Monitor

1. Push the Menu ( ) button.

2. Push the - button or + button until the H-Menu Position

screen is displayed.

3. Push the Menu ( ) button twice to open the

H-Position adjustment screen.

4. Use the - and + buttons to place the menu in the

horizontal position you prefer.

You can change the horizontal position where the OSD menu

appears on your monitor.

Menu Position

H-Position

1. Push the Menu ( ) button.

2. Push the - button or + button until the V-Menu Position

screen is displayed.

3. Push the Menu ( ) button again and then press

the - or + button until the V-Position screen appears.

Push the Menu ( ) button to open the V-Position

adjustment screen.

4. Use the - and + buttons to place the menu in the

vertical position you prefer.

You can change the vertical position where the OSD menu

appears on your monitor.

V-Position

Adjusting Your Monitor

1. Push and hold in the Menu ( ) button for 5 seconds

or more to Lock the OSD.

2. Push and hold in the Menu ( ) button for 5 seconds

or more to Unlock the OSD.

OSD Lock/Unlock

1. Push the Auto button.

To make the automatic adjustment function sharper,

execute the 'AUTO' function while the AUTO PATTERN is on.

Auto adjustment allows the monitor to self-adjust to the

incoming video signal. The values of fine, coarse and

position are adjusted automatically.

Auto Adjustment User Controls

1 2 3 4

1. Use this button to auto adjustment direct access.

2. Use this button to Exit the active menu or the OSD.

3. These buttons allow you to highlight and adjust items in the menu.

4. Use this button to open the OSD and activate a highlighted menu item.

SyncMaster 172B

Otros manuales para SyncMaster 152 B

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Monitor de Samsung

Samsung

Samsung SyncMaster XL24 Manual de usuario

Samsung

Samsung C32G5 T Series Manual de usuario

Samsung

Samsung PS-42C67HD Manual de usuario

Samsung

Samsung UN32C5000QF Manual de usuario

Samsung

Samsung S27AG50 Series Manual de usuario

Samsung

Samsung SyncMaster 913BM Manual de usuario

Samsung

Samsung SyncMaster 700DX-3 Manual de usuario

Samsung

Samsung CF21G Series Manual de usuario

Samsung

Samsung SyncMaster 960HD Manual de usuario

Samsung

Samsung 1510MP Manual de usuario

Samsung

Samsung 460Pn - SyncMaster - 46" LCD Monitor Manual de usuario

Samsung

Samsung SyncMaster 940BW Plus Manual de usuario

Samsung

Samsung SyncMaster 750s Manual de usuario

Samsung

Samsung S22E310HY Manual de usuario

Samsung

Samsung 320BX Manual de usuario

Samsung

Samsung 942BW - SyncMaster - 19" LCD Monitor Manual de usuario

Samsung

Samsung 2233RZ - Syncmaster 22" 3D Gaming LCD Monito Manual de usuario

Samsung

Samsung S32R75 Q Series Manual de usuario

Samsung

Samsung LS27A650DS/ZA Manual de usuario

Samsung

Samsung STN-520WE Manual de usuario

Samsung

Samsung SyncMaster 2243DW Manual de usuario

Samsung

Samsung T240 - SyncMaster - 24" LCD Monitor Manual de usuario

Samsung

Samsung Flip WM55B Manual de usuario

Samsung

Samsung QM85F Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación