Samsung IAB Series Manual de usuario

LED R&D Lab(VD)

LED Display Install Manual

IAB Series

LH008IAB***

LH012IAB***

LH016IAB***

Ver. 0.9

LED R&D Lab(VD)

Revision History

Version Date (Y/M/D) Description

0.9 2022. 04. 23 P1.68 standard release

LED R&D Lab(VD)

1. Product and installation information

2. preparation of Cabinet installation

3. Wall Mount

4. FRAME installation and cable connection

5. Frame Bezel Installation

6. Dehumidification mode guide

7. IP Manual setting Guide

※ Appendix1 -LED Module and Circuit replacement method

※ Appendix2 –Update data when replacing TCON

※ Appendix3 –Gradation Calibration (SMC)

Table of contents

LED R&D Lab(VD)

Model Product appearance and information

IAB series

REMARK IAB Series : CoB Type / 120Hz Refresh Rate

1. Product and installation information

◆Model specification

-This manual is an installation manual for IAB and can be applied to the model below..

(Installation specifications for each pitch are the same)

LED R&D Lab(VD)

◆Model specification (IAB)

Specification

146” 110”

P0.84 (146”) P1.68 (146”) P1.26 (110”)

Cabinet

Siza

(mm)

Horizontal 3229.1 2422.7

Vertical 1826.1 1372.5

Pixels

Horizontal 3840 1920 1920

Vertical 2160 1080 1080

Module quantity 48 X 4, 192EA

weight

(Cabinet) 26.5kg 26.5kg TBD

SET weight 168kg TBD

Total weight 301kg TBD

Power consumption

(W) 1700(Max) / 1100(Typ)1240(Max) / 860(Typ)TBD

Luminance

(nit)

Max 500nit 500nit 500nit

Peak 1600nit 1400nit 1600nit

1. Product and installation information

LED R&D Lab(VD)

◆Cabinet information

1826.1

49.5

146”

3229.1

1372.5

49.5

110”

2422.7

1. Product and installation information

LED R&D Lab(VD)

◆Installation precautions (LED damage)

precautions Image

[External impact, fall caution]

1 Remove the cover-corner of the product before installation and do not

impact the LED surface or drop it on the floor.

2 Do not place the product on the vibrator and do not place the LED

surface facing the floor.

3 Make sure that the edge of the LED module is not damaged by external

contact.

4 Do not load more than 12 steps.

① ②

③ ④

[Watch out for LED damage caused by static electricity]

▶Do not work by touching the LED surface with hands without gloves.

[Caution of LED damage caused by metal]

▶Be careful not to get metal on the front of the LED.

▶When attaching the metal, separate the module and remove it using a

magnet.

MODULE

Front

metal

1. Product and installation information

LED R&D Lab(VD)

precautions Image

[Caution of LED damage caused by liquid]

When water or various chemicals touch the LED, the inside of the LED may be damaged.

①Water, dew, air conditioner condensate, sprayer, sweat, and saliva do not directly touch the

product.

-Be careful not to sweat on the product. (※ Maintain proper temperature so as not to sweat)

-Be careful not to spit on the product, and it is recommended to wear a mask.

②The following substances should not be directly in contact with the product, and

the case of exposure of the steam to the product should be minimized.

-Detergent or disinfectant : carpet cleaning detergent, glass cleaner, 84 disinfectant, etc.

(※ When cleaning the floor or wall with detergent or water, it is recommended to install a screen so that it does not touch the

product)

-Various chemicals: paints, mosquito repellents, cinnabar, benzene, toluene, solvents, surfactants, halogens (chlorine, bromine),

and substances containing these ingredients;

③If liquid touches the product

-If there is water on the product, turn off the product immediately, dry it enough for more than a day, and run the

dehumidification mode to remove moisture from the LED. (※ P74, refer to "Dehumidification mode using LSM")

-If there is any liquid other than water on it, remove it with alcohol and run the dehumidification mode.

[Precautions related to construction]

①In the case of installation at the construction site, the product must be installed after construction and

cleaning are completed.

②If the product is under construction in the installed space, take the following measures.

-Shielding film should be installed to protect the product by sealing the entire product so that it is not exposed to dust and

various liquids.

-Operates a video or 100 gray scale white for more than 2 hours every day.

-After the construction is completed, remove enough dust, various liquids, and steam, remove the shield, and execute the

dehumidification mode.

카펫

클리너 유리

세정제

Taping Shielding film

Disinfectant

※ Only use for IWA

◆Installation precautions (LED damage)

1. Product and installation information

◇Precautions for Appearance Washing

-It is recommended to wipe with a soft cleaning cloth provided with the

product, and to wash with a small amount of glass cleaning agent

provided with surfactant-based glass cleaning agent only if there is a

contaminated area that is not easily removed. (However, do not spray

glass cleaning agent directly on the screen)

-If there is hard dust on the surface during cleaning, there may be

damage to the surface film and LED, so remove the dust from the surface

and wash it.

★caution ★

1. Product and installation information

-Be careful of damage when cleaning with a gap between Half-Cabinet.

-Be careful of damage when cleaning between modules and modules in Half-Cabinet.

-Do not put cloth or other substances between the gaps or spray detergent directly.

-Do not sweep or wipe the LED surface with hard materials such as paper

towels, brushes such as combs and brushes, and sponges made of acrylic or

iron.

-Do not use chemicals such as wax, benzene, mosquito repellents, air fresheners,

lubricants, cleaning agents, etc. in products.

LED R&D Lab(VD)

◆Heat dissipation guide

Installation condition

-Conditions for using SAMSUNG WALL MOUNT

-Solar direct sunlight conditions cannot be installed (including glass window passage conditions)

-It is recommended to use room temperature below 25°C

-Effect of Cold/Hot Air Conditioning System

-When cold / hot air is the same air conditioning system,

∙Be careful not to let the warm air touch the product.

-Outside temperature measurement position

Measured at a distance of 300mm from the center of the product

Air vent aperture ratio

-use mesh type air vent

-If the aperture ratio is not 100%, the separation distance =

Minimum distance

aperture ratio(%) /100

-aperture ratio (%) =    .  ℎ

  

※ It is written based on Full white, back light 7

Video, created based on back light 10

wall

Outside

temperature

measurement

position

300mm

1. Product and installation information

Otros manuales para IAB Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Monitor de Samsung

Samsung

Samsung SyncMaster S22B310B Manual de usuario

Samsung

Samsung SyncMaster 172T Manual de usuario

Samsung

Samsung 2233RZ - Syncmaster 22" 3D Gaming LCD Monito Guía del usuario

Samsung

Samsung LU32J590UQU Manual de usuario

Samsung

Samsung 950B - SyncMaster 950 B Manual de usuario

Samsung

Samsung SyncMaster 743BM Manual de usuario

Samsung

Samsung CN17A series Manual de usuario

Samsung

Samsung STN-520WE Manual de usuario

Samsung

Samsung SAMTRON 76P Manual de usuario

Samsung

Samsung S24A600UCE Manual de usuario

Samsung

Samsung SyncMaster 2043BW Manual de usuario

Samsung

Samsung SyncMaster 731BA Manual de usuario

Samsung

Samsung SyncMaster 710VT Guía del usuario

Samsung

Samsung S22F380HY Manual de usuario

Samsung

Samsung SyncMaster 943AW Manual de usuario

Samsung

Samsung Samtron 98BDF Manual de usuario

Samsung

Samsung DM40E Manual de usuario

Samsung

Samsung SyncMaster S24A450BW Manual de usuario

Samsung

Samsung PPM 42H3 Manual de usuario

Samsung

Samsung SyncMaster 152 V Instrucciones de uso

Samsung

Samsung Odyssey S49CG954SU Manual de usuario

Samsung

Samsung SyncMaster 400MX-3 Manual de instalación y operación

Samsung

Samsung SyncMaster 172W Manual de usuario

Samsung

Samsung OH46D Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación