Samsung SP-R5200 Manual de usuario
SERVICE MANUAL
SAMSUNG SPR-5200
MODEL
CONTENTS
1. Product Specification
2. Operations & Installation
2-1 Checking Parts
2-2 Control Locations
2-3 Connecting Lines
2-4 Installing Handset Batteries
2-5 Charging the Handset
2-6 Using the Handset Carrying Clip
2-7 Turning the Handset On/Off
2-8 LCD Window Icon Descriptions
2-9 Choosing Dial Mode
2-10 Making a Call
2-11 Camp On Busy
2-12 Receiving a Call
2-13 Caller ID Display
2-14 Out of Range Indication
2-15 Battery Level Indicator
2-16 Adjusting Voice Volume
2-17 Choosing Ring Type
2-18 Adjusting Ring Volume
2-19 Key Lock
2-20 Memory Dialing
2-21 Call Log
2-22 Last Number Redial
2-23 Call Time Display On/Off
2-24 Key Beep On/Off
2-25 Base Number Display On/Off
2-26 Tone Dial Switchover
2-27 Setting Ring Delay Time
2-28 Changing Flash Time (Only for German Model)
2-29 Changing PIN (Personal Identification Number)
2-30 Registered Recall
2-31 Barring Calls
2-32 Reset
2-33 Registering New Handset with Base
2-34 Paging
2-35 Intercom Between Handsets
2-36 Call Transfer
2-37 Operating with Additional Base Unit
3. Exploded View & Parts List
3-1 SP-R5200 HANDSET P/L
3-2 SP-R5200 HANDSET Exploded View
3-3 SP-R5200 BASE P/L
3-4 SP-R5200 BASE Exploded View
3-5 SP-R5200 CHARGER P/L
3-6 SP-R5200 CHARGER Exploded View
3-7 SP-R5200 PACKING P/L
3-8 SP-R5200 PACKING Exploded View
4. Electrical Parts List
4-1 SP-R5200 Hand Logic Parts List
4-2 SP-R5200 Hand RF Parts List
4-3 SP-R5200 Base Logic Parts List
4-4 SP-R5200 Base RF Parts List
4-5 SP-R5200 Charger Part List
4-6 Service Subsidiary materials
4-7 PCB Array
5. Block Diagram
5-1 SP-R5200 Base Logic Block Diagram
5-2 SP-R5200 RF Block Diagram
5-3 SP-R5200 Hand Block Diagram
6. PCB Diagrams
7. Schematic Diagrams
7-1 SP-R5200 BASE
7-2 SP-R5200_CLIP CIRCUIT
7-3 SP-R5200 HAND
7-4 SP-R5200 RF
7-5 SP-R5200 CHARGER
8. Trouble Shooting
8-1 Trouble Shooting of Handset Logic
8-2 Trouble Shooting of Handset RF Module
8-3 Trouble Shooting of Baseset
8-4 Trouble Shooting of Baseset RF Part
9. Test Jig Usage
1. Product Specification
Product Specification 1-1
Item Description
Frequency Range 1881.792MHz~1897.344MHz
Channels 120 Duplex Channels
Channel Separation 1,728MHz
Carrier Power ²250mW (24dBm)
Modulation GFSK
Frequency Stability ² ± 50kHz
Standby Mode : 120hr
Operation Time Talk Mode : 12hr
Charging time : 15hr
Ambient Temperature Normal : 15ûC~35ûC
Extreme : 0ûC~40ûC
Humidity 0%~90%
Weight Baseset : 159.1g
Handset : 172.5g
Dimensions Baseset : 176✕91✕50
Handset : 156✕57✕27mm
Power Supply Baseset Input : DC 9V 400mA, DC 9V 150mA
Handset Input : 2.4V, 700mA (Ni-CAD)
Compliance TBR 6
TBR 10
2. Operations & Installstion
2-1 Checking Parts
Once you have unpacked your phone, check to make sure that you have all the parts shown below. If any piece
is missing or broken, please call your dealer.
2-1 Operations & Installation
Base
Adapter
Two AA Batteries
(Rechargeable Ni-Cd batteries) Service Manual
Line Cord
Handset
2-2 Control Locations
2-2-1 Handset
Operations & Installation 2-2
1
ABC
2
DEF
3
JKL
5
GHI
4
MNO
6
TUV
8
0
PQRS
7
WXYZ
9
C/R
INT
OK
Antenna
Earpiece
LCD window
Microphone
button
Makes, answers, or ends a call.
INT button
Activates intercom communications.
▲or ▼button
Scrolls through menus. Also adjusts volume.
C/R button
Clears characters from the display. Also performs a
switch-hook operation such as call waiting.
button
Confirms the selection. Also powers on/off.
button
Redials the last number you dialed. Also adds
a pause when storing a number in memory.
Rear
Charging
points
Battery cover
Carrying clip
Lamp
OK
2-2-2 Base
2-3 Operations & Installation
SP-R5200
Paging button
Allows you to page the handset.
Also used to register a new
handset with the base.
Line lamp
Blinks when a call comes in
and lights steadily when a call
is in progress.
LINE DC 9 V
Base Bottom
DC POWER
socket
Phone Line socket
2-3 Connecting Lines
1. Connect one end of the telephone line cord to the phone line socket on the bottom of the base unit, and the
other end to a standard phone wall jack.
2. Connect the modular end of the power adapter to the DC power socket on the bottom of the base unit, and
the other end to a standard AC wall outlet.
Operations & Installation 2-4
3. Route the cords through the recessed channel as shown.
DC 9 V
LINE
DC 9 V
LINE
To AC wall outlet To phone wall jack
2-4 Installing Handset Batteries
The handset uses the two AA size rechargeable Ni-MH or Ni-Cd batteries supplied.
1. Slide the battery cover in the direction of the arrow, then lift it off.
2-5 Operations & Installation
2. Remove old batteries if any, then insert new batteries observing correct polarity ( + , - ). Reversing the
orientation may damage the handset.
Operations & Installation 2-6
3. Replace the battery cover. Make sure that the cover is hooked in place.
4. Slide the cover up until it snaps shut.
Notes:
¥ The batteries need to be replaced if they do not recover their full storage capacity after recharging.
¥ When replacing batteries, always use good quality Ni-MH or Ni-Cd rechargeable AA size batteries.
Never use other batteries or conventional alkaline batteries.
Otros manuales para SP-R5200
1
Tabla de contenidos
Otros manuales de Teléfono inalámbrico de Samsung
Samsung
Samsung A820 Manual de usuario
Samsung
Samsung SP-R6100 Manual de usuario
Samsung
Samsung SMT-W6100 Manual de usuario
Samsung
Samsung SP-C900RSL Manual de usuario
Samsung
Samsung SP-R7000 Manual de usuario
Samsung
Samsung SPH-N350 Manual de usuario
Samsung
Samsung SP-R5200 Manual de usuario
Samsung
Samsung SMT-W5100 Manual de usuario
Samsung
Samsung DCS EURO SERIES 24 Manual de usuario
Samsung
Samsung SM-B105E Manual de usuario
Samsung
Samsung SP-R6100 Manual de usuario
Samsung
Samsung SMT-W5100E Manual de usuario
Samsung
Samsung SP-C501RSL Manual de usuario
Samsung
Samsung SCH-i201 Manual de usuario
Samsung
Samsung SMT-W6100 Manual de usuario
Samsung
Samsung SMT-W5100 Manual de usuario
Samsung
Samsung WIP-6000M Manual de usuario
Samsung
Samsung SP-R6100 Manual de usuario
Samsung
Samsung SP-R6150 Manual de usuario
Samsung
Samsung SP-R5100 Manual de usuario
