Samson AirLine 77 AH1N Manual de usuario
U H F WIRELESS S Y S TEM
•AH1/ Transmitter
•CR77 Receiver
OWNERS MANUAL
AH1 TRANSMITTER
ENGLISH
Introduction 3
QuickStart 4
Guided Tour - CR77 Receiver 6
Guided Tour - AH1 Transmitter 9
Setting Up and Using Your AirLine System 11
47
Channel Plan 49
FRANCAIS
Introduction 14
Prise en main 15
Visite guidée – Récepteur CR77 17
Visite guidée – Emetteur AH1 20
47
Tableau de conversion de fréquence 49
Copyright 2011, Samson Technologies Corp.
V5
Samson Technologies Corp.
45 Gilpin Avenue
Hauppauge, New York 11788-8816
Phone: 1-800-3-SAMSON (1-800-372-6766)
Fax: 631-784-2201
www.samsontech.com
Table of Contents
DEUTSCHE
Einleitung 25
Schneller Einstieg 26
Übersicht - Empfänger CR77 28
Übersicht - Sender AH1 31
Systeme 33
Technische Daten 47
Frequenzzuordnung der Empfangskanäle 49
ESPANOL
Introducción 36
Arranque rápido 37
Recorrido guiado – Receptor CR77 39
Recorrido guiado – Transmisor AH1 42
Ajuste y uso de su sistema AirLine 44
47
Tabla de conversión de frecuencias 49
Conguration et utilisation des systèmes AirLine 22
Welcome to Samson AirLine—the wireless system for the new millenium! Wireless microphone and instrument systems were originally
developed to eliminate cables, providing unparalleled freedom of movement. AirLine takes this concept to a new level with transmitters
so small, lightweight and aerodynamic, they are nearly invisible, providing a completely“hassle-free”user experience. To create the world’s
smallest wireless transmitters, we developed new proprietary technology. Featuring miniaturized circuitry and the ability to operate on
a single tiny AAA battery (with 14 hours typical battery life), these transmitters also feature signicantly improved wireless reception and
sound quality.
Samson AirLine systems operate in the N, U and E bands UHF frequency range and contains a CR77 true diversity receiver (for professional
performance applications) .The AirLine UHF System combines a feather-light AH1 headset transmitter with a Samson Q Series headset
microphone, ideal for tness and performance applications. The AirLine UHF Wind Instrument System combines the AH1 with a Samson
HM40 horn microphone. It is the rst wireless system designed for brass and reed instruments that eliminates the need for a body pack and
unwieldy microphone cables that limit your movement.
In this manual, you’ll nd a more detailed description of the features of all AirLine systems, as well as a guided tour through all components,
step-by-step instructions for setting up your system and full specications. If your AirLine system was purchased in the United States, you’ll
also nd a warranty card enclosed—don’t forget to ll it out and mail it! This will enable you to receive online technical support and will
allow us to send you updated information about this and other Samson products in the future. If your AirLine system was purchased out-
side of the U. S., contact your local distributor for warranty details. Also, be sure to check out our website (http://www.samsontech.com) for
complete information about our full product line.
SPECIAL NOTE for U.S. purchasers: Should your AirLine system ever require servicing, a Return Authorization number (RA) is necessary.
Without this number, the unit will not be accepted. If your AirLine system was purchased in the United States, please call Samson at 1-800-
372-6766 for a Return Authorization number prior to shipping your system. If possible, return the unit in its original carton and packing
materials. If your AirLine system was purchased outside of the U. S., contact your local distributor for information.
If you’ve had some prior experience using wireless systems, these QuickStart instructions will get you up and running with your AirLine sys-
Samson AirLine
Introduction
ENGLISH
tem in a matter of minutes! Detailed instructions for setting up and using your AirLine system can be found on page 14 of this manual, and
the “Guided Tour” sections on pages 4 - 13 provide full descriptions of all AirLine component controls and displays.
1. Make sure that the supplied receiver and AH1 transmitter are factory preset to the same channel.
2. Physically place the receiver where it will be used and extend its antenna(s) vertically.
3. Set the power switch on your UH1 transmitter to the “off” position (away from the arrow) and place a fresh battery in it. Then turn the
transmitter back on momentarily; its LED will flash once and then go off if the battery is sufficiently strong. Once battery strength is verified,
turn the transmitter off again.
4. If you are using an AH1 headset microphone, position it correctly as per the illustrations on page 12. If you are using an AirLine
UHF Wind Instrument System, clamp the horn mic to your instrument as described in the supplied HM40 owners manual.
5. Turn your audio system off and make the physical cable connection between the receiver’s balanced or unbalanced output jack (if nec-
essary, both can be used simultaneously) and a mic level audio input of your amplifier or mixer. If your system contains a CR77,be sure to set
its Audio Output Level switch correctly.
6. Turn the Volume, Level or AF Level knob on the receiver completely counterclockwise. Connect the supplied AC adapter to the receiver
and plug it in , but leave its power off for the moment.
7. Turn on the receiver. If your system contains a CR77 receiver, its “Power” LED will light steadily red.
Samson AirLine QuickStart
ENGLISH
4
8. Turn on your AH1 transmitter. If your system contains an AR1 receiver, its “Power/ RF” LED should change color from red to green, indicat-
ing that it is receiving valid RF signal and is placed and positioned correctly. If your system contains either a CR77 one of
the “A/B Receiver” LEDs will be lit, showing you whether the (left) “A” or (right) “B” receiver is currently being used. The CR77 meter will
also indicate the strength of the incoming RF signal.
9. Turn on your connected amplifier and/or mixer but keep its volume all the way down. Make sure the AH1 transmitter is unmuted. Set
the Volume, Level or AF Level knob on the receiver fully clockwise; this is unity gain.
10. Speak or sing into your headset microphone (or play the instrument connected to the horn microphone) at a normal performance level
while slowly raising the audio input control of your amplifier or mixer until the desired level is reached.
11. Do a walkaround through the intended area of coverage while observing the receiver’s “Power/RF” LED or RF Meter; it should indicate
sufficient RF reception in all areas of coverage. Reposition it (or its antenna) as necessary. If extended range coverage is required, a Samson
CR77 true diversity receiver (set to the same channel as the transmitter) should be used
12. If you hear any spurious noise from the receiver output when the transmitter is turned off, use the supplied plastic screwdriver to adjust
the receiver Squelch level control, slowly turning it clockwise to the point at which the noise disappears.
Samson AirLine
QuickStart
ENGLISH
5
1: Antennas (A and B) - The antenna
mountings allow full rotation for
optimum placement. In normal oper-
ation, both Antenna A (the antenna on
the left) and Antenna B (the antenna
on the right) should be placed in a
vertical position. Both antennas can
be folded inward for convenience
when transporting the CR77. See the
“Setting Up and Using the AirLine
System” section on page 14 in this
manual for information about antenna
installation and positioning.
2: Volume control - This knob sets
the level of the audio signal being
output through both the balanced and unbalanced output jacks on the rear panel (see #2 and #4 on page 6 in this manual). Reference level
is obtained when the knob is turned fully clockwise (to its “10” setting).
3: Audio Meter - - This “ladder” display (similar to the VU bar meter used on audio devices) indicates the strength of the incoming audio
signal. When the “0” segment is lit, the incoming signal is optimized at unity gain; when the “+6” segment is lit, the signal is overloading.
When only the left-most “-20” segment is lit, the incoming signal is at just 10% of optimum strength. If no segments are lit, little or no signal
is being received. See the “Setting Up and the AirLine System” section on page 14 in this manual for more information.
Samson AirLine Guided Tour - CR77 Receiver / Front Panel
ENGLISH
1
2
34
55
1
7
6
ANT. A ANT. B
VOLUME
POWER
RF METERAUDIO METER dB
0 10 25 50 75 1000 +3 +6-5-10-20
ANT. A ANT. B
SQUELCH
MIN
CR77 UHF TRUE DIVERSITY RECEIVER
MAX
6
4: Squelch control - This control determines the maximum range of the CR77 before audio signal dropout. Although it can be adjusted
using the supplied plastic screwdriver, it should normally be left at its factory setting. See the “Setting Up and Using the AirLine System”
section on page 14 in this manual for more information.
5: A/B Receiver LEDs - When signal is being received, one of these will be lit green, showing you whether the (left) “A” or (right) “B” receiver
is currently being used. The CR77 constantly scans its two antennas and automatically selects whichever is receiving the strongest, clearest
signal. This True Diversity switching is completely inaudible, but it effectively increases overall range while virtually eliminating potential
interference and phase cancellation problems.
6: RF (Radio Frequency) Level meter - This “ladder” display (similar to the VU bar meter used on audio devices) indicates the strength of
the incoming radio signal. When the “100%” segment is lit, the incoming RF signal is fully modulated and at optimum strength. When only
the second most left-most “10%” segment is lit, the incoming signal is at just 10% of optimum strength. If no segments are lit, little or no
signal is being received. See the “Setting Up and Using the AirLine System” section on page 14 in this manual for more information.
7: Power switch - Use this to turn the CR77 power on and off. When the receiver is on, the internal Power LED is lit.
Samson AirLine
Guided Tour - CR77 Receiver / Front Panel
ENGLISH
7
1: DC input - Connect the supplied 12
volt 160 mA power adapter here, using
the strain relief as shown in the illustra-
tion below. WARNING: Do not substi-
tute any other kind of power adapter;
doing so can cause severe damage to
the CR77 and will void your warranty.
2: Unbalanced output* - Use this
unbalanced high impedance (5K Ohm)
1/4" jack when connecting the CR77
to consumer (-10) audio equipment.
Wiring is as follows: tip hot, sleeve
ground.
3: Audio Output Level switch - Sets
the audio output level attenuation of
the balanced output (see #4 below) to
-20 dBm (line level) or -40 dBm (mic
level). See “Setting Up and Using the
AirLine System” on page 14.
4: Balanced output* - Use this elec-
tronically balanced low impedance (600
Ohm) XLR jack when connecting the CR77 to professional (+4) audio equipment. Pin wiring is as follows: Pin 1 ground, Pin 2 high (hot), and
Pin 3 low (cold).
* If required, both the unbalanced and balanced outputs can be used simultaneously.
Samson AirLine Guided Tour - CR77 Receiver / Rear Panel
ENGLISH
1
2
3
4
-
Using the strain relief: Gather up a loop of wire and pass it through the strain relief,
then pass the adapter plug through the loop in order to create a knot.
8
Guided Tour - AH1 Transmitter
Samson AirLine
1: Power / Battery LED - This LED flashes once when the AH1 is first turned on and lights steadily red when there is less than 2 hours of battery
power remaining, indicating that the battery needs to be changed.
2: Antenna - This permanently attached flexible antenna should be fully extended during normal operations. See the “Setting Up and Using the
AirLine System” section on page 14 in this manual for more information about antenna positioning.
3: Battery compartment - Insert a standard AAA alkaline battery here, being sure to observe the plus and minus polarity markings shown. We
recommend the Duracell type battery. Although rechargeable Ni-Cad batteries can be used, they do not supply adequate current for more than
four hours. WARNING: Do not insert the battery backwards; doing so can cause severe damage to the AH1 and will void your warranty.
+
_
ENGLISH
9
Samson AirLine
4: Mute switch - Move this switch in the direction of the arrow to mute the AH1; move it away from the arrow to unmute it and transmit
audio signal. Because the carrier signal remains during muting, no “pop” or “thud” will be heard. Note that turning this off does not turn
off the transmitter power—it is simply a way to temporarily mute the transmission of audio signal. If you don’t plan on using the AH1 for
extended periods, turn it off power by using the power on-off switch (see #5 below).
5: Power switch - Move this switch in the direction of the arrow to turn power to the AH1 on; move it away from the arrow to turn power
off. (to conserve battery power, be sure to turn the AH1 off when not in use). Be sure to mute the audio signal at your external mixer or
amplifier before turning the AH1 power on or off, or an audible pop may result.
Guided Tour - AH1 Transmitter
ENGLISH
10
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Sistema de micrófono de Samson
Samson
Samson Airline 77 Manual de usuario
Samson
Samson Concert 88 Manual de usuario
Samson
Samson AirLine Manual de usuario
Samson
Samson VHF Series Manual de usuario
Samson
Samson STAGE 5H Manual de usuario
Samson
Samson AirLine SYNTH AR300 Manual de usuario
Samson
Samson Concert 288x Manual de usuario
Samson
Samson Concert99 Manual de usuario
Samson
Samson CONCERT XD2 Manual de usuario
Samson
Samson AirLine Manual de usuario
Samson
Samson Stage v166 Manual de usuario
Samson
Samson AirLine 77 AH7 Manual de usuario
Samson
Samson S-Combine Manual de usuario
Samson
Samson Stage v266 Manual de usuario
Samson
Samson UHF Series One Manual de usuario
Samson
Samson AirLine Manual de usuario
Samson
Samson CONCERT SERIES IV Manual de usuario
Samson
Samson AirLine Manual de usuario
Samson
Samson XPD2m Manual de usuario
Samson
Samson Concert88 Manual de usuario
Manuales populares de Sistema de micrófono de otras marcas
Sennheiser
Sennheiser Evolution Wireless Digital EW-DX EM 2 Manual de usuario
Alpha Technologies
Alpha Technologies RBMS Manual de usuario
SWIT Electronics Co.,LTD.
SWIT Electronics Co.,LTD. CW-S150 Manual de usuario
Shure
Shure UA844 Manual de usuario
Panasonic
Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manual de usuario
Pyle
Pyle PDWM5000 Manual de usuario