Sam4s QPD-ML700 Manual de usuario
QPD-ML700
CUSTOMER DISPLAY
USER MANUAL
http://www.sam4s.com
- 1 -
Index
1. Safety Pre autions ...........................................................................................................................2
2. Environment Regulations .................................................................................................................3
3. Complete Produ t Configuration ....................................................................................................6
3.1 Name and Function of Each part.................................................................................................... 6
3.2 Interface ........................................................................................................................................6
3.3 Display Rotation ............................................................................................................................ 7
3.4 utton Operation ...........................................................................................................................7
4. Installation......................................................................................................................................... 8
4.1 Components ..................................................................................................................................8
4.2 Adjustment of Height .....................................................................................................................8
4.3 Installation Procedure ....................................................................................................................9
5. Produ t Spe ifi ations ..................................................................................................................... 12
6. Interfa e Spe ifi ation .....................................................................................................................14
6.1 Serial Cable Connection (Only for QPD-ML700S) .......................................................................... 14
6.2 US Cable Connection (Only for QPD-ML700U)............................................................................ 15
6.3 ETHERNET Cable Connection (Only for QPD-ML700E) ................................................................16
7. Control Command Spe ifi ations ....................................................................................................17
8. Display Mode.....................................................................................................................................19
9. Setup Mode ....................................................................................................................................... 20
10. Mass Storage Mode ........................................................................................................................ 22
11. USB Setup Mode ............................................................................................................................. 24
12. PC Utility.......................................................................................................................................... 25
13. About Image ....................................................................................................................................31
14. Firmware updates ........................................................................................................................... 31
- 2 -
1. Safety Pre autions
In using the present applian e, please keep the following safety regulations in order to prevent any
hazard or material damage.
WARNING
Violating following instru tions an ause serious injury or death.
- 3 -
2. Environment Regulations
RoHS (Restri tion of Hazardous Substan es)
WEEE (Waste Ele tri al and Ele troni )
Directive 2002/96/CE on the treatment, collection, recycling and disposal of electrical and
electronic devices and their components. The crossed dustbin symbol on the device
means that when it is to be disposed of, the device must be taken to the waste collection
centre for activation of the treatment, collection, recycling and disposal procedure.
- 4 -
Pre aution Statements
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential
hazards such as electrical shock.
Safety Pre autions
1. e sure that all built-in protective devices are
replaced. Restore any missing protective
shields.
2. When reinstalling the chassis and its
assemblies, be sure to restore all protective
devices, including nonmetallic control knobs
and compartment covers.
3. Make sure there are no cabinet openings
through which people - particularly children -
might insert fingers and contact dangerous
voltages. Such openings include
excessively wide cabinet ventilation slots and
improperly fitted covers and drawers.
4. Design Alteration Warning:
Never alter or add to the mechanical or
electrical design of the SET. Unauthorized
alterations might create a safety hazard. Also,
any design changes or additions will void the
manufacturer’s warranty.
5. Components, parts and wiring that appear to
have overheated or that are otherwise
damaged should be replaced with parts that
meet the original specifications. Always
determine the cause of damage or over-
heating, and correct any potential hazards.
6. Observe the original lead dress, especially
near the following areas : sharp edges, and
especially the AC and high voltage supplies.
Always inspect for pinched, out-of-place, or
frayed wiring. Do not change the spacing
between components and the printed circuit
board. Check the AC power cord for damage.
Make sure that leads and components do not
touch thermally hot parts.
7. Product Safety Notice:
Some electrical and mechanical parts have
special safety-related characteristics which
might not be obvious from visual inspection.
These safety features and the protection they
give might be lost if the replacement
component differs from the original - even if
the replacement is rated for higher voltage,
wattage, etc.
Components that are critical for safety are
indicated in the circuit diagram by shading, ( )
or ( ). Use replacement components that have
the same ratings, especially for flame resistance
and dielectric strength specifications. A
replacement part that does not have the same
safety characteristics as the original might create
shock, fire or other hazards.
SAFETY NOTICE : "For pluggable equipment, the socket-outlet shall be installed near
the equipment and shall be easily accessible."
- 5 -
Servi ing Pre autions
WARNING: First read the-Safety Precautions-section of this manual. If some unforeseen circumstance creates
a conflict between the servicing and safety precautions, always follow the safety precautions.
WARNING: An electrolytic capacitor installed with the wrong polarity might explode.
1. Servicing precautions are printed on the cabinet.
Follow them.
2. Always unplug the units AC/DC Adaptor from the
AC power source before attempting to:
(a) Remove or reinstall any component or
assembly
(b) Disconnect an electrical plug or connector
(c) Connect a test component in parallel with an
electrolytic capacitor
3. Some components are raised above the printed
circuit board for safety. An insulation tube or
tape is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.
4. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the portion around the
serviced part has not been damaged.
5. Check the insulation between the blades of the
AC plug and accessible conductive parts
(examples: metal panels and input terminals).
6. Insulation Checking Procedure:
Disconnect the power cord from the AC source
and turn the power switch ON. Connect an
insulation resistance meter (500V) to the blades
of AC plug.
The insulation resistance between each blade of
the AC plug and accessible conductive parts (see
above) should be greater than 1 mega ohm.
7. Never defeat any of the + voltage interlocks.
Do not apply AC power to the unit (or any of its
assemblies) unless all solid-state heat sinks are
correctly installed.
8. Always connect an instrument’s ground lead to
the instrument chassis ground before connecting
the positive lead ;
Always remove the instrument’s ground lead last.
Pre autions for Ele trostati ally Sensitive Devi es (ESDs)
1. Some semiconductor (solid state) devices are
easily damaged by static electricity. Such
components are called Electrostatically Sensitive
Devices (ESDs); examples include integrated
circuits and some field-effect transistors. The
following techniques will reduce the occurrence
of component damage caused by static
electricity.
2. Immediately before handling any semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known earth
ground. Alternatively, wear a discharging wrist-
strap device. ( e sure to remove it prior to
applying power - this is an electric shock
precaution.)
3. After removing an ESD-equipped assembly,
place it on a conductive surface such as
aluminium foil to prevent accumulation of
electrostatic charge.
4. Do not use freon-propelled chemicals. These
can generate electrical charges that damage
ESDs.
5. Use only a grounded-tip soldering iron when
soldering or unsoldering ESDs.
6. Use only an anti-static solder removal device.
Many solder removal devices are not rated as
anti-static; these can accumulate sufficient
electrical charge to damage ESDs.
7. Do not remove a replacement ESD from its
protective package until you are ready to install
it. Most replacement ESDs are packaged with
leads that are electrically shorted together by
conductive foam, aluminium foil or other
conductive materials.
8. Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.
9. Minimize body motions when handling
unpackaged replacement ESDs. Motions such
as brushing clothes together or lifting a foot
from a carpeted floor can generate enough
static electricity to damage an ESD.
- 6 -
3. Complete Produ t Configuration
3.1 Name and Fun tion of Ea h Part
3.2 Interfa e
I/F Type Stand Display Module
Serial Type
USB Type
Wi-Fi Type NO I/F
Ethernet Type NO I/F
- 7 -
3.3 Display Rotation
3.4 Button Operation
ESC(out of current function) / MENU(function adjustment)
SELECT(menu selection / change window mode)
UP button
DOWN button
POWER ON / OFF
- 8 -
4. Installation
4.1 Components
No.
Part Name Quan. Picture No.
Part Name Quan. Picture
⑤ Rubber Pad 4
① Display
Module 1
⑥ Rubber Cap 2
⑦
Screw
&
Anchor
3
② Stand 1
⑧ Adapter
(option) 1
③ Extension(L) 1
⑨ Cable
(option) 1
④ Extension(S)
2
⑩ User Manual
1
4.2 Adjustment of Height
Height 14cm 24cm 34cm 41cm 51cm
Extension(L) Χ Χ Χ 1 1
Extension(S) Χ 1 2 Χ 1
Product Image
QPD-ML700
CUSTOMER DISPLAY
USER MANUAL
http://www.sam4s.com
- 9 -
4.3 Installation Pro edure
■ Step 1
① Insert the connector into the Extension and
assemble the Display Module as shown in the
picture.
② The Pole Display can be adjusted to the five
type to use conveniently.
In case of assembling the Display Module with
the Extension or assembling the Extensions,
check the locking of hooks as shown in the
picture.
Tabla de contenidos
Otros manuales de Monitor de Sam4s
