Salto XS4 Mini Manual de usuario

USER MANUAL

XS4 CODE LOCKER

The XS4 Code Locker provides a convenient security solution for

many different lockers, cabinets, boxes etc. Achieve simple access

through the keypad, without the need for a network connection.

Codes can be assigned and can be active for a specied time

period. It is easy to install and can be programmed via your mobile

phone.

The battery pack, electronic components and the locking

mechanism are all located on the inside off the door to prevent

vandalism and sabotage.

www.saltosystems.com

Publications of SALTO SYSTEMS S.L. are protected by copyright and all rights are reserved.

SALTO SYSTEMS publications may not be reproduced in any form or by any means without written permission from the copyright owner

XS4 CODE LOCKER LK50

USER MANUAL - XS4 CODE LOCKER-ENG-04-22

CONTENT

1. Installation

2. Access

2.1 Fixed user PIN codes

2.2 Free assignment PIN codes

2.3 Timed PIN codes

2.3.1 Conguring timed PIN codes

3. Fixed user PIN codes management

3.1. Add xed PIN codes

3.2 Delete user PIN codes

4. Conguration

4.1 Service conguration menu

4.2 Factory reset

4.3 Clear all users

4.4 Change user conguration code

4.5 Change service conguration code

4.6 Special functions

4.7 Time and date conguration

4.8 Seed code

4.9 Enable web app conguration

5. Battery monitoring

6. Hardware factory reset

7. Technical specications

Page 3

Page 4

Page 5

Page 6

Page 7

Page 8

Page 9

Page 10

Page 11

Page 12

Page 13

Page 14

Page 15

USER MANUAL - XS4 CODE LOCKER-ENG-04-22

2.1. Fixed User PIN Codes

User PIN’s are allocated in the internal device memory. The XS4 Code Locker can retain up to

200 xed codes from 4 to 8 digits long. Each individual user has their own PIN code to

operate the locker. This permits also to share one locker between different users.

1234 is a default xed PIN code congured at position 1 under fabrication and can be used

to test the device. Check ‘Fixed User PIN Codes Management’ section on page 6 to manage

the xed PIN’s.

2. ACCESS

The keypad can grant access to open the locker in 3 different ways:

1. INSTALLATION

For instructions on the installation, please check the installation guide.

Please Note: When the lock is in silent mode there is no acoustic signal.

Check ‘Conguration’ section of the manual.

2 4

Example:

Upon entering a valid user PIN code,

conrmation beep will sound

and the green LED will blink one time.

The locker is ready to be opened or

closed.

Turn the knob to the left or the right.

Opening and Closing

0 0

Example:

In case of wrong code inserted, a

rejection beep will sound and the

Red LED will blink one time.

Wrong Code

USER MANUAL - XS4 CODE LOCKER-ENG-04-22

2.2. Free Assignment PIN Codes

Free assignment PIN code mode allows users to use any available locker just by using any

PIN code to capture the locker and use the same PIN code to open and release the locker.

Open and close by any 4 to 8 digits code. The code is erased every time the lock is opened,

making it available for a new user. Free Locker Mode must be enabled to use this function,

check ‘Conguration’ on page 11 section of this manual. Timed PIN codes are disabled when

Free Locker Mode is enabled.

0 0

Upon insert the same PIN used to

close the locker, conrmation will

sound and the Green LED will light up.

The locker is ready to be open.

Turn the knob to the right.

OPEN

Example:

0 0

When the lock is open, upon insert a

custom PIN code, conrmation beep

will sound and the Green LED will light

up. The locker is ready to be closed.

Turn the knob to the left.

Example:

USER MANUAL - XS4 CODE LOCKER-ENG-04-22

2.3. Timed PIN Codes

Open and close the lock with a 6 to 8 digits autogenerated timed code. When generating the

code, you will dene the period of time in which the code will be active.

NOTE: Timed PIN codes can only be enabled when Free Locker Mode is not active.

There are 2 different types of timed PIN codes that can be generated with a high security

algorithm (8 digits) or a standardised security algorithm (6 or 7 digits). These are:

2. Hour PIN code

Generated to grant access for 1, 2, 3 or 4 hours from the user dened start time.

2.3.1 Conguring Timed PIN Codes

If you want to congure the XS4 Code Locker manually, you will need to congurate both the

time, date and seed code to activate the timed PIN codes function. Please see the “Time and

Date conguration” and “Seed Code” sections on page 12 of this manual.

All required congurations are automatically performed if the device is congured with the

Web-Application instead of congured manually.

Timed PIN codes can be congured and generated on the Web Application and be shared via

mail or SMS. Check the Web Application manual for more details about timed PIN code genera-

tion.

1. Period PIN code

Grants access for a determined priode of time in days. The period can be from 1 to 28 days.

Period 0 grants access to the remaining hours at the current day up to 23:59.

0 0

1111

Upon inserting a valid PIN code, a conrmation beep will sound

and the green LED will light up.

The locker is ready to be open or closed.

Turn the knob to the left or the right.

OPEN and CLOSE

Example:

USER MANUAL - XS4 CODE LOCKER-ENG-04-22

3. FIXED USER PIN CODES MANAGEMENT

User codes can be changed, added, and deleted. Each user code is stored in a specic

addressed internal memory position (from 1 to 200). Each user code position must be kept

track of. Keep a record of the position number and the user name in the Web

Application or another registering tool. To add or delete user codes it is necessary to access

the User Conguration Menu:

Position User PIN

1 Carlos 148954

67 Torbjörn 94830132

179 Juan 1111

Exampel of user tracking:

The next sections uses Juan as example to add and delete xed PIN codes on the device.

Example:

7 1

Insert the User Conguration Code

(4711 is factory default)

A conrmation beep will sound and the

green LED will ash.

The keypad is ready to add or delete

xed user PIN’s.

User Conguration Menu

Enter:

USER MANUAL - XS4 CODE LOCKER-ENG-04-22

3.1 Add xed PIN codes

3.2 Delete user codes

To delete a single or more xed PIN code, it is not necessary to know the specic code,

however the postion of the code must be known.

All positions can be overwritten, so be aware to keep a

1 1

Example:

If a valid position is inserted, the Yellow LED will light solid,

and the green LED will blink until the xed user PIN code

is entered. The xed user PIN must be a number between

4 to 8 digits.

To add users, rst insert a position to place the new PIN

code (between 1 and 200).

A conrmation beep will sound and the yellow LED will

ash.

Enter: #

Insert 1 to start adding users.

Example:

If a valid position is inserted a conrmation beep will sound.

Insert the position of the PIN that you want to delete

(a number between 1 and 200).

A conrmation beep will sound and the red LED will ash.

Insert 2 to start deleting xed PIN codes from the device.

Deleting PIN codes

Enter:

Example:

USER MANUAL - XS4 CODE LOCKER-ENG-04-22

Once in Service Conguration Menu, the following actions can be performed:

4.1 Factory Reset

4.2 Clear All Users

4. CONFIGURATION

The service conguration code is used to authenticate and access the conguration menu,

which is needed to congure the Code Locker.

5 0

A conrmation beep will sound and all

LED’s will blink one time.

All the stored PIN codes are now

deleted.

Enter:

2 0

A conrmation beep will sound and all

LED’s will blink one time.

The keypad is automatically restarted

after a factory reset, and all LED’s will

blink once again at startup.

Enter:

Insert the Service Conguration Code

(12347890 is factory default)

A conrmation beep will sound and the

green LED will ash.

The keypad is now ready to be congured.

Service Conguration Menu

8 0

32 4

Enter:

USER MANUAL - XS4 CODE LOCKER-ENG-04-22

4.3 Change User Conguration Code

4.4 Change Service Conguration Code

Example:

Enter:

A conrmation beep will sound and the green LED will ash.

The Service Conguration Code has been changed.

8 0

32 4

A conrmation beep will sound and the yellow LED will ash until the

new Service Conguration Code is inserted again to conrm the action.

Insert the code again.

8 0

32 4

A conrmation beep will sound and the green LED will turn ON.

The keypad is ready to receive a new Service Conguration Code.

Insert a code that is between 4 to 8 digits.

3 1

A conrmation beep will sound and the green LED will

ash. The User Conguration Code has been changed.

A conrmation beep will sound and the red LED will light.

The keypad is ready to receive a new User Conguration

Code. Insert a code that is between 4 to 8 digits.

Example:

Enter:

USER MANUAL - XS4 CODE LOCKER-ENG-04-22

4.5 Special functions

Silent mode, audio advices can be

enabled or disabled.

A conrmation beep will sound and the yellow

LED will light.

The keypad is ready to ENABLE/DISABLE

the following special congurations. Enter the

number of the respective option to toggle the

Special Function’s state.

ON OFF

High Security, encryption to all auto-

generated timed PIN codes. With high

security encryption all timed PIN’s will

have 8 digits. Without high security

encryption timed PIN’s can be

between 6 to 7 digits.

Free Assignment Function, open and

close by any 4 to 8 digits code. The

code is erased every time the lock is

opened, making it available for a new

user.

#A conrmation beep will sound and the green LED will ash.

The Locker has been congured.

Enter:

Otros manuales para XS4 Mini

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cerrar de Salto

Salto

Salto Ei6***GD Series Instrucciones de funcionamiento y mantenimiento

Salto

Salto LE7S 7 Series Manual de usuario

Salto

Salto Ei75 Series Manual de usuario

Salto

Salto Clay IQ Manual de usuario

Salto

Salto Neoxx G4 Manual de usuario

Salto

Salto KPB22 Series Manual de usuario

Salto

Salto A i 650 Series Manual de usuario

Salto

Salto GEO GxE1 Series Manual de usuario

Salto

Salto XS4 Original+ E i 450 Series Manual de usuario

Salto

Salto AELEMENT Manual de usuario

Salto

Salto Geo Cylinder GxE Series Manual de usuario

Salto

Salto Neo Manual de usuario

Salto

Salto XS4 Geo Manual de usuario

Salto

Salto Aelement Manual de usuario

Salto

Salto SMILE Instrucciones de funcionamiento

Salto

Salto XS4-Locker Manual de usuario

Salto

Salto Node Manual de usuario

Salto

Salto Strike CEGD**IM series Manual de usuario

Salto

Salto XS4 Mini Manual de usuario

Salto

Salto Neo MIWA Manual de usuario

Salto

Salto Geo G P21 Series Manual de usuario

Salto

Salto XS4 Mini Manual de usuario

Salto

Salto Geo Padlock P3 Manual de usuario

Salto

Salto XS4 Mini Manual de usuario

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Kwikset

Kwikset 48334/01 Manual de usuario