Sainlogic WS-0310 Manual de usuario

SAINLOGIC WS-0310 Professional WIFI

Weather Station User Manual

1.Introduction

Thank you for your purchase of the WS0310 Professional WIFI

Wireless Weather station. The following user guide provides step by

step instructions for installation, operation and troubleshooting.

2.Warnings

Warning: Any metal object may attract a lightning strike, including

your weather station mounting pole. Never install the weather station in

a storm.

Warning: Installing your weather station in a high location may

result in injury or death. Perform as much of the initial check out and

operation.

3.Getting Started

The WS0310 weather station consists of a display console (receiver), a

sensor array with Integrated Outdoor Transmitter and mounting

hardware.

3.1. Parts List

The WS0310 weather station consists of the following parts (as

referenced in Figure 1 ).

QTY

Item

Image

Display Console

(LxHxW):8.3X1.0X6.1 in

LCD Dimensions (LxW): 6.7 x

4.9 in

QTY

Item

Image

Integrated Outdoor Transmitter

Dimensions (LxHxW)：

13 x 6 x 11in

Anemometer Mounting Bracket

(with pole insert)

Dimensions: 3 x 4 x 1 ½”

Anemometer Mounting Bracket

Back Plate (pole mount)

Dimensions: 3 x 3 x 1 ”

Anemometer Pole

Dimensions: 12 x 1½ x 1”

Pole mounting nuts (M3) / bolts

Ø3)

QTY

Item

Image

Pole mounting nuts (M5) / bolts

( Ø5)

Tapping screws

Manual

Power Adapter

Figure 1

3.2 Recommend Tools

●Precision screwdriver (for small Phillips screws)

●Compass or GPS (for wind direction calibration)

●Adjustable Wrench

3.3 Sensor Assembly Set Up

The following illustration shows the full segment for Thermo-Hygrometer

，WIND,RAIN and UV INDEX sensor.purposes only ,as shown in

Figure 2.

Figure 2

3.3.1 Insert batteries into the transmitter. Locate the battery

door on the transmitter, push and open the battery compartment, as

show in Figure 3.

Figure 3

Remove the battery door on the back of the sensor by removing the set

screw, as shown in Figure 4.

Figure 4

Inserting 3xAA batteries in the battery compartment, as show in Figure

Figure 5

Close the battery door. Make sure the gasket (around the battery

compartment) is properly seated in its trace prior to closing the door.

Tighten the set screw.

Note: Do not install the batteries backwards. You can permanently

damage the sensors. The solar panel does not charge the batteries, so

rechargeable batteries are not needed or recommended.

Note: We recommend installing Lithium AA batteries for sensors.

The sensor LED indicator will light for 3 seconds, and then flash once

per 16 seconds thereafter. Each time it flashes, the sensor is

transmitting data.

Replace the battery door and push to tighten it.

Note: If the sensor does not power up after inserting the batteries,

press the reset button shown in Figure 6.

Figure 6

3.4 Display Console

3.4.1 Display Console Layout

The display console layout is shown in Figure 7

Note: The following illustration shows the full segment LCD display

for description purposes only and will not appear like this during normal

operation.

Figure 7

1. Outdoor temperature display

2. WIFI network

3. Outdoor humidity display

4. Outdoor humidity HI/LO alarm icon

5. Min/Max reset for 24h icon

6. Weather forecast

7.Rainfall display(RATE, 24h,

WEEK,MONTH, TOTAL)

8. Rainfall units of measure

9. Date display

10. Time alarm icon

11. Time and Year

12. UV Index display

13. Sunshine intensity

14. MOON phase

15. Sunlight units of measure

16. Indoor Dew point display

17. Indoor Dew point ICON

18. Indoor temperature and humidity display

19. Pressure (REL and ABS) display

20. Pressure units of measure

21. Wind speed average display

22.Wind gust display

23.Wind speed units of measure

24.Wind chill and feels like HI/Lo alarm icon

25. Wind direction

26. OUT dew point and AT(Apparent

Temperature) display icon

27. Integrated outdoor transmitter Low power

indicator

28.Temperature units (°F or °C)

29.Outdoor temperature HI/LO alarm icon

3.4.2 Display Console Set Up

It is recommended to plug in the power supply to reduce the

battery consumption and extend the service life.

Note: The sensor array must be powered and updating before

powering up the console, or the

console will time out searching for the sensor. Power the console last.

Make certain the weather station sensor array is at least 10’ away from

the console and within

100’ of the console. If the weather station is too close or too far away, it

may not receive a proper signal.

Remove the battery door on the back of the display, as shown in Figure

8. Insert three AAA (alkaline or lithium) batteries in the back of the

display console. The display will beep once and all of the LCD

segments will light up for a few seconds to verify all segments are

operating properly.

Note: The character contrast is best from a slightly elevated viewing

angle.

Figure 8

Replace the battery door, and fold out the desk stand and place the

console in the upright position.

The unit will instantly display indoor temperature, humidity, pressure,

tendency, moon phase, and time. The wind speed, wind gust, wind

direction, rain, UV/Sunlight , Integrated outdoor temperature and

humidity will update on the display within a few minutes. Do not Press

any menu buttons until the outside transmitter report in, otherwise the

outdoor sensor search mode will be terminated. When the outdoor

transmitter data has been received, the console will automatically

switch to the normal mode from which all further settings can be

performed.

While in the search mode, the remote search icon will be constantly

displayed.

If it does not update, please reference the troubleshooting guide in

Section 18.

Note: The power adapter is intended to be correctly oriented in a

vertical or floor mounted position. The prongs are not designed to hold

the plug in place if it is plugged into a ceiling, under-the-table or cabinet

outlet.

Figure 9

Note: If the power adapter is plugged in, BL ON will display in the

time area for three seconds when powered up. Conversely, if the power

adapter is not plugged in, AC OFF will be displayed, the icon will

display .

4.Weather Station Installation

4.1 Pre Installation Checkout Before installing your weather

station in the permanent location, we recommend operating the

weather station for one week in a temporary location with easy

access. This will allow you to check out all of the functions, insure

proper operation, and familiarize you with the weather station and

calibration procedures. This will also allow you to test the wireless

range of the weather station.

4.2 Site Survey

Perform a site survey before installing the weather station. Consider the

following:

1. You must clean the rain gauge once per year and change the

batteries every two years. Provide easy access to the weather station.

2. Avoid radiant heat transfer from buildings and structures. In general,

install the sensor array at least 5’ from any building, structure, ground,

or roof top.

3. Avoid wind and rain obstructions. The rule of thumb is to install the

sensor array at least four times the distance of the height of the tallest

obstruction. For example, if the building is 20’ tall, install 4 x (20 – 6)’ =

56’ away. Use common sense. If the weather station is installed next to

a tall building, the wind and rain will not be accurate.

4. Wireless Range. The radio communication between receiver and

transmitter in an open field can reach a distance of up to 300ft,

providing there are no interfering obstacles such as buildings, trees,

vehicles, high voltage lines. Wireless signals will not penetrate metal

buildings. Most applications will only reach 100ft due to building

obstructions, walls and interference.

5. Radio interference such as PCs, radios or TV sets can, in the worst

case, entirely cut off radio communication. Please take this into

consideration when choosing console or mounting locations.

Tabla de contenidos

Otros manuales de Estación meteorológica de Sainlogic

Sainlogic

Sainlogic SC089 Manual de usuario

Sainlogic

Sainlogic FT0366 Manual de usuario

Sainlogic

Sainlogic FT0360 Manual de usuario

Sainlogic

Sainlogic FT0835 Manual de usuario

Sainlogic

Sainlogic WS0835 Manual de usuario

Sainlogic

Sainlogic FT-0310 Manual de usuario

Sainlogic

Sainlogic WS-0835 Plus Professional Manual de usuario

Sainlogic

Sainlogic WS0835 Manual de usuario

Sainlogic

Sainlogic FT0300 Manual de usuario

Sainlogic

Sainlogic FT0073 Manual de usuario

Manuales populares de Estación meteorológica de otras marcas

Auriol

Auriol AHFL 433 A1 Manual de usuario

NexSens

NexSens G2-HYDROMET Manual de usuario

Hyundai

Hyundai WS 2202 Manual de usuario

IROX

IROX HBVR761 UV-X Manual de usuario

La Crosse Technology

La Crosse Technology C86371 Manual de usuario

ADE

ADE WS 1711 Manual de usuario

Auriol

Auriol z29592 Manual de usuario

Auriol

Auriol 296289 Manual de usuario

Hyundai

Hyundai WS 2266 Manual de usuario

La Crosse Technology

La Crosse Technology WS-2210 Manual de usuario

La Crosse Technology

La Crosse Technology WS-811561 Manual de usuario

Ventus

Ventus W177 Manual de usuario

National Geographic

National Geographic VA Colour RC Manual de usuario

Renkforce

Renkforce 1208067 Manual de usuario

Levenhuk

Levenhuk Discovery Report WA40 Manual de usuario

Instant Transmission

Instant Transmission MA 10410 Manual de usuario

Lutron Electronics

Lutron Electronics PHB-318 Manual de usuario

WAREMA

WAREMA EWFS Weather station eco Manual de usuario