Safe Fleet DH4 Manual de usuario
© Safe Fleet | 2020 | All rights reserved | Part #: 700-1234 R1
Installation Guide
DH4
4-Channel Hybrid DVR
© Safe Fleet | 2020 | All rights reserved | Part #: 700-1234 R1
— this page intentionally blank —
© Safe Fleet | 2020 | All rights reserved | Part #: 700-1234 R1
DH4 Installation Guide
Table of Contents
System Components. . . . . . . . . . . . . . 4
Required Tools & Equipment.. . . . . . . 4
System Diagram.. . . . . . . . . . . . . . . . . 5
DH4 Installation. . . . . . . . . . . . . . . . . . 6
Installation Best Practices.. . . . . . . . . . . . . . . . . . . .6
Installing the DVR. . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installing the Adapter Harness (Optional). . . . . . .8
Installing the Expansion Harness (Optional). . . . .8
Firmware Updates. . . . . . . . . . . . . . . . . . . . . . . . . . .9
Hardware Installation Checklist. . . . . . . . . . . . . . .10
DH4 Operation. . . . . . . . . . . . . . . . . . 11
DVR Front Panel Features. . . . . . . . . . . . . . . . . . . .11
DVR Back Panel Features. . . . . . . . . . . . . . . . . . . .12
Video System Status. . . . . . . . . . . . . . . . . . . . . . . .13
Video Flagging.. . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Using On-screen Keyboards. . . . . . . . . . . . . . . . . .14
Health Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
DH4 Administration . . . . . . . . . . . . .16
Accessing the On-screen Display.. . . . . . . . . . . . .16
Working with Video.. . . . . . . . . . . . . . . . . . . . . . . . .19
. . . . . . . . .22
Setting up the DVR. . . . . . . . . . . . . . . . . . . . . . . . . .22
Time/Date Tab.. . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Title/Display Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Camera Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . .27
. . . . . . . . . . . . . . . . . . . . . . . . .28
Alarm Settings.. . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
. . . . . . . . . . . . . . . . . .32
. . . . .34
. . . . . . . . . . . . . .34
Network Settings.. . . . . . . . . . . . . . . . . . . . . . . . . . .36
Advanced Network Settings. . . . . . . . . . . . . . . . . .38
Built-in WIFI Settings. . . . . . . . . . . . . . . . . . . . . . . .40
VMS Servers.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
G-Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Speed Settings.. . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
GPS Fencing.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
User Levels.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
System Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Monitor Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Appendix.. . . . . . . . . . . . . . . . . . . . . . 50
Need Help?.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Contact Safe Fleet Technical Support.. . . . . . . . .50
Returns. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Warranty And End-User License Agreement. . . .50
© Safe Fleet | 2020 | All rights reserved | Part #: 700-1234 R1
DH4 Installation Guide
p. 4
System Components
Required Tools & Equipment
The DVR system must be installed by a professional installer. A professional installer has the experience and equipment to
Check that you have all the system components and inspect the units for any scratches or damage before installing.
Keys included in package contents:
• DVR keys for securing the removable hard drive.
• Front cover keys for securing the removable front cover.
•
•
System Components
The typical installation components are listed below.
• DH4 video recorder with hard drive, locking front cover, cable cover, fasteners, and mounting plate
• Power harness (PH2X2MFJR)
Camera Options
•
•
• Camera harness (HEHDxx or HExHD)
Accessory Options
• Adaptor harness (WT2)
• G-Sensor (G-SENSOR-EXT)
• Expansion harness
• RGY button with extension cable
• GPS antenna (built-in GPS)
• WIFI antenna (built-in WIFI)
• Smart-Reach WIFI bridge
• Smart-Reach cellular router
• Portable video monitor
• SD card
© Safe Fleet | 2020 | All rights reserved | Part #: 700-1234 R1
DH4 Installation Guide
p. 5
System Diagram
System Diagram
Power harness/fuse pkg.:
PH2X2MFJR
Harness WT2 supports
RGY button and extn.
harness pkg. HEDM20
20 ft./6.1m
power harness: 060-1104
20 ft./6.1m RGY extn.
harness: 060-1197
(optional): 065-1010
20 ft./6.1m
3 wires
1A
10A
POWER
Black - Battery Negative
Yellow - Vehicle Ign +12V
Red - Vehicle +12V
4 Standard Resolution and/or
High Denition Cameras
Adapter
Harness*3
5 wires
RGY BUTTON
1x5 Microt
SIGNALS
Black - Left Turn
Green - Stop
Red - Brake Signal
Brown - Warning
White - Right Turn
G-SENSOR
(optional):
Rear Vision System (Optional)
Reserved
2x3 Microt
1x4 Microt
Typical System Setup
© Safe Fleet | 2020 | All rights reserved | Part #: 700-1234 R1
DH4 Installation Guide
p. 6
DH4 Installation
DH4 Installation
Installation Best Practices
Before you begin, keep in mind that it is your responsibility to avoid damaging safety or electrical systems. If you are not
The following table outlines the physical and environmental requirements for installing a DH4 DVR:
VENTILATION Install the DVR away from any sort of heat outlet, heater, or AC blower. Do not operate the DVR
in a closed-in area, or restrict ventilation in any way. The DVR requires air circulation to maintain
optimum operation temperature and provide best performance. Do not expose the DVR to
moisture!
SURFACE Do not mount the DVR to a plastic panel or other surface that is subject to constant vibration.
ORIENTATION Mount the DVR in either a horizontal or vertical orientation, or hung right side up, but NOT
upside down.
CLEARANCE
removal of the security front cover and easy access to the hard drive and USB ports. Allow
power cables.
MOUNTING CABLES The radius for the mounting cables will be dictated by the cable cover. The rear-most surface
of the cable cover will be about 3 inches from the back of the DVR to allow camera cables to
bend over each other.
ETHERNET CABLES Avoid right angle bends in the Ethernet cables.
POWER CABLES Provide enough slack on the power cable to prevent any force from being exerted on the
WARNING
It is your responsibility to avoid damaging safety or electrical systems. Ensure you read and understand the DH4 DVR
Installation Requirements.
If you are not condent in your ability to perform the procedures in this tutorial, please contact Technical Support at
1.844.899.7366 or PTsupport@safeeet.net.
© Safe Fleet | 2020 | All rights reserved | Part #: 700-1234 R1
DH4 Installation Guide
p. 7
DH4 Installation
Installing the DVR
The DVR typically ships with the locking front cover, mounting plate, and cable cover off, but in the shipping box. The hard
disk drive is in a separate box in the system shipping kit.
To install the DVR:
1. Select an appropriate mounting location and orientation:
horizontal or vertical.
2. Insert a hard drive in the DVR.
3. Insert the key into the hard drive lock and rotate a
quarter turn to lock the drive.
4. Use the mounting plate to mark the desired position of
the DVR and drill the four mounting holes.
5. Fasten the mounting plate to the mounting surface with
the four self-drilling screws.
6. Slide the rear bottom edge of the DVR into the spring tab
on the back edge of the mounting tray.
7. Attach the front bottom edge to the front of the DVR
using the two pan-head Phillips screws.
8. Connect the necessary cables and components.
9. Attach the cable cover to the DVR using the thumb
screws provided.
10. When DVR installation is complete, attach the front door
by hooking the door along the top edge and turning the
key to the locked position.
© Safe Fleet | 2020 | All rights reserved | Part #: 700-1234 R1
DH4 Installation Guide
p. 8
DH4 Installation
Installing the Adapter Harness (Optional)
The Adapter Harness (Part # WT2) connects the DVR to Signal inputs and the optional RGY button.
Installing the Expansion Harness (Optional)
The Expansion Harness (Part # 060-1059) can connect the DH4 DVR to Student Tracking and Rear Vision systems.
To install the Adapter Harness:
1.
the DVR rear panel SIGNALS socket.
2. Connect the 5 signal input wires.
3.
button extension harness (optional).
For more information, see the System Diagram on
page 5.
To install the Expansion Harness:
1.
EXPANSION socket on the DVR.
2.
Tracking harness (optional).
3.
System harness (optional).
To DVR SIGNALS
socket (2 x 6)
To Signal inputs
(5 wires)
To RGY Button
extn. harness (1 x 5)
Unused
To DVR EXPANSION
socket (2 x 4)
To Rear Vision System
(optional)
To Student Tracking
harness (optional)
Reserved for future use
© Safe Fleet | 2020 | All rights reserved | Part #: 700-1234 R1
DH4 Installation Guide
p. 9
DH4 Installation
To update the Firmware version:
1. Power up the DVR using the vehicle ignition.
2.
3. After the DVR starts up, right-click in the On-screen Display
and select
Conguration -> System -> Program Update
4. In the Program Update tab, click Update
window appears.
5. Click Yes to proceed or No to cancel. Yes starts the
complete.
6.
7. Remove the USB memory device.
Completing Upgrade
After restarting, the DVR may take up to 3 minutes to load and complete the upgrade. Wait until the DVR nishes
loading.
Firmware Updates
menus, see DH4 Administration: Accessing the On-Screen Display.
Firmware Updates
Only install rmware updates as directed by Technical Support.
© Safe Fleet | 2020 | All rights reserved | Part #: 700-1234 R1
DH4 Installation Guide
p. 10
DH4 Installation
HARNESSES (CAMERA, RECORDER, AND ACCESSORIES)
Ensure cables and harnesses are properly secured.
Check that sharp metal edges are not touching cables or harnesses.
Ensure connections are solid (no shorts).
CAMERAS
Ensure tight mounting.
Examine the internal harness connections and ensure they are solid.
Ensure the lid is properly seated on the gasket and secured tightly.
DVR
Ensure tight mounting.
Check that all connections are tight.
SYSTEM
Install fuses.
Plug portable video monitor into DVR, and power up the DVR from the vehicle ignition.
Test audio/video record and playback.
Reformat the hard drives by navigating to Main Menu System Program Update Format.
A warning message tells you all data will be erased. Click Yes. When the process completes and a message appears,
click OK
Fasten and lock the front cover. Secure the cable cover on the DVR using the screws provided.
Hardware Installation Checklist
Tabla de contenidos
Otros manuales de DVR de Safe Fleet
