S2Konnect N-3010AVB Manual de usuario
S2Konnect N-3010AVB
S2Konnect N-3010AVB
10/100/1000Base-T Adapter
PCI Express
User Manual
2
S2Konnect N-3010AVB
3
Copyright © S2Konnect GmbH, 2010. All rights reserved.
This manual refers to the S2Konnect N-3010AVB 10/100/1000Base-T Adapter with AVB ,
PCI Express x1, 1 x RJ-45.
Contents are subject to change without notice.
Product and brand names are (registered) trademarks of their appropriate owners.
If you have comments on this documentation, please send to:
S2Konnect GmbH
Siemensstrasse 23
76275 Ettlingen / Germany
visit our web site: http://www.s2konnect.com
S2Konnect N-3010AVB
4
Conventions
The following conventions apply to this manual.
Warnings and Notes
Used to indicate a potentially hazardous situation which, if not avoided, could result in death
or serious injury. Example: dangerous voltage.
Used to indicate a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury. Example: electrostatic discharge.
Used for additional information and advice.
!
i
S2Konnect N-3010AVB
5
Table of Contents
Conventions 4
Warning Notes 4
Safety Precautions 7
Avoiding injuries - Avoiding damage 7
1 Introduction 8
2 System requirements 8
3 Installation of the Network Adapter 8
4 Connection of the Network Adapter 10
Transmission Distances 10
Connection to the Network 10
5 Hardware Features 11
Adapter Characteristics 11
LED Displays 12
6 Software Features 13
Operating System Support 13
High Performance 13
TCP, UDP and IP Checksum Calculation 13
Jumbo Frames 13
TCP Segmentation (Large Send Off-Load) 13
Dynamic Interrupt Moderation 13
Promiscuous Mode / Multicast Support 14
Alert Standard Format (ASF) 14
PXE / RPL Support 14
Boot Agent ROM 14
Advanced Power Management / Wake on LAN 15
Reliability 15
Link Aggregation 15
Redundant Switch Failover 16
Hot-Plug 16
Parity 17
User Diagnostics (DOS and Windows) 17
Marvell Network Control (Windows) 17
Virtual LAN (VLAN) Support 18
7 Troubleshooting 19
8 Important Information 20
Technical Support 20
Returning an Adapter for Repair 20
Additional Documentation and Updates 20
Technical Specications 21
Appendix A. License and Warranty Information 24
The Americas, Asia, Australia, New Zealand, Pacic 24
Europe 25
Deutschland, Schweiz, Österreich, Lichtenstein 26
S2Konnect N-3010AVB
Table of Figures
Figure 1: Insertion of the adapter into the computer
Figure 2: Connection of the RJ-45 cable/plug
Figure 3: Location of the LEDs
Figure 4: Typical display after a successful test (external repeater)
6
S2Konnect N-3010AVB
7
Safety Precautions
To protect yourself from injuries and avoid damage of the device, always observe the following
safety instructions when installing the network adapter.
Avoiding injuries
Electrical current!
Electrical current from power, phone, and communications cables can be hazardous.
Never touch any electrical elements with bare hands.
To avoid potential shock hazards:
• Do not carry out any installation, maintenance, or (re)conguration work during a
thunderstorm.
• Do not connect or disconnect any power cables during a thunderstorm.
• For installation into systems which are supporting Hot-Plug and will be not disconnected
from electrical power system read the relevant documentation rst.
• Do not connect the network adapter to a telephone line.
Electrical installations must comply with the safety regulations of the country in which they are
operated.
Avoiding damage
Electrostatic discharge!
Electrostatic discharge may damage or destroy the Network adapter.
To avoid damaging the S2Konnect N-3010AVB Network adapter observe the following:
• Switch off the computer.
• Disconnect the power cord from the power outlet.
• Remove the computer cover.
• Before installing the network adapter, put on an antistatic wrist strap (electrically conduc-
tive).
• Connect the wrist strap to the computer chassis
Do not connect the wrist straps to the ground terminal of the power supply!
Faulty wiring could make this terminal live and potentially lethal.
• When you are ready to install the network adapter, open the antistatic bag.
• Hold the antistatic packaging of the network adapter against the bracket of an expansion
slot on your computer for at least two seconds.
This reduces the static charge in the packaging and in your body.
If you need to place the network adapter somewehre after removing it from the antistatic
bag, make sure you place it on the antistatic bag and on a level surface.
Do not place the network adapter on the computer cover or on any other metal surface.
• Cautiously insert the adapter into the corresponding slot.
Do not touch any circuits on the network adapter or any of its port contacts.
In general, observe the following:
• Never use force when working with the network adapter or the PCI Express bus.
• Do not allow anyone else to touch the network adapter.
• Avoid unnecessary movement since this can increase electrostatic charge.
!
i
S2Konnect N-3010AVB
8
Introduction
Thank you for purchasing a S2Konnect product.
This document describes the installation of the network adapter card.
The N-3010AVB is a PCI Express adapter which must be installed in a PCI Express slot of the com-
puter.
The adapter contains a Network chipset “Marvell 88E8059“
System requirements
Computer System:
The N-3010AVB adapter is a typical desktop adapter supporting high throughput of data.
You may utilize this adapter in any system supporting PCI Express bus with one Lane (PCIe x1).
Cable:
You must use minimum a Category 5 unshielded twisted pair cable for 100 MB/s or Gigabit
(1000 MB/s) transfer rates.
1
2
Installation of the S2Konnect N-3010AVB
Network Adapter
The installation procedure in Hot-Plug systems may differ from the following. For Hot-Plug sys-
tems, read the corresponding documentation. Have the computer manual ready and if necessary,
a key and screwdriver to open the cover and remove the bracket.
To install the adapter in the computer, proceed as follows:
1. Switch off the computer in wich the network adapter is to be installed.
2. Disconnect the power cord from the power outlet.
Observe the safety instructions (see page 7).
3. Open the computer cover as described in your computer manual.
You may need a screwdriver or similar tool to remove the screws from the cover.
If you are installing a network adapter in a tower computer, we recommend to put the com-
puter on its side in order to apply the correct force to insert the adapter into the PCI Express slot.
4. Consult the section in your computer manual that describes how to install expansion cards.
5. Locate a free PCI Express slot on the motherboard.
S2Konnect PCI Express adapters can be installed in x1, x4, x8 and x16 slots.
6. Remove the bracket from the expansion slot (if applicable).
Follow the instruction in your computer manual.
7. Remove the network adapter from the antistatic bag.
Observe the safety instructions (see page 7).
8. Insert the network adapter into the PCI Express slot as described in your computer manual
(also see gure 1 “Insertion of the adapter into the computer“).
Make sure the network adapter is correctly aligned with the PCI Express slot on the motherboard.
9. Push the network adapter down vertically into the slot until it is rmly seated.
10. If available, tighten the locking screw on the xing bracket until the adapter is rmly connec-
ted to the computer cover (or to the attachment provided for expansion cards).
11. Replace the computer cover.
12. Replace and tighten all screws.
13. Reconnect the power supply.
Observe the safety instructions (see page 7).
3
i
S2Konnect N-3010AVB
9
Figure 1. Insertion of the adapter into the computer
S2Konnect N-3010AVB
10
Connection of the Network Adapter
This chapter describes the physical connection of the S2Konnect N-3010AVB Network Adapter to
a network.
Transmission Distances
The maximum transmission distance for the S2Konnect N-3010AVB 10/100/1000Base-T adapter,
is 100m, you have to use a Category 5 unshielded twisted pair cable or better.
Connection to the Network
Observe the safety instructions given on page 7.
In order to connect the adapter to the network, proceed as follows:
1. If necessary, congure the port on the switch to which the network adapter is to be
connected (also see the switch manual).
2. If possible, disconnect the switch and the computer from the power supply.
3. At one end of the cable connect the RJ-45 connector to the port on the switch.
4. At the other end of the cable connect the connector to the port on the network adapter.
(see gure 2. “Connection of the RJ-45 cable/plug“).
The port type (e.g. 1000Base-T) on the network device and that on the switch must be
identical.
4
Figure 2. Connection of the RJ-45 cable/plug
ACT/LINK
10=OFF
100=GRN
1000=YLW
Tabla de contenidos
Otros manuales de Adaptador de S2Konnect
