Ryobi HBG620 Manual de operación
HBG620
4
1 2
3
1
1
7
7
6
5
8
9
2
2
10
7
3
4 5
6 7
6
9
5
10 10 3
230V,50Hz
250W
2850min-1
Ø150x20xØ12.7mm
8.5kg
BENCH ATTACHMENT (Fig. 3)
1. Fasten grinder to work bench before operating this machine.
There is a bench attachment hole(6) on either side of the base
which should be used to secure the grinder.(Fig.3)
2. 2 x 10mm diameter bolts should be used to secure the grinder
to the bench or stand.
AUTO ON LIGHT (Fig. 4)
GLOBE REPLACEMENT
COOLANT TRAY (Fig. 5)
OPERATION
EYESHIELD ADJUSTMENT
TOOL RESTS ADJUSTMENT
CHANGING THE GRINDING WHEELS
Your RYOBI bench grinder comes complete with an auto on
adjustable light (9) which allows you to illuminate the grinding
wheels and workpiece when operating in dark areas. The light will
automatically come on when the grinder is switched on. When
grinder is not in use, switch off the tool to avoid overheating of the
lamp.
When the globe is worn out and will no longer work gently remove
the bulb from the holder by pushing in and turning anticlockwise.
Use only RYOBI genuine replacement part 12 volt, 21 watt globe.
To replace gently push the globe into the insert and turn clockwise.
IMPORTANT: Do not use force as this could lead to the globe
breaking and serious injury.
The in-built coolant storage dip tray (5) allows you to cool
overheated workpieces. Simply pull out the tray and half fill with
appropriate coolant.
NOTE: The height and angle of eyeshields can be adjusted up and
down to the user's riquirement.
Voltage
Power input
No load speed
Disc size
Net weight
1. Spark breaker
2. Eye shield
3. Grinding wheel
4. ON/OFF switch
5. Coolant tray
6. Bench attachment hole
7. Tool rest
8. Opti eye shield
9. 12V Light
10. Wheel dressing tool
7
2
ASSEMBLY (Fig. 1, 2 )
WHEEL DRESSING TOOL (Fig. 6, 7)
After extensive use, the grinding wheels (3) will accumulate
in-ground metal build up. To clean the wheels detach the wheel
dressing tool (10) from the storage holder (Fig.6)
Rest the wheel dressing tool (10) on the tool rest approx. 5mm
from the grinding wheel (2). Switch on the grinder and wait a few
seconds until the grinding wheel reaches full revolution then
slowly move the dressing tool to gently touch against the
grinding wheel holding firmly with two fingers. Do not use
excessive pressure. (Fig.7)
CAUTION: Do not allow the grinding wheel and dressing tool to
touch before the grinding wheel has reached high speed as this
may cause the dressing tool to be flicked from your grasp
causing serious injury.
To ensure safety and reliability, all repairs should be
performed by an AUTHORIZED SERVICE CENTER or
other QUALIFIED SERVICE ORGANIZATION.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
WARNING!
After use, check the tool to make sure that it is in top
condition. It is recommended that you take this tool to a
RYOBI Authorized Service Center for a thorough cleaning
and lubrication at least once a year.
DO NOT MAKE ANY ADJUSTMENTS WHILE THE
MOTOR IS IN MOTION.
ALWAYS DISCONNECT THE POWER CORD FROM THE
RECEPTACLE BEFORE CHANGING REMOVABLE OR
EXPENDABLE PARTS (BLADE, BIT, SANDING PAPER
ETC.), LUBRICATING OR WORKING ON THE UNIT.
MAINTENANCE
Tabla de contenidos
Otros manuales de Amoladora de Ryobi
Ryobi
Ryobi RA-DG14-B Manual de usuario
Ryobi
Ryobi AG454 Manual de usuario
Ryobi
Ryobi AG4031G Manual de usuario
Ryobi
Ryobi P421 Manual de usuario
Ryobi
Ryobi RSS280 Manual de usuario
Ryobi
Ryobi EAG75100 Manual de usuario
Ryobi
Ryobi EAG95100 Manual de operación
Ryobi
Ryobi PCL445 Manual de usuario
Ryobi
Ryobi P421 Manual de usuario
Ryobi
Ryobi RBGL650G Manual de usuario
Ryobi
Ryobi BGH616 Manual de usuario
Ryobi
Ryobi R18SS4 Manual de usuario
Ryobi
Ryobi EAG95100RG Manual de operación
Ryobi
Ryobi RBG6G Manual de usuario
Ryobi
Ryobi RSS200 Manual de usuario
Ryobi
Ryobi EAG750RB Manual de usuario
Ryobi
Ryobi HBGL650 Instrucciones de uso
Ryobi
Ryobi AG451 Manual de usuario
Ryobi
Ryobi G-2240 Manual de operación
Ryobi
Ryobi EAG-7511 Manual de usuario
