Ruckus Wireless SmartZone 300 Manual de usuario
Ruckus SmartZone 300
Spare Hard Disk Drive
Quick Setup Guide for
SmartZone 5.1
This Quick Setup Guide provides basic instructions for
ordering and installing a spare hard disk drive (HDD) into
the Ruckus SmartZone 300 (SZ300) controller.
For information on advanced conguration and
management options, see the Getting Started Guide and
other appropriate documents, which are available for
download from the Ruckus Support website:
https://support.ruckuswireless.com/documents.
This Guide in Other Languages
请从以下网站获得该指南的简体中文版 https://
support.ruckuswireless.com.
Vous trouverez la version française de ce guide à
l'adresse suivante https://support.ruckuswireless.com.
このガイドの日本語版は https://
support.ruckuswireless.com でご覧ください。
이 가이드의 한국어 버전은 웹 사이트 (https://
support.ruckuswireless.com) 에서 확인하시기 바랍니다.
Veja a versão em português (Brasil) deste guia em
https://support.ruckuswireless.com.
Puede ver la versión en español (América Latina) de esta
guía en https://support.ruckuswireless.com.
Hard Disk Drive Ordering Information
To order a spare hard disk drive for the SmartZone 300
controller, contact Ruckus Support.
For information on how to contact Ruckus Support, visit
https://support.ruckuswireless.com/contact-us. When
asked for the part number, provide the information in the
following table.
Part Number Description
902-S350-0000 Kit, Spare (FRU), hard disk drive, SZ300
Opening the Front Bezel
The front bezel helps prevent accidental access to the
controller's modules. Before you can install a module,
you must open the front bezel.
NOTE: If the controller is mounted in a rack with
adjacent units below the unit where a module needs to
be serviced, Ruckus recommends extracting the
controller from the rack approximately 5cm (2 in.). This
will provide clearance of the bezel when rotated out
towards you.
Follow these steps to open the front bezel.
1. With the controller in front of you, place your ngers
on both sides of the front bezel.
2. Pull the bezel toward you until it opens.
3. Gently lower the bezel to expose the controller's
replaceable modules.
FIGURE 1 Controller with the front bezel open
Installing a Spare Hard Disk Drive
After you have obtained a spare hard disk drive and
opened the front bezel of the SmartZone 300 controller,
you are ready to install the drive.
NOTE: Both hard disk drives (HDDs) are redundant and
hot-swappable. You do not need to power o the
controller to swap a single failed HDD.
Follow these steps to install the hard disk drive.
1. On the front panel, identify the HDD that you want to
replace. From the top of the front panel, disk tray 1 is
for a solid state drive (SSD), and disk trays 2 and 3 are
for HDDs (see the following gure).
NOTE: Tray 4 is unused.
FIGURE 2 Disk trays on the front panel of the controller
NOTE: If you are replacing a failed disk, check the
LED of each tray. A red or amber LED indicates that
the disk is not operational.
2. Unlock the disk tray by moving the orange disk tray
lock to the left (unlock) position.
3. Press the black/blue tray button to open the tray
handle.
Copyright © 2018 ARRIS Enterprises LLC. All rights reserved. Page 1 of 2
Published November 2018, Part Number 800-71882-001 Rev A
FIGURE 3 An open disk tray
4. Hold the tray handle, and rmly pull it toward you
until the disk tray, along with the HDD, comes out of
the chassis completely. Put the disk tray assembly
aside.
5. Unpack the replacement HDD. The replacement HDD
comes assembled with its own disk tray.
6. Insert the disk tray (with the replacement HDD) into
the disk bay until the drive locks in the connector on
the SAS backplane.
7. Close the handle, and lock the tray by moving the
orange disk tray lock to the right (lock) position.
8. Verify that the new drive's status LED ashes green.
This indicates that the controller is rebuilding the
RAID array.
When the controller completes rebuilding the RAID
array, the drive's status LED shows solid green.
You have completed replacing a spare HDD in the
SmartZone 300 controller.
Closing the Front Bezel
After you complete installing a module, remember to
close the front bezel to prevent access to the modules
and protect them from dust and dirt.
If the controller is mounted in a rack, before completing
the following steps, grab the side handles on the
controller, and push the controller back into the rack.
Secure the controller to the rack using the rack fasteners.
Perform the following steps to close the front bezel.
1. With the controller in front of you, gently lift the bezel
and push it back onto the front panel of the
controller.
2. Gently press the bezel against the front panel until it
clicks into place.
The bezel should now be ush against the front
panel, completely covering it.
© 2018 ARRIS Enterprises LLC. All rights reserved.
ARRIS, the ARRIS logo, Ruckus, Ruckus Wireless, the Ruckus logo, and
the Big Dog design are trademarks of ARRIS International plc and/or
its aliates. All other trademarks are the property of their respective
owners.
Copyright © 2018 ARRIS Enterprises LLC. All rights reserved. Page 2 of 2
Published November 2018, Part Number 800-71882-001 Rev A
Otros manuales para SmartZone 300
10
Otros manuales de Almacenamiento de Ruckus Wireless
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario