Rubine IA Series Manual de usuario
16 pages Qty : 5000 bks - RM 0.40
12 pages Qty : 5000 bks - RM 0.35
5. Do not attempt to repair the heater without qualified technician.
8. Test water temperature with hand before using the shower.
2. Do not install the heater where there is consistent spray directly over the unit.
11. Do not leave the hand shower idle in the pail.
(For Inverter Silent Pump Model &
AC Pump Model Only)
(Model IA9100DC – Inverter Silent Pump)
(Model IA9200AC – AC Pump)
2. CHROME ACCESSORIES
560mm
45mm
65mm
680mm
35 mm
Φ
32 mm
Φ
1/2
19 mm
Φ
32 mm G
Φ
3. RAIN SHOWER SET
6
3
5.00 mm
6
5
0.00 mm
Water Saver
Chip
Water Saver
Chip
Tighten the
Slide down
and hook
the
assembled
divider to
the
mounted
square
bracket
1
2
STEP 1
There is two Water Saver Chips located
under the hand showerand on top of the
rain shower head.
Water Saver Chip
A chip that helps you save water up tp 50%!
ALERT
You may remove the two water saver chips if
prefer stronger water pressure. Please be
reminded that this is up to personal
preference.
STEP 2
Do marking for the location of the lower square and upper
round bracket. Install the bracket holders on the wall.
Assemble the upper tube with rain shower and lower tube
with divider.
Slide down and hook the assembled divider to the
mounted square bracket.
Tighten the screws and make sure all joints are completely
connected to avoid leakage.
Rain Shower Head
360 Degrees 3-in -1 Rotation Diverter
360˚
180˚
90˚270˚
5
Diverter
- optional
6
2
7
2. INLET and OUTLET connection of the heater unit
should not be reversed, with stop valve installed on
INLET. (Diagram 1)
a) Connect the stop valve to INLET, and be sure to
put a gasket to prevent water leakage,
(Diagram 3)
INLET
Diagram 3
Stop Valve
Inlet
Outlet
correct installation
stop
valve
Inlet
Outlet
inlet - outlet reverse
(wrong installation)
stop
valve
Inlet Outlet
stop valve reverse
(wrong installation)
SAFETY PRECAUTION
Do not install reverse INLET and OUTLET of heater
ON MAX
OFF STEP 2
STEP 1
8
Restore cover
Diagram 4
Diagram 5
c) Restore the cover and secure screw at the bottom. (Diagram 4)
(Diagram 5)
9
10
a) Remove the filter mesh at the stop valve (for filter type only) by turning the knob filter
counter clockwise direction and pull out the knob (Diagram 6). Flush it with water to
remove any trapped sediments. Install the knob filter back to its original position.
stop valve
Diagram 6
CLEAN
REGULARLY
(Diagram 6)
AC Pump 2.0kg
440(H) x 190(W) x 75(D)
Otros manuales para IA Series
1
Otros manuales de Calentador de agua de Rubine
Rubine
Rubine RSH-M30L Manual de usuario
Rubine
Rubine IA Series Manual de usuario
Rubine
Rubine CUBO Series Manual de usuario
Rubine
Rubine IA991D Manual de usuario
Rubine
Rubine SSE SERIES Manual de usuario
Rubine
Rubine BENE 10FE Manual de programación
Rubine
Rubine CETUS Series Manual de usuario
Rubine
Rubine SSE SERIES Manual de usuario
Rubine
Rubine FLUSSO Series Manual de usuario
Rubine
Rubine FORTE Series Manual de usuario
