RS PRO 137-2292 Manual de usuario
LCD DESOLDERING STATION
Instruction Manual
EN
137-2292
Description
137-2292 is designed for lead free desoldering. The quick heat-up and strong
vacuum are suitable for all types of DIP components.
Robust design, single hand operation and strong suction provide easy
removal of the residual solder from the single-sided or double sided PCBs.
1.Control Unit
The desoldering gun is micro-processor controlled. The digital control electronics,
high-quality sensor and heat exchange system guarantee precise temperature
control at the soldering tip.
2.Desoldering Iron gun
The 90W Desoldering iron gun along with a wide spectrum of soldering tips
can be used anywhere in the electronics field.
The high power and gun design make this iron suitable for fine desoldering
work. The heating element is made of ceramic and the sensor on the tip can
control temperature quickly and accurately.
LCD DESOLDERING STATION/English
Technical Specification
Model No.
Plug Type
Voltage(ACV)
Soldering Power
Power Consumption
Temperature
Vacuum Pressure
Heating Element
Accessories
Certificate
Station Size (mm)
Weight (kgs)
137-2292
220V-240V~ 50Hz
90 W
140 W
160°C ~ 480°C
>600mm Hg
Ceramic Heater
Spare tip x 3 (Ø1.2(on the gun) / Ø1.0 / Ø1.5mm) Cleaning tool x 3
(Ø0.7 / Ø0.9 / Ø1.2mm)Filter sponge x 4 (Ø20.8x1 +Ø16.8x3)
CE, RoHS
172 x 135 x 190
1.6
1
EU F Schuko UK G type
31.07.2020, Versions-Nr. 002
Operating Instruction
1 .Place the desoldering gun in the separate holder. Then connect the plug to
the receptacle on the station and turn clockwise to tighten the plug nut.
Check that the power supply is corresponding to the specification on the type
plate and the power switch is in the “OFF” position. Connect the control unit
to the power supply and switch on the power. A self-test will be carried out in
whichall display elements are switched on briefly. The electronic system then
switches on automatically to the set temperature and the value is displayed.
2 .The display and temperature setting
LCD DESOLDERING STATION/English
①.Shows the actual temperature of the desoldering tip.
②.Shows the setting temperature: Pressing the “UP” or “DOWN” button can
switch the digital display to the set point display. The set-point can be changed
by ±1℃by tapping the “UP” or “DOWN” button. Press and hold the button to
change the set-point quickly. The digital display will return automatically to
the actual value and the iron will reach the setting temperature automatically.
③.℃/℉display: Switching the temperature display from ℃to ℉by pressing
the “ * ”button and then the electronic system will display the actual
temperature①and setting temperature②in ℉, and vice versa.
④.When the actual temperature on the desoldering tip is less than the set-point,
“HEAT ON” will display and make the desoldering tip heat up.
⑤.When the absolute offset is more than ±10℃between the actual temperature
and the set-point on the desoldering tip or the nozzle, “WAIT” will display.
This means that the temperature control system is not in a stable state,wait
a moment to let the “WAIT” disappear.
⑥.When “-----” & “ERROR” displays, there may be a problem with the system,
or the desoldering iron gun is not connected to the control system correctly.
2
31.07.2020, Versions-Nr. 002
31.07.2020, Versions-Nr. 002
LCD DESOLDERING STATION/English
Safety Instruction
1. The manufacturer assumes no liability for uses other than those described in
the operating instructions or for unauthorized alterations.
2. The operating instructions and cautions should be read carefully and kept in
an easily accessible location in the vicinity of the control system. Failure to
observe the cautions will result in accidents, injury or risks to health.
Caution
1. The power cord only can be used in approved power sockets or adapters.
2. High Temperature
The temperature of the desoldering tip can reach as high as around 400℃
(752℉) when the power switch is on. Since mishandling may lead to burns
and fire, be sure to comply with the following precautions:
A. Do not touch metallic parts near the desoldering tip/ nozzle.
B. Do not use this system near flammable items.
C. Advise other people in the work area that the unit can reach a very high
temperature and should be considered potentially dangerous.
D. Turn off the power switch while not in use .
E. Before replacing parts or storing the system, turn off the power and let it
cool down to the room temperature.
F. Warning: this tool must be placed on its stand when not in use.
G. Fire may result if the appliance is not used with care, therefore:
a) Be careful when using the appliance in places where there is combustible
material.
b) Do not apply to the same place for a long time.
c) Do not use in presence of an explosive atmosphere.
d) Be aware heat may be conducted to combustible materials are out of sight.
e) Place the appliance on its stand after use and allow it to cool down
before storage.
f) Do not leave the appliance unattended when it is switched on.
3.Take care of your tools
3.1 Do not use the tools for any applications other than desoldering.
3.2 Do not tap the iron against the work bench or otherwise subject the iron to
severe shocks.
3.3 Do not file the desoldering tip to remove the oxide, please wipe the tip on the
cleaning sponge.
3.4 Use only accessories or attachments which are listed in the operation manual.
3.5 Use of other tools and other accessories can lead to injury.
3.6 Please turn off the power before connecting or disconnecting the desoldering
gun.
3
31.07.2020, Versions-Nr. 002
LCD DESOLDERING STATION/English
4. Maintenance
4.1 Before use, safety devices or damaged parts must be carefully checked
for error-free and intended operation.
4.2 Inspect moving parts to ensure they don’t bind,and there is no damage to
the parts.
4.3 Damaged parts must be repaired or replaced by a qualified technician,so
long as nothing else is indicated in the operation manual.
4.4
Use only accessories or attachments which are listed in the operation manual.
Use of other tools and other accessories can lead to a danger of injury.
5. Keep children at a distance
Warning: this appliance is not intended for use by young children and
infirm persons unless they have been adequately supervised by a
responsible person to ensure that they can use the appliance safely.
Warning: Young children should be supervised to ensure that they do not
play with the appliance.
When not in use the station should be stored in a dry location which is out of
the reach of children. Switch off the desoldering station when not in use.
6. Work environment
Do not use the desoldering station in a moist or wet environment.
The desoldering gun should be placed on the holder after finished using.
7. Observe the valid safety regulations at your work place.
4
Desoldering Gun Maintenance
LCD DESOLDERING STATION/English
31.07.2020, Versions-Nr. 002
1. To avoid injury or damage; do not touch metallic parts near the nozzle, do not
use this system near flammable items.
1. Ensure power is off and unplugged before performing any maintenance
procedure, except during the cleaning process of the nozzle and heating element.
3. If the pump does not operate, immediately clean the nozzle & heating element,
and replace the filter
4. At high temperatures, the solder waste will become oxidized (lead free solder’s
melting point is 220°C, non-lead-free solder’s melting point is 180°C), swelled
and stuck tightly on the inner wall. If it is not cleaned after use, the solder waste
will block the desoldering gun and will not be able to be removed even with
cleaning pin.
1. After each operation is finished, immediately trigger the gun to activate the
vacuum pump in free air 3-5 times, this can clean the older waste from inside
the pipe.
2. If used for more than 20 minutes continuously repeat 1. Along with using the
cleaning tool.
3. When you find the desoldering efficiency gets down, please use the cleaning
pin to clean the pipe immediately.
4. If the operation interval is long, we advise to adjust the temperature to about
200°C. When you use it again, you can adjust to the working temperature.
5. When the glass tube has absorbed about 1/2 solder waste, please clean it
immediately. When you find the filter is getting hardened, please replace the
filter immediately.
5
Warnings
Instructions
(Cleaning pin)
LCD DESOLDERING STATION/English
Remove solder waste
1. Pull the lever up “A” and the holder “B”
BPull
A1. up
31.07.2020, Versions-Nr. 002 6
Troubleshooting
Fault
Failure cause
Solution
LCD - No display Fail to connect power
source
Check the power cord connection and
plug in the power cord to power Jack.
Fuse blown
Replace fuse: 3.15A / 250V
Cannot melt solder Unreasonable setting of
temperature
Reset the appropriate temperature
Nozzle oxidation
Replace nozzle
Suction ability is low Blow - by Check the connection of vacuum outlet
Check the installation of glass tube
Excessive solder waste
storage in glass tube
Removing solder waste from glass
tube
Filter degradation
Replacement of filter
Unable to absorb
solder
Solder hole blocked Under heating condition, use cleaning
pin to clean heating element
Solder insufficiently hot
enough
Ensure heat setting is correct and
allow time to melt solder
Tin absorption hole
blocked, cannot be
dredged
Solder waste
accumulate at the end of
heating element
Take off the glass tube, use the
soldering iron to heat the steel pipe
back to remove the solder waste, and
then use the cleaning pin to dredge
2. Take the spring out from the glass tube ,then remove the solder waste
3. Put the spring back into the glass tube, then fix the glass tube back into
position.
Press the rear of the holder back into position (B) , then the lever (A) will
move down and lock automatically.
LCD DESOLDERING STATION/English
glass tube
aluminum piece filter
B. Press
A. Down
31.07.2020, Versions-Nr. 002
7
Manuel d'utilisation
137-2292
STATION DE DESSOUDAGE LCD
FR
131.07.2020, Versions-Nr. 002
STATION DE DESSOUDAGE LCD
Description
La station de dessoudage 137-2292 est conçue pour un dessoudage sans
plomb. Le chauffage rapide et le grand vide sont adaptés pour tous les types de
composants DIP.
Une conception solide, une utilisation d'une seule main et une aspiration puissante
permettent de retirer facilement les résidus de soudure des circuits imprimés simple
face ou double face.
N° de modèle 137-2292
Type de connecteur
mâle
EU F Schuko Royaume-Uni Type G
Tension (V c.a.) 220 V-240 V~ 50 Hz
Puissance de soudure 90 W
Consommation 140 W
Température 160 °C → 480 °C
Pression de vide ±600 mm Hg
Élément chauffant Chauffage en céramique
Accessoires Pointe de rechange x 3 (Ø 1,2 (sur le pistolet) / Ø 1,0 / Ø 1,5 mm)
Outil de nettoyage x 3
(Ø 0,7 / Ø 0,9 / Ø 1,2 mm) Éponge x 4 (Ø 20,8 x 1 + Ø 16,8 x 3)
CE, RoHS
Taille de la station (mm) 172 x 135 x 190
Poids (kg) 1,6
Tabla de contenidos
Idiomas:
Otros manuales de Herramientas eléctricas de RS PRO
